Sleiman Bou Sleiman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sleiman Bou Sleiman has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
Mohammed Ismail
Khalifa Semiconductor Research Center (KSRC) at Khalifa University of Science, Technology and Research Abu Dhabi UAE
11 shared publicationsAmneh Akour
Analog VLSI Lab, ECE Department, The Ohio State University, Columbus, USA
1 shared publication- Ana Rusu
School of Electrical Engineering and Computer Science, KTH Royal Institute of Technology, Stockholm, Sweden
1 shared publication Jad G. Atallah
ECS, ICT, Royal Institute of Technology (KTH), Stockholm, Sweden
1 shared publicationMohammad Alhawari
Khalifa Semiconductor Research Center (KSRC) at Khalifa University of Science, Technology and Research Abu Dhabi UAE
1 shared publicationNaveen Naraharisetti
Analog VLSI Lab, The Ohio State University, Columbus, Ohio 43210
1 shared publication
Latest Publications
- 6 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A 0.23 mW, On-Chip, self-calibrating RF amplitude detector in 65 nm CMOS
We present an RF amplitude detector with a conversion gain of −3 V/V for RF amplitude range 0 to 0.6 Vp in 65nm CMOS. On-chip self-calibration structure that automatically corrects the variations within the RF detector itself is proposed. Silicon measurement results show the self-calibration structure improves the detection error of the non-calibrated RF amplitude detector to less than 10% at only 0.23mW power consumption.
- 6 March 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
A 0.23 mW, On-Chip, self-calibrating RF amplitude detector in 65 nm CMOS
We present an RF amplitude detector with a conversion gain of −3 V/V for RF amplitude range 0 to 0.6 Vp in 65nm CMOS. On-chip self-calibration structure that automatically corrects the variations within the RF detector itself is proposed. Silicon measurement results show the self-calibration structure improves the detection error of the non-calibrated RF amplitude detector to less than 10% at only 0.23mW power consumption.
- 4 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 22 (8) , 1716-1726
Dynamic Self-Regulated Charge Pump With Improved Immunity to PVT Variations
A charge pump (CP) design that simultaneously reduces current mismatch and sensitivity to process, voltage, and temperature variations is presented. The self-biased and self-regulated circuit uses a dual-feedback mechanism with a replica CP to dynamically stabilize and equalize the currents over a wide output voltage range under varying operating conditions. The circuit is further analyzed and designed in 90-nm CMOS. Extensive corner and Monte Carlo runs are used to verify its current matching capabilities as well as its stability and response within a phase locked loop. The CP achieves near perfect current matching for a wide output voltage range and for temperatures ranging from -30 °C to 90 °C and a power supply between 1.08 and 1.32 V.
- 4 September 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
- Vol. 22 (8) , 1716-1726
Dynamic Self-Regulated Charge Pump With Improved Immunity to PVT Variations
A charge pump (CP) design that simultaneously reduces current mismatch and sensitivity to process, voltage, and temperature variations is presented. The self-biased and self-regulated circuit uses a dual-feedback mechanism with a replica CP to dynamically stabilize and equalize the currents over a wide output voltage range under varying operating conditions. The circuit is further analyzed and designed in 90-nm CMOS. Extensive corner and Monte Carlo runs are used to verify its current matching capabilities as well as its stability and response within a phase locked loop. The CP achieves near perfect current matching for a wide output voltage range and for temperatures ranging from -30 °C to 90 °C and a power supply between 1.08 and 1.32 V.
- 1 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1100-1103
A nanoscale CMOS charge pump with near perfect current matching
A drain-switching charge pump (CP) design is presented with near perfect current matching and extended flat current response over a range of process, voltage, and temperature variations. Current mismatch is compensated dynamically without the need for a replica charge pump or extended digitally-assisted calibration routines. The self-regulated circuit uses several simple yet effective feedback mechanisms to overcome the basic shortcomings of nanometer devices and reduced power supplies. The circuit is designed in 90nm CMOS and simulated extensively using Monte Carlo analysis while sweeping the operating temperature to provide statistically relevant operating conditions. The proposed design achieves near perfect current matching at output voltages between 0.16V and 0.98V for temperatures ranging from -30 to 90 degrees Celsius and a power supply between 1.08V and 1.32V.
- 1 August 2013
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1100-1103
A nanoscale CMOS charge pump with near perfect current matching
A drain-switching charge pump (CP) design is presented with near perfect current matching and extended flat current response over a range of process, voltage, and temperature variations. Current mismatch is compensated dynamically without the need for a replica charge pump or extended digitally-assisted calibration routines. The self-regulated circuit uses several simple yet effective feedback mechanisms to overcome the basic shortcomings of nanometer devices and reduced power supplies. The circuit is designed in 90nm CMOS and simulated extensively using Monte Carlo analysis while sweeping the operating temperature to provide statistically relevant operating conditions. The proposed design achieves near perfect current matching at output voltages between 0.16V and 0.98V for temperatures ranging from -30 to 90 degrees Celsius and a power supply between 1.08V and 1.32V.
- 4 May 2012
- Published by Wiley
- p. 557-580
Design and Test of Robust CMOS RF and MM‐Wave Radios
- 1 January 2012
- Published by Springer Nature
Built-in-Self-Test and Digital Self-Calibration for RF SoCs
- 1 January 2012
- Published by Springer Nature
Built-in-Self-Test and Digital Self-Calibration for RF SoCs
- 1 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 492-495
Enabling efficient built-in-self-calibration for RFICs
Robustness and yield enhancement techniques for RF circuits and systems are gaining accelerating traction due to increased PVT variability in nanometer CMOS. One of the more viable approaches that make use of the increasingly heterogeneous systems is digitally-assisted RF, enabling circuit programmability and flexibility. With the inclusion of the more robust digital, RF circuits' impairments may be successfully overcome or significantly diminished. This is enabled by implementing self-calibration mechanisms on top of self-test routines. In this paper, we highlight the basic requirements for enabling the on-chip self-calibration loop and discuss the main design steps. We also show an LNA circuit example demonstrating self-healing capabilities.
- 1 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 492-495
Enabling efficient built-in-self-calibration for RFICs
Robustness and yield enhancement techniques for RF circuits and systems are gaining accelerating traction due to increased PVT variability in nanometer CMOS. One of the more viable approaches that make use of the increasingly heterogeneous systems is digitally-assisted RF, enabling circuit programmability and flexibility. With the inclusion of the more robust digital, RF circuits' impairments may be successfully overcome or significantly diminished. This is enabled by implementing self-calibration mechanisms on top of self-test routines. In this paper, we highlight the basic requirements for enabling the on-chip self-calibration loop and discuss the main design steps. We also show an LNA circuit example demonstrating self-healing capabilities.
- 1 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 188-191
Mixed-Mode I/Q mismatches compensation in low-IF quadrature receivers
The performance of the quadrature receivers are degraded due to the gain and phase mismatch in I and Q channels. In this paper we develop a mixed-mode technique for self calibration in quadrature receivers. A novel mismatch measurement and estimation scheme using an RF amplitude detector and the IC's digital core is shown. Then, digital and digitally-assisted analog correction is employed to remove phase and gain mismatches in the quadrature channels. The mixed-mode configuration is shown to be of low complexity and overhead. Test cases for QAM-16 demonstrate the effectiveness of the proposed approach in suppressing quadrature mismatch and enhancing image rejection.
- 1 December 2011
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 188-191
Mixed-Mode I/Q mismatches compensation in low-IF quadrature receivers
The performance of the quadrature receivers are degraded due to the gain and phase mismatch in I and Q channels. In this paper we develop a mixed-mode technique for self calibration in quadrature receivers. A novel mismatch measurement and estimation scheme using an RF amplitude detector and the IC's digital core is shown. Then, digital and digitally-assisted analog correction is employed to remove phase and gain mismatches in the quadrature channels. The mixed-mode configuration is shown to be of low complexity and overhead. Test cases for QAM-16 demonstrate the effectiveness of the proposed approach in suppressing quadrature mismatch and enhancing image rejection.
- 1 August 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 477-480
Millimeter-wave BiST and BiSC using a high-definition sub-ranged detector in 90nm CMOS
A wideband CMOS mm-Wave amplitude detector for on-chip self-test and calibration is presented. The high-conversion-gain detector enables accurate on-chip amplitude measurements and allows for the prediction of key RF parameters. The detector operates across the 60 GHz band and achieves a dynamic range of 0-0.5 V and a sensitivity of -9 V/V. The detector's practical use in mm-wave Built-in-Self-Test (BiST) and Built-in-Self-Calibration (BiSC) circuits is demonstrated using a 60 GHz CMOS LNA. Simulation results show that the LNA gain, compression point, and intermodulation distortion are predicted with minimal error. The detector and LNA are built in IBM's 90 nm CMOS technology.
- 1 August 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 477-480
Millimeter-wave BiST and BiSC using a high-definition sub-ranged detector in 90nm CMOS
A wideband CMOS mm-Wave amplitude detector for on-chip self-test and calibration is presented. The high-conversion-gain detector enables accurate on-chip amplitude measurements and allows for the prediction of key RF parameters. The detector operates across the 60 GHz band and achieves a dynamic range of 0-0.5 V and a sensitivity of -9 V/V. The detector's practical use in mm-wave Built-in-Self-Test (BiST) and Built-in-Self-Calibration (BiSC) circuits is demonstrated using a 60 GHz CMOS LNA. Simulation results show that the LNA gain, compression point, and intermodulation distortion are predicted with minimal error. The detector and LNA are built in IBM's 90 nm CMOS technology.
- 1 May 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02714302,p. 2059-2062
Transceiver parameter detection using a high conversion gain RF amplitude detector
In this work, we present a wideband CMOS RF amplitude detector for on-chip self-test and calibration. The high conversion gain detector enables accurate on-chip amplitude measurements and allows for accurate transceiver parameter prediction. The detector operates from 500MHz to 9GHz while detecting signal amplitudes from 0 to 0.7V with a sensitivity of -10V/V. Several test cases are presented to demonstrate the functionality of the design and its ability to detect key RF block parameters such as gain, distortion, and phase mismatch. The detector is built in 0.18μm CMOS and consumes less than 0.8mW from a 1.8V power supply.
- 1 May 2010
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- No. 02714302,p. 2059-2062
Transceiver parameter detection using a high conversion gain RF amplitude detector
In this work, we present a wideband CMOS RF amplitude detector for on-chip self-test and calibration. The high conversion gain detector enables accurate on-chip amplitude measurements and allows for accurate transceiver parameter prediction. The detector operates from 500MHz to 9GHz while detecting signal amplitudes from 0 to 0.7V with a sensitivity of -10V/V. Several test cases are presented to demonstrate the functionality of the design and its ability to detect key RF block parameters such as gain, distortion, and phase mismatch. The detector is built in 0.18μm CMOS and consumes less than 0.8mW from a 1.8V power supply.
- 1 December 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 807-810
A CMOS amplitude detector for RF-BIST and calibration
In this work, we present a wideband CMOS RF amplitude detector for on-chip self-test and calibration. The proposed detector offers a high conversion gain (-10V/V), thus allowing for very fine detection of RF amplitude changes, and has a wide dynamic range enabling detection of RF peak amplitude changes between 0 and 0.7V. Additionally, its wideband capabilities make it especially useful for today's multiband multi-standard applications such as WLAN and WiMAX. The detector is built in 0.18¿m CMOS and uses a 1.8V power supply.
- 1 December 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 807-810
A CMOS amplitude detector for RF-BIST and calibration
In this work, we present a wideband CMOS RF amplitude detector for on-chip self-test and calibration. The proposed detector offers a high conversion gain (-10V/V), thus allowing for very fine detection of RF amplitude changes, and has a wide dynamic range enabling detection of RF peak amplitude changes between 0 and 0.7V. Additionally, its wideband capabilities make it especially useful for today's multiband multi-standard applications such as WLAN and WiMAX. The detector is built in 0.18¿m CMOS and uses a 1.8V power supply.