Han Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Han Wang has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Hong Shen
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
7 shared publications Zhenqiang Yao
5 shared publicationsHong Shen
4 shared publicationsJingwen Yan
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
2 shared publicationsJun Hu
School of Mechanical Engineering, Shanghai Jiao Tong University, Shanghai 200240, China
2 shared publicationsKai Zhao
2 shared publications
Latest Publications
- 1 November 2020
- Published by Elsevier in Optics & Laser Technology
- Vol. 131
Surface evolution in ultrafast laser ablation of fused silica
- 1 November 2020
- Published by Elsevier in Optics & Laser Technology
- Vol. 131
Surface evolution in ultrafast laser ablation of fused silica
- 1 July 2020
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 55, 87-95
Experimental study on direct fabrication of micro channel on fused silica by picosecond laser
- 1 July 2020
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 55, 87-95
Experimental study on direct fabrication of micro channel on fused silica by picosecond laser
- 7 May 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (6) , 065011
Experimental study on two-phase boiling in wavy copper microchannels fabricated with ultrafast laser micromachining
In this study, the sinusoidal wavy (SW) copper microchannels with triangular cross section were fabricated with the ultrafast laser micromachining approach. The flow boiling of de-ionized water in SW microchannels were experimentally studied under mass fluxes of 43.43–217.15 kg (m 2 s) −1 and heat fluxes of 0–590 kW m −2 . The flow patterns in the SW microchannels were visually observed and the boiling heat transfer characteristics were analyzed based on the obtained data. It shows the SW microchannel has a maximum enhancement of 127.7% in the local heat transfer coefficient with an acceptable increase of pressure loss compared to the straight one in the present work. In SW microchannels, a low degree of superheat can trigger the onset of nucleate boiling. A slow decreasing tendency of local heat transfer coefficient under a high effective heat flux or a high vapor quality was observed. The heat transfer mechanism of flow boiling in SW microchannels was analyzed based on the experimental visualization. Nucleate boiling and thin film evaporation are the dominant modes under different thermal boundary conditions. The flow boiling instability phenomenon in microchannels can be diminished using the wavy structures.
- 7 May 2020
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 30 (6) , 065011
Experimental study on two-phase boiling in wavy copper microchannels fabricated with ultrafast laser micromachining
In this study, the sinusoidal wavy (SW) copper microchannels with triangular cross section were fabricated with the ultrafast laser micromachining approach. The flow boiling of de-ionized water in SW microchannels were experimentally studied under mass fluxes of 43.43–217.15 kg (m 2 s) −1 and heat fluxes of 0–590 kW m −2 . The flow patterns in the SW microchannels were visually observed and the boiling heat transfer characteristics were analyzed based on the obtained data. It shows the SW microchannel has a maximum enhancement of 127.7% in the local heat transfer coefficient with an acceptable increase of pressure loss compared to the straight one in the present work. In SW microchannels, a low degree of superheat can trigger the onset of nucleate boiling. A slow decreasing tendency of local heat transfer coefficient under a high effective heat flux or a high vapor quality was observed. The heat transfer mechanism of flow boiling in SW microchannels was analyzed based on the experimental visualization. Nucleate boiling and thin film evaporation are the dominant modes under different thermal boundary conditions. The flow boiling instability phenomenon in microchannels can be diminished using the wavy structures.
- 1 December 2019
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 7 (4)
Welding Fused Silica Glass by Picosecond Pulsed Laser With Low Numerical Aperture
Researches on glass welding using tightly focused ultrafast lasers have attracted much attention. However, optical systems with low numerical aperture (NA) in laser material processing are commonly used in industry applications. Transmission welding of two fused silica glass plates is performed by using picosecond laser irradiation with low NA in this study. The welding strength under different process parameters such as focal position, pulse energy, and scanning velocity is measured. The role of the modification in welding process is demonstrated through the interior morphology in single-piece glass samples. A model is presented to predict the position of the bottom tip of the modification (BTM). The model considers the propagation property of the laser beam and the incubation effect of modification threshold. The numerical and experimental positions of BTM are compared. The model can give an idea for selecting process parameters to the achievement of glass welding for low NA optical system in ultrafast laser welding.
- 1 December 2019
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 7 (4)
Welding Fused Silica Glass by Picosecond Pulsed Laser With Low Numerical Aperture
Researches on glass welding using tightly focused ultrafast lasers have attracted much attention. However, optical systems with low numerical aperture (NA) in laser material processing are commonly used in industry applications. Transmission welding of two fused silica glass plates is performed by using picosecond laser irradiation with low NA in this study. The welding strength under different process parameters such as focal position, pulse energy, and scanning velocity is measured. The role of the modification in welding process is demonstrated through the interior morphology in single-piece glass samples. A model is presented to predict the position of the bottom tip of the modification (BTM). The model considers the propagation property of the laser beam and the incubation effect of modification threshold. The numerical and experimental positions of BTM are compared. The model can give an idea for selecting process parameters to the achievement of glass welding for low NA optical system in ultrafast laser welding.
- 12 April 2019
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 141 (6) , 1-27
A Two-Step Model for Multiple Picosecond and Femtosecond Pulses Ablation of Fused Silica
The morphology of microchannels machined by multiple ultrafast laser pulses with 500 fs and 8 ps durations on fused silica plate is predicted by a two-step model with experimental validation in present work. A spike structure at crater boundary with different scales in 500 fs and 8 ps pulse ablation is found in the numerical investigation, which could be attributed to diffraction and attenuation of light intensity in both cases. To analyze the evolution of crater morphology and damaged area with an increasing number of pulses, the distribution of light intensity, lattice temperature, and self-trapped excitons density during certain pulses are studied. The results showed that 500 fs pulses lead to smoother crater boundary, smaller heat affected zone, and larger electrical damage area with respect to 8 ps pulses.
- 12 April 2019
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 141 (6) , 1-27
A Two-Step Model for Multiple Picosecond and Femtosecond Pulses Ablation of Fused Silica
The morphology of microchannels machined by multiple ultrafast laser pulses with 500 fs and 8 ps durations on fused silica plate is predicted by a two-step model with experimental validation in present work. A spike structure at crater boundary with different scales in 500 fs and 8 ps pulse ablation is found in the numerical investigation, which could be attributed to diffraction and attenuation of light intensity in both cases. To analyze the evolution of crater morphology and damaged area with an increasing number of pulses, the distribution of light intensity, lattice temperature, and self-trapped excitons density during certain pulses are studied. The results showed that 500 fs pulses lead to smoother crater boundary, smaller heat affected zone, and larger electrical damage area with respect to 8 ps pulses.
- 10 October 2018
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 6 (4) , 044501
Experiment-Based Quantitative Analysis of Picosecond Pulse-Induced Morphological Changes in Fused Silica
Due to its excellent quality, fused silica has been widely used in various industrial applications. The nonlinear absorptive nature of ultrafast laser pulses enables the induction of morphological changes within the bulk transparent materials. In this study, the interior modification of fused silica is induced by a picosecond pulsed laser, and the relationship between processing parameters and the modification geometry is demonstrated. Three different patterns are identified according to the geometric characteristics of the modification. Furthermore, a simple experiment-based model considering the incubation effect is put forward to predict picosecond pulse-induced morphological changes in fused silica.
- 10 October 2018
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 6 (4) , 044501
Experiment-Based Quantitative Analysis of Picosecond Pulse-Induced Morphological Changes in Fused Silica
Due to its excellent quality, fused silica has been widely used in various industrial applications. The nonlinear absorptive nature of ultrafast laser pulses enables the induction of morphological changes within the bulk transparent materials. In this study, the interior modification of fused silica is induced by a picosecond pulsed laser, and the relationship between processing parameters and the modification geometry is demonstrated. Three different patterns are identified according to the geometric characteristics of the modification. Furthermore, a simple experiment-based model considering the incubation effect is put forward to predict picosecond pulse-induced morphological changes in fused silica.
- 1 October 2018
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 35, 373-381
Process modelling in laser forming of doubly-curved sheets from cylinder shapes
- 1 October 2018
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 35, 373-381
Process modelling in laser forming of doubly-curved sheets from cylinder shapes
- 1 September 2018
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 145, 42-52
Laser forming of doubly curved plates using minimum energy principle and comprehensive strain control
- 1 September 2018
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 145, 42-52
Laser forming of doubly curved plates using minimum energy principle and comprehensive strain control
- 9 June 2017
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 5 (3) , 031006
A Prediction Model for Ablation Fluence Threshold in Femtosecond Laser Processing of Fused Silica
The manufacture of micro–nano structures in transparent dielectrics is becoming increasingly important due to the applications in medical and biological sciences. The femtosecond pulsed laser, with its selectivity, high precision, and three-dimensional direct writing nature, is an ideal tool for this processing technology. In this paper, an improved model for the prediction of ablation crater shape and fluence threshold in femtosecond laser processing of fused silica is presented, in which self-trapping excitons and electrons' relaxation are involved to depict ionization process, Thornber's and Keldysh's models are employed to estimate ionization rate precisely, and a novel ablation criterion is proposed to judge ablation. Moreover, the relationship between the ablation fluence threshold and laser pulse duration is investigated with three different extrapolation methods. The results indicate that no matter which extrapolation method is employed, the ablation fluence thresholds predicted by the presented model agree with the published data.
- 9 June 2017
- Published by ASME International in Journal of Micro and Nano-Manufacturing
- Vol. 5 (3) , 031006
A Prediction Model for Ablation Fluence Threshold in Femtosecond Laser Processing of Fused Silica
The manufacture of micro–nano structures in transparent dielectrics is becoming increasingly important due to the applications in medical and biological sciences. The femtosecond pulsed laser, with its selectivity, high precision, and three-dimensional direct writing nature, is an ideal tool for this processing technology. In this paper, an improved model for the prediction of ablation crater shape and fluence threshold in femtosecond laser processing of fused silica is presented, in which self-trapping excitons and electrons' relaxation are involved to depict ionization process, Thornber's and Keldysh's models are employed to estimate ionization rate precisely, and a novel ablation criterion is proposed to judge ablation. Moreover, the relationship between the ablation fluence threshold and laser pulse duration is investigated with three different extrapolation methods. The results indicate that no matter which extrapolation method is employed, the ablation fluence thresholds predicted by the presented model agree with the published data.
- 20 June 2016
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 138 (9) , 091003
Heating Position Planning in Laser Forming of Single Curved Shapes Based on Probability Convergence
Inverse problem in laser forming involves the heating position planning and the determination of heating parameters. In this study, the heating positions are optimized in laser forming of single curved shapes based on the processing efficiency. The algorithm uses a probability function to initialize the heating position that is considered to be the bending points. The optimization process is to minimize the total processing time through adjusting the heating positions by considering the boundary conditions of the offset distances, the minimum bending angle, and the minimum distance between two adjacent heating positions. The optimized results are compared with those obtained by the distance-based model as well as the experimental data.
- 20 June 2016
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 138 (9) , 091003
Heating Position Planning in Laser Forming of Single Curved Shapes Based on Probability Convergence
Inverse problem in laser forming involves the heating position planning and the determination of heating parameters. In this study, the heating positions are optimized in laser forming of single curved shapes based on the processing efficiency. The algorithm uses a probability function to initialize the heating position that is considered to be the bending points. The optimization process is to minimize the total processing time through adjusting the heating positions by considering the boundary conditions of the offset distances, the minimum bending angle, and the minimum distance between two adjacent heating positions. The optimized results are compared with those obtained by the distance-based model as well as the experimental data.