Mee Kee Wong
Mee Kee Wong has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Azmi Mohd Shariff
Universiti Teknologi PETRONAS
5 shared publications - Henry Chee Yew Foo
Department of Chemical and Energy Engineering, Faculty of Engineering and Science, Curtin University Malaysia, Miri, Sarawak, Malaysia
4 shared publications - Inn Shi Tan
Department of Chemical and Energy Engineering, Faculty of Engineering and Science, Curtin University Malaysia, CDT 250, 98009 Miri, Sarawak, Malaysia
4 shared publications - Agus Saptoro
Department of Chemical and Energy Engineering, Curtin University Malaysia, Miri, Malaysia
3 shared publications - Foster Kofi Ayittey
Curtin University, Malaysia Campus
3 shared publications Man Kee Lam
3 shared publications
Latest Publications
- Open Access
- 4 October 2025
- Published by Elsevier in Biomass and Bioenergy
- Vol. 204
Advancing L-Lactic acid production through ultrasonic-assisted microbubbles-mediated ozonolysis of Eucheuma denticulatum hydrocolloid for enhanced D-galactose yield
- 4 October 2025
- Published by Elsevier in Biomass and Bioenergy
- Vol. 204
Open AccessAdvancing L-Lactic acid production through ultrasonic-assisted microbubbles-mediated ozonolysis of Eucheuma denticulatum hydrocolloid for enhanced D-galactose yield
- Open Access
- 26 September 2024
- Published by Elsevier in Journal of the Taiwan Institute of Chemical Engineers
- Vol. 177
Durable polylactic acid bionanocomposites with biomass-derived nanocellulose additives: Recent advances in production
- 26 September 2024
- Published by Elsevier in Journal of the Taiwan Institute of Chemical Engineers
- Vol. 177
Open AccessDurable polylactic acid bionanocomposites with biomass-derived nanocellulose additives: Recent advances in production
- 23 November 2023
- Published by Elsevier in Chinese Chemical Letters
- Vol. 35 (8)
Thermal pyrolysis conversion of methane to hydrogen (H2): A review on process parameters, reaction kinetics and techno-economic analysis
- 23 November 2023
- Published by Elsevier in Chinese Chemical Letters
- Vol. 35 (8)
Thermal pyrolysis conversion of methane to hydrogen (H2): A review on process parameters, reaction kinetics and techno-economic analysis
- Open Access
- 23 July 2023
- Published by Taylor & Francis in Bioengineered
- Vol. 14 (1) , 246-289
Sustainable circular biorefinery approach for novel building blocks and bioenergy production from algae using microbial fuel cell
The imminent need for transition to a circular biorefinery using microbial fuel cells (MFC), based on the valorization of renewable resources, will ameliorate the carbon footprint induced by industrialization. MFC catalyzed by bioelectrochemical process drew significant attention initially for its exceptional potential for integrated production of biochemicals and bioenergy. Nonetheless, the associated costly bioproduct production and slow microbial kinetics have constrained its commercialization. This review encompasses the potential and development of macroalgal biomass as a substrate in the MFC system for L-lactic acid (L-LA) and bioelectricity generation. Besides, an insight into the state-of-the-art technological advancement in the MFC system is also deliberated in detail. Investigations in recent years have shown that MFC developed with different anolyte enhances power density from several µW/m2 up to 8160 mW/m2. Further, this review provides a plausible picture of macroalgal-based L-LA and bioelectricity circular biorefinery in the MFC system for future research directions.
- 23 July 2023
- Published by Taylor & Francis in Bioengineered
- Vol. 14 (1) , 246-289
Open AccessSustainable circular biorefinery approach for novel building blocks and bioenergy production from algae using microbial fuel cell
The imminent need for transition to a circular biorefinery using microbial fuel cells (MFC), based on the valorization of renewable resources, will ameliorate the carbon footprint induced by industrialization. MFC catalyzed by bioelectrochemical process drew significant attention initially for its exceptional potential for integrated production of biochemicals and bioenergy. Nonetheless, the associated costly bioproduct production and slow microbial kinetics have constrained its commercialization. This review encompasses the potential and development of macroalgal biomass as a substrate in the MFC system for L-lactic acid (L-LA) and bioelectricity generation. Besides, an insight into the state-of-the-art technological advancement in the MFC system is also deliberated in detail. Investigations in recent years have shown that MFC developed with different anolyte enhances power density from several µW/m2 up to 8160 mW/m2. Further, this review provides a plausible picture of macroalgal-based L-LA and bioelectricity circular biorefinery in the MFC system for future research directions.
- 3 September 2020
- Published by Wiley in Asia-Pacific Journal of Chemical Engineering
- Vol. 16 (1)
Energy‐saving process configurations for monoethanolamine‐based CO2 capture system
It is evident from several researches that combining a couple of process modifications is effective in reducing reboiler duty in the chemical absorption‐based carbon capture process. Although extensive works on these combined modifications exist in literature, studies on combined lean vapour compression (LVC) and rich solvent preheating (RSP) are unavailable, despite their potentials as promising energy‐saving technologies. This simulation‐based study therefore explored standalone and combined process modifications capable of minimizing reboiler duty in monoethanolamine (MEA)‐based postcombustion CO2 capture system. Using the electrolyte nonrandom two‐liquid (ELECNRTL) property method in Aspen Plus®, a rigorous rate‐based simulation was performed and validated for conventional MEA‐based capture system. Subsequently, three main process modifications, namely, LVC, RSP and combined LVC and RSP, were investigated to evaluate their impact on energy consumption level in the stripping column. The modifications were able to reduce the total equivalent electrical penalty on the power plant by 12.94%, 5.24% and 14.48%, respectively. The results from this study demonstrate that a detailed optimization of the combined LVC and RSP process configuration could achieve considerable energy saving in MEA‐based capture systems.
- 3 September 2020
- Published by Wiley in Asia-Pacific Journal of Chemical Engineering
- Vol. 16 (1)
Energy‐saving process configurations for monoethanolamine‐based CO2 capture system
It is evident from several researches that combining a couple of process modifications is effective in reducing reboiler duty in the chemical absorption‐based carbon capture process. Although extensive works on these combined modifications exist in literature, studies on combined lean vapour compression (LVC) and rich solvent preheating (RSP) are unavailable, despite their potentials as promising energy‐saving technologies. This simulation‐based study therefore explored standalone and combined process modifications capable of minimizing reboiler duty in monoethanolamine (MEA)‐based postcombustion CO2 capture system. Using the electrolyte nonrandom two‐liquid (ELECNRTL) property method in Aspen Plus®, a rigorous rate‐based simulation was performed and validated for conventional MEA‐based capture system. Subsequently, three main process modifications, namely, LVC, RSP and combined LVC and RSP, were investigated to evaluate their impact on energy consumption level in the stripping column. The modifications were able to reduce the total equivalent electrical penalty on the power plant by 12.94%, 5.24% and 14.48%, respectively. The results from this study demonstrate that a detailed optimization of the combined LVC and RSP process configuration could achieve considerable energy saving in MEA‐based capture systems.
- 21 April 2020
- Published by Wiley in Greenhouse Gases: Science and Technology
- Vol. 10 (3) , 631-642
Parametric study and optimisation of hot K2CO3‐based post‐combustion CO2 capture from a coal‐fired power plant
Detailed parametric analyses on a post‐combustion carbon dioxide (CO2) capture system using a hot potassium carbonate solution was completed using a rate‐based simulation study. The system was simulated in Aspen Plus® V10, adopting the electrolyte non‐random two‐liquid property package. A base case study of the system was validated using literature data. Parametric analyses were then performed to study the effect of vital system parameters on CO2 capture rate and stripper reboiler duty. These system parameters include: (i) reflux ratio of stripping column (ii) lean solvent flowrate (iii) flue gas flowrate (iv) lean solvent concentration (v) lean solvent temperature (vi) flue gas temperature and (vii) absorber operating pressure. Changes in the lean solvent concentration (from 25 to 45 wt%) and absorber operating pressure (from 0.5 to 2.5 MPa) were observed to have the most significant effects on the overall performance of the capture system. Increasing both parameters showed substantial declines in the reboiler duty and resulted in remarkable increases in the corresponding carbon capture levels, and vice versa. The performance of various packing types in the absorber and stripper columns were also studied. Among the packing types examined, Flexipac Koch Metal 1Y was observed to yield the best system performance. The results from the parametric analyses were used to propose an optimised model that was able to improve carbon removal rate by 12.61% and decreased stripper reboiler duty by 14.86%. © 2020 Society of Chemical Industry and John Wiley & Sons, Ltd.
- 21 April 2020
- Published by Wiley in Greenhouse Gases: Science and Technology
- Vol. 10 (3) , 631-642
Parametric study and optimisation of hot K2CO3‐based post‐combustion CO2 capture from a coal‐fired power plant
Detailed parametric analyses on a post‐combustion carbon dioxide (CO2) capture system using a hot potassium carbonate solution was completed using a rate‐based simulation study. The system was simulated in Aspen Plus® V10, adopting the electrolyte non‐random two‐liquid property package. A base case study of the system was validated using literature data. Parametric analyses were then performed to study the effect of vital system parameters on CO2 capture rate and stripper reboiler duty. These system parameters include: (i) reflux ratio of stripping column (ii) lean solvent flowrate (iii) flue gas flowrate (iv) lean solvent concentration (v) lean solvent temperature (vi) flue gas temperature and (vii) absorber operating pressure. Changes in the lean solvent concentration (from 25 to 45 wt%) and absorber operating pressure (from 0.5 to 2.5 MPa) were observed to have the most significant effects on the overall performance of the capture system. Increasing both parameters showed substantial declines in the reboiler duty and resulted in remarkable increases in the corresponding carbon capture levels, and vice versa. The performance of various packing types in the absorber and stripper columns were also studied. Among the packing types examined, Flexipac Koch Metal 1Y was observed to yield the best system performance. The results from the parametric analyses were used to propose an optimised model that was able to improve carbon removal rate by 12.61% and decreased stripper reboiler duty by 14.86%. © 2020 Society of Chemical Industry and John Wiley & Sons, Ltd.
- 21 January 2020
- Published by Wiley in Greenhouse Gases: Science and Technology
- Vol. 10 (1) , 130-146
Process modifications for a hot potassium carbonate‐based CO2 capture system: a comparative study
Chemical absorption using hot potassium carbonate (K2CO3) is believed to be a more energy‐efficient post‐combustion CO2 capture technology as compared to conventional amine‐based absorption processes. That notwithstanding, literature information on how process modifications could render this technology more appealing are limited. In this study, seven different modified process configurations have been investigated to observe their impacts on the system performances of a typical hot K2CO3‐based capture system. The results demonstrate that flue gas precooling is capable of improving the carbon removal level in the K2CO3‐based capture system by 11.46% over the base case value. This was achieved by precooling the flue gas stream from 110 to 70°C before feeding into the absorber column. Other modified process systems such as the rich solvent pre‐heating and lean vapour compression were equally observed to decrease the specific stripper reboiler duty by 24.28% and 21.38%, respectively. The findings from this research prove that process modifications are capable of enhancing the system performances of the hot K2CO3‐based post‐combustion CO2 capture technology. © 2020 Society of Chemical Industry and John Wiley & Sons, Ltd.
- 21 January 2020
- Published by Wiley in Greenhouse Gases: Science and Technology
- Vol. 10 (1) , 130-146
Process modifications for a hot potassium carbonate‐based CO2 capture system: a comparative study
Chemical absorption using hot potassium carbonate (K2CO3) is believed to be a more energy‐efficient post‐combustion CO2 capture technology as compared to conventional amine‐based absorption processes. That notwithstanding, literature information on how process modifications could render this technology more appealing are limited. In this study, seven different modified process configurations have been investigated to observe their impacts on the system performances of a typical hot K2CO3‐based capture system. The results demonstrate that flue gas precooling is capable of improving the carbon removal level in the K2CO3‐based capture system by 11.46% over the base case value. This was achieved by precooling the flue gas stream from 110 to 70°C before feeding into the absorber column. Other modified process systems such as the rich solvent pre‐heating and lean vapour compression were equally observed to decrease the specific stripper reboiler duty by 24.28% and 21.38%, respectively. The findings from this research prove that process modifications are capable of enhancing the system performances of the hot K2CO3‐based post‐combustion CO2 capture technology. © 2020 Society of Chemical Industry and John Wiley & Sons, Ltd.
- 1 November 2016
- Published by Elsevier in Journal of Natural Gas Science and Engineering
- Vol. 36, 305-313
In situ measurement of physical solubility of carbon dioxide in loaded aqueous monoethanolamine by Raman spectroscopy
- 1 November 2016
- Published by Elsevier in Journal of Natural Gas Science and Engineering
- Vol. 36, 305-313
In situ measurement of physical solubility of carbon dioxide in loaded aqueous monoethanolamine by Raman spectroscopy