Władysław Kryłłowicz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Władysław Kryłłowicz has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Grzegorz Liśkiewicz
Łódź University of Technology
6 shared publications - Kirill Kabalyk
Institute of Turbomachinery, Lodz University of Technology, Wólczańska 217/221, 93-005 Łódź, Poland
5 shared publications - Krzysztof Sobczak
Faculty of Mechanical Engineering, Institute of Turbomachinery, Lodz University of Technology, 90-924 Lodz, Poland
3 shared publications Longin Horodko
Institute of Turbomachinery, Lodz University of Technology, Poland
3 shared publications- Zbigniew Kozanecki
Lodz University of Technology
3 shared publications - Krzysztof Kantyka
Institute of Turbomachinery, Lodz University of Technology, Wólczańska Str. 217/221, 93-005 Łódź, Poland
2 shared publications
Latest Publications
- 7 April 2021
- Published by Wiley in Journal of Turbomachinery
- Vol. 143 (5)
Experimental Study of Vaneless Diffuser Rotating Stall Development and Cell-Merging Phenomena
This paper describes the vaneless diffuser rotating stall (VDRS) development and cell-merging phenomena. A centrifugal compressor’s lifespan may be limited by flow instabilities occurring in off-design operation. One such instability is the VDRS, which generates oscillating, asymmetrical flow fields in the diffuser and, thus, undesired forces acting on the rotor. Understanding and prevention of VDRS behavior are crucial for achieving safe and undisturbed compressor operation. Experimental measurements of centrifugal compressors operating under the influence of VDRS have been presented. Two different approaches were used for the identification of VDRS: pressure measurements and two-dimensional (2D) particle image velocimetry (PIV). Frequency analysis based on spectral maps and cell development processes were investigated. The presented results showed that mass flowrate has an impact on the rotating frequency of both the entire structure and single cells. Additionally, it affects radial cell size, which grows with compressor throttling and ultimately reaches the length of the diffuser. During the experiments, the cell-merging phenomenon was observed which has not been widely described in the literature. The results presented in this paper allow a better understanding of vaneless diffuser rotating stall behavior. The phenomenon of the change of cell size and frequency could be very important for machine fatigue. Cell-merging could also have an impact on the machine’s vibrations and flow stability. Since it is believed that VDRS is one of the factors inducing surge, its understanding and prevention may have a positive influence on surge margins.
- 7 April 2021
- Published by Wiley in Journal of Turbomachinery
- Vol. 143 (5)
Experimental Study of Vaneless Diffuser Rotating Stall Development and Cell-Merging Phenomena
This paper describes the vaneless diffuser rotating stall (VDRS) development and cell-merging phenomena. A centrifugal compressor’s lifespan may be limited by flow instabilities occurring in off-design operation. One such instability is the VDRS, which generates oscillating, asymmetrical flow fields in the diffuser and, thus, undesired forces acting on the rotor. Understanding and prevention of VDRS behavior are crucial for achieving safe and undisturbed compressor operation. Experimental measurements of centrifugal compressors operating under the influence of VDRS have been presented. Two different approaches were used for the identification of VDRS: pressure measurements and two-dimensional (2D) particle image velocimetry (PIV). Frequency analysis based on spectral maps and cell development processes were investigated. The presented results showed that mass flowrate has an impact on the rotating frequency of both the entire structure and single cells. Additionally, it affects radial cell size, which grows with compressor throttling and ultimately reaches the length of the diffuser. During the experiments, the cell-merging phenomenon was observed which has not been widely described in the literature. The results presented in this paper allow a better understanding of vaneless diffuser rotating stall behavior. The phenomenon of the change of cell size and frequency could be very important for machine fatigue. Cell-merging could also have an impact on the machine’s vibrations and flow stability. Since it is believed that VDRS is one of the factors inducing surge, its understanding and prevention may have a positive influence on surge margins.
- Open Access
Unstable Flow Structures Present at Different Rotational Velocities of the Centrifugal Compressor
Unstable flow structures cause inevitable energy losses in all power energy systems, including turbomachines. In this study, a set of analyses was conducted with the use of spectral maps on the pressure signals obtained from an industrial centrifugal compressor. The spectral maps provide one a detailed visualization of the flow conditions present in the machine along the performance curve and to distinguish the flow phenomena present prior to the surge. The method accuracy is especially useful in detecting the inlet recirculation. The study was conducted at four impeller rotational speeds with varying loads imposed by a valve at the outlet. At each speed, the machine experienced different stages of unstable flow conditions prior to the surge. Five main frequency peaks that appeared in all cases were identified and discussed. The surge was observed at all impeller speeds. At lower ones, however, it appeared at higher valve closures. At higher speeds, the surge was much more intense. The study has also shown that the inlet recirculation appears also for the closed-type industrial impeller. The phenomenon was present in all conditions. The higher impeller speed, the faster onset of the inlet recirculation was. This structure has a strong potential for an early instability warning because it appears in various types of impellers, has a very particular spectral structure and its positioning is very predictable. This study gives another example of the inlet recirculation universality and potential for efficient anti-surge protection.
Open AccessUnstable Flow Structures Present at Different Rotational Velocities of the Centrifugal Compressor
Unstable flow structures cause inevitable energy losses in all power energy systems, including turbomachines. In this study, a set of analyses was conducted with the use of spectral maps on the pressure signals obtained from an industrial centrifugal compressor. The spectral maps provide one a detailed visualization of the flow conditions present in the machine along the performance curve and to distinguish the flow phenomena present prior to the surge. The method accuracy is especially useful in detecting the inlet recirculation. The study was conducted at four impeller rotational speeds with varying loads imposed by a valve at the outlet. At each speed, the machine experienced different stages of unstable flow conditions prior to the surge. Five main frequency peaks that appeared in all cases were identified and discussed. The surge was observed at all impeller speeds. At lower ones, however, it appeared at higher valve closures. At higher speeds, the surge was much more intense. The study has also shown that the inlet recirculation appears also for the closed-type industrial impeller. The phenomenon was present in all conditions. The higher impeller speed, the faster onset of the inlet recirculation was. This structure has a strong potential for an early instability warning because it appears in various types of impellers, has a very particular spectral structure and its positioning is very predictable. This study gives another example of the inlet recirculation universality and potential for efficient anti-surge protection.
- Open Access
- 3 December 2018
- Published by EDP Sciences
- Vol. 70, 03006
Technical problems with compression units in mechanical vapour recompression systems
The evidence gathered during works on two prototype heat recovery systems is summarised. The first installation is a low-temperature vapour recompression system, whereas the second is a high-temperature (from an industrial viewpoint) installation. Vapour-contaminated air is the working medium. The authors focused their attention on machine issues mainly. All compressors described below were designed at the Lodz University of Technology.
- 3 December 2018
- Published by EDP Sciences
- Vol. 70, 03006
Open AccessTechnical problems with compression units in mechanical vapour recompression systems
The evidence gathered during works on two prototype heat recovery systems is summarised. The first installation is a low-temperature vapour recompression system, whereas the second is a high-temperature (from an industrial viewpoint) installation. Vapour-contaminated air is the working medium. The authors focused their attention on machine issues mainly. All compressors described below were designed at the Lodz University of Technology.
- 11 June 2018
- Published by ASME International
Numerical Study of Off-Design Centrifugal Compressor Operation and Flow Phenomena Preceding Surge
The paper outlines the results of a numerical analysis of a low-speed centrifugal compressor operating at design and off-design conditions. This included the analysis of surge predecessors. Surge is known to be a reason for the severe damage of compressing units and systems working with them. This phenomenon is also known to have a very quick and sudden onset. Therefore, it is important to understand the nature of flow structures that appear locally prior to the surge onset. It is generally believed that these could include: impeller rotating stall (abrupt or progressive), diffuser rotating stall, and inlet or outlet recirculation. This classification is, however, not sharp and observed flows could represent only selected features of the different phenomena. It is also not clear which structure is most likely to appear in a given system. The paper presents an exhaustive examination of flow structures observed in the case of a low-speed centrifugal compressor. Transient numerical simulations were conducted for both design and off-design conditions. The results were related to the experimental data presented in another paper. The numerical test domain consisted of blower, volute, inlet nozzle and elements of inlet and outlet channels assuring no influence of the boundary conditions on the local flow fluctuations. The analysis of the results included many factors such as: flow in the volute, flow in the impeller, flow in the diffuser and stagnation zones. The most significant flow structures appearing at pre-surge were identified as the inlet recirculation and the phenomenon representing some features of the rotating stall. The simulation, confirmed by experimental data, allowed for a better understanding of pre-surge flow structures in the case of a low-speed compressor, which is very important for the identification of early surge indicators.
- 11 June 2018
- Published by ASME International
Numerical Study of Off-Design Centrifugal Compressor Operation and Flow Phenomena Preceding Surge
The paper outlines the results of a numerical analysis of a low-speed centrifugal compressor operating at design and off-design conditions. This included the analysis of surge predecessors. Surge is known to be a reason for the severe damage of compressing units and systems working with them. This phenomenon is also known to have a very quick and sudden onset. Therefore, it is important to understand the nature of flow structures that appear locally prior to the surge onset. It is generally believed that these could include: impeller rotating stall (abrupt or progressive), diffuser rotating stall, and inlet or outlet recirculation. This classification is, however, not sharp and observed flows could represent only selected features of the different phenomena. It is also not clear which structure is most likely to appear in a given system. The paper presents an exhaustive examination of flow structures observed in the case of a low-speed centrifugal compressor. Transient numerical simulations were conducted for both design and off-design conditions. The results were related to the experimental data presented in another paper. The numerical test domain consisted of blower, volute, inlet nozzle and elements of inlet and outlet channels assuring no influence of the boundary conditions on the local flow fluctuations. The analysis of the results included many factors such as: flow in the volute, flow in the impeller, flow in the diffuser and stagnation zones. The most significant flow structures appearing at pre-surge were identified as the inlet recirculation and the phenomenon representing some features of the rotating stall. The simulation, confirmed by experimental data, allowed for a better understanding of pre-surge flow structures in the case of a low-speed compressor, which is very important for the identification of early surge indicators.
- Open Access
- 1 June 2018
- Published by Walter de Gruyter GmbH in Mechanics and Mechanical Engineering
- Vol. 22 (2) , 455-464
Modernization of Centrifugal Chlorine Compressor
In this paper modernization of a three-stage chlorine centrifugal compressor, in which chlorine is pressurized has been described. Machine nominal mass flow has been increased by 20% and the pressure rise has remained almost unchanged. New construction concept has been chosen basing on analysis of different design variants. Calculations were conducted with one-dimensional method with usage of in-house developed code. Algorithms implemented to this program are based on empirical studies and wide experience in compressor modernization and design. Moreover, results of modified machine acceptance test results, which satisfies VDI norm 2045/ISO 5389 has been presented.
- 1 June 2018
- Published by Walter de Gruyter GmbH in Mechanics and Mechanical Engineering
- Vol. 22 (2) , 455-464
Open AccessModernization of Centrifugal Chlorine Compressor
In this paper modernization of a three-stage chlorine centrifugal compressor, in which chlorine is pressurized has been described. Machine nominal mass flow has been increased by 20% and the pressure rise has remained almost unchanged. New construction concept has been chosen basing on analysis of different design variants. Calculations were conducted with one-dimensional method with usage of in-house developed code. Algorithms implemented to this program are based on empirical studies and wide experience in compressor modernization and design. Moreover, results of modified machine acceptance test results, which satisfies VDI norm 2045/ISO 5389 has been presented.
- 9 December 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 232 (21) , 3964-3976
A differential planetary gear for regulation drive design and selected tests
Radial fans with efficiency regulation during their work using variational geometry of the rotor have not been used in industries until now, despite the fact that this is the most economically effective regulation method. One of the causes for this was the lack of a convenient method of transferring drive to moving blades of the fan. This paper presents an innovative method of transferring drive on the blades using a differential planetary gear. The construction is described, and a strength calculation methodology and tests confirming correctness of work are shown as well. The presented solution can become a new standard in the construction of energy fans.
- 9 December 2017
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
- Vol. 232 (21) , 3964-3976
A differential planetary gear for regulation drive design and selected tests
Radial fans with efficiency regulation during their work using variational geometry of the rotor have not been used in industries until now, despite the fact that this is the most economically effective regulation method. One of the causes for this was the lack of a convenient method of transferring drive to moving blades of the fan. This paper presents an innovative method of transferring drive on the blades using a differential planetary gear. The construction is described, and a strength calculation methodology and tests confirming correctness of work are shown as well. The presented solution can become a new standard in the construction of energy fans.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1889, 020015
Influence of definition of impeller-vaneless diffuser boundary on physical validity of numerical simulations of viscid flow in the vaneless diffuser of a centrifugal compressor: A short review of case studies
The study aims to work out a set of recommendations for setting a proper distance between the trailing edge of impeller and the interface boundary, which on the one hand would not be too large to overpredict the impeller efficiency and not too short to introduce artificial wake-like flow structures at diffuser inlet on the other. Three individual two-element stages belonging to three different types known as medium- and low-flow coefficient stages are studied. Besides of the design flow coefficient, the focus is on the influence of impeller tip Mach number on the optimal location of the boundary.
- 1 January 2017
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1889, 020015
Influence of definition of impeller-vaneless diffuser boundary on physical validity of numerical simulations of viscid flow in the vaneless diffuser of a centrifugal compressor: A short review of case studies
The study aims to work out a set of recommendations for setting a proper distance between the trailing edge of impeller and the interface boundary, which on the one hand would not be too large to overpredict the impeller efficiency and not too short to introduce artificial wake-like flow structures at diffuser inlet on the other. Three individual two-element stages belonging to three different types known as medium- and low-flow coefficient stages are studied. Besides of the design flow coefficient, the focus is on the influence of impeller tip Mach number on the optimal location of the boundary.
- 1 January 2017
- Published by European Turbomachinery Society
Technical and Aerodynamical Aspects of a High Pressure Synthesis Gas Turbocompressor Modernization
The article is devoted to the description of the modernization of a multihull process centrifugal compressor for synthesis gas. The main reason for the revamp was the desire to adapt the conventional machine (45 years of operation) for newer operational requirements: the decrease of compressor discharge pressure to the level of 140 bar from the level of 211 bar with the corresponding alteration of the mass flow rate. The scheme accepted as a final modernization conception required the manufacturing of three completely new rotor and casing assemblies. Major design modifications concerned the impellers’ geometry, introduction of vaneless diffusers and the abradable labyrinth seals. Most of the stages were “optimized” using the in-house semi-empirical 1D code and ANSYS CFX commercial code. The performance of a single optimized stage was tested experimentally. The paper reveals the main results of these measurements and their comparison to numerical simulations results. The start-up tests of the modernized assembly showed its almost 100% conformity to the requirements in the output and the efficiency rise of about 5%.
- 1 January 2017
- Published by European Turbomachinery Society
Technical and Aerodynamical Aspects of a High Pressure Synthesis Gas Turbocompressor Modernization
The article is devoted to the description of the modernization of a multihull process centrifugal compressor for synthesis gas. The main reason for the revamp was the desire to adapt the conventional machine (45 years of operation) for newer operational requirements: the decrease of compressor discharge pressure to the level of 140 bar from the level of 211 bar with the corresponding alteration of the mass flow rate. The scheme accepted as a final modernization conception required the manufacturing of three completely new rotor and casing assemblies. Major design modifications concerned the impellers’ geometry, introduction of vaneless diffusers and the abradable labyrinth seals. Most of the stages were “optimized” using the in-house semi-empirical 1D code and ANSYS CFX commercial code. The performance of a single optimized stage was tested experimentally. The paper reveals the main results of these measurements and their comparison to numerical simulations results. The start-up tests of the modernized assembly showed its almost 100% conformity to the requirements in the output and the efficiency rise of about 5%.
- 11 January 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 230 (3) , 260-271
Experimental investigation of the influence of the inlet duct configuration on the unstable operation of a single-stage centrifugal blower
The article is devoted to the experimental investigation of the interactions between the amplitudes and frequencies of surge in a single-stage centrifugal blower and the configuration of its inlet duct. In this work, the term ‘configuration’ implies the combination of the following: the volume of the duct, the presence of the filter inside the duct and the inlet guide vane position. The high-response pressure measurements were performed at three points along the impeller shroud (inlet, middle, outlet) and at a single point downstream the volute outlet and then processed with the use of fast Fourier transform (FFT). The results of the measurements show that the response of the surging system to a change introduced into the duct’s configuration is complex. The closure of the inlet guide vane typically causes a drop in the amplitude and frequency of fluctuating pressure. The introduction of a filter body into the duct most often damps the amplitudes of fluctuations, but leaves the frequencies unaltered. The change of the duct’s volume controls the rate of this damping.
- 11 January 2016
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part A: Journal of Power and Energy
- Vol. 230 (3) , 260-271
Experimental investigation of the influence of the inlet duct configuration on the unstable operation of a single-stage centrifugal blower
The article is devoted to the experimental investigation of the interactions between the amplitudes and frequencies of surge in a single-stage centrifugal blower and the configuration of its inlet duct. In this work, the term ‘configuration’ implies the combination of the following: the volume of the duct, the presence of the filter inside the duct and the inlet guide vane position. The high-response pressure measurements were performed at three points along the impeller shroud (inlet, middle, outlet) and at a single point downstream the volute outlet and then processed with the use of fast Fourier transform (FFT). The results of the measurements show that the response of the surging system to a change introduced into the duct’s configuration is complex. The closure of the inlet guide vane typically causes a drop in the amplitude and frequency of fluctuating pressure. The introduction of a filter body into the duct most often damps the amplitudes of fluctuations, but leaves the frequencies unaltered. The change of the duct’s volume controls the rate of this damping.
- Open Access
- 4 January 2015
- Published by Walter de Gruyter GmbH in Open Engineering
- Vol. 5 (1)
Technical aspects of a large size industrial process turbo compressor revamp
This paper describes several modernization aspects of the process 8 MW air compressor and its driver. The main aim of the revamp was to increase internal efficiencies of both the compressor and turbine and increase the load of the compressor without additional power consumption. The original pressure ratio was preserved. To meet these requirements a redesign of the flow path of both machineswas necessary.Moreover, the turbineworking conditions were changed from extraction-condensing to condensing. In terms of compressor, impeller blade redesign, adaptation of diffusers and Abradable seals were a part of the scope. The revamp was completed in April 2014 with all the requirements met. This paper covers the general outline and a comparison of the original and modernized machine operating parameters, design and technical assumptions and also describes some problematic issues which occurred during the realization of the project.
- 4 January 2015
- Published by Walter de Gruyter GmbH in Open Engineering
- Vol. 5 (1)
Open AccessTechnical aspects of a large size industrial process turbo compressor revamp
This paper describes several modernization aspects of the process 8 MW air compressor and its driver. The main aim of the revamp was to increase internal efficiencies of both the compressor and turbine and increase the load of the compressor without additional power consumption. The original pressure ratio was preserved. To meet these requirements a redesign of the flow path of both machineswas necessary.Moreover, the turbineworking conditions were changed from extraction-condensing to condensing. In terms of compressor, impeller blade redesign, adaptation of diffusers and Abradable seals were a part of the scope. The revamp was completed in April 2014 with all the requirements met. This paper covers the general outline and a comparison of the original and modernized machine operating parameters, design and technical assumptions and also describes some problematic issues which occurred during the realization of the project.