Yuan Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuan Lu has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Paul Munroe
School of Materials Science and Engineering, University of New South Wales, Sydney, NSW 2052, Australia
3 shared publications F.E. Kennedy
2 shared publicationsFrancis E. Kennedy
2 shared publicationsI. Baker
2 shared publicationsIan Baker
2 shared publications- Jian Feng Yang
State Key Laboratory for Mechanical Behavior of Materials, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication
Latest Publications
- Open Access
- 19 May 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 199, 012007
Three-phase Unbalanced Interval Power Flow Calculation of Low-voltage Distribution Network with Distributed PV Power Generation
- 19 May 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 199, 012007
Open AccessThree-phase Unbalanced Interval Power Flow Calculation of Low-voltage Distribution Network with Distributed PV Power Generation
- 1 April 2017
- Published by Elsevier in Intermetallics
- Vol. 83, 17-28
The effect of sliding velocity on the dry sliding wear of nanophase Fe30Ni20Mn25Al25 against yttria-stabilized zirconia
- 1 April 2017
- Published by Elsevier in Intermetallics
- Vol. 83, 17-28
The effect of sliding velocity on the dry sliding wear of nanophase Fe30Ni20Mn25Al25 against yttria-stabilized zirconia
- 1 February 2015
- Published by Elsevier in Tribology International
- Vol. 82, 534-542
Contact temperatures and their influence on wear during pin-on-disk tribotesting
- 1 February 2015
- Published by Elsevier in Tribology International
- Vol. 82, 534-542
Contact temperatures and their influence on wear during pin-on-disk tribotesting
- 1 August 2013
- Published by Elsevier in Intermetallics
- Vol. 39, 94-103
A comparison of dry sliding wear of Fe30Ni20Mn25Al25 at room temperature and elevated temperature
- 1 August 2013
- Published by Elsevier in Intermetallics
- Vol. 39, 94-103
A comparison of dry sliding wear of Fe30Ni20Mn25Al25 at room temperature and elevated temperature
- 1 February 2013
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 745-746, 667-672
Porous TiN Ceramics Fabricated by Carbothermal Reduction Method
Porous TiN ceramics with high porosity and uniform pore structure was prepared following the carbothermal reduction reaction between TiO2 and carbon. Influences of sintering additives and particle size of TiO2 on the microstructure and mechanical properties of porous TiN ceramics were investigated. Microstructure and mechanical properties of porous TiN ceramics were studied by XRD, SEM and three-point bending measurement. XRD analysis proved that the TiN phase has completely formed after reaction. In addition, SEM analysis showed that the resultant porous TiN ceramics were composed of fine grains with uniform pore structure. The addition of La2O3 not only accelerated the densification of porous TiN ceramics, but also decreased the porosity and increased the flexural strength. With a decrease in TiO2 particle size, the linear shrinkage increased and the porosity decreased accordingly.
- 1 February 2013
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 745-746, 667-672
Porous TiN Ceramics Fabricated by Carbothermal Reduction Method
Porous TiN ceramics with high porosity and uniform pore structure was prepared following the carbothermal reduction reaction between TiO2 and carbon. Influences of sintering additives and particle size of TiO2 on the microstructure and mechanical properties of porous TiN ceramics were investigated. Microstructure and mechanical properties of porous TiN ceramics were studied by XRD, SEM and three-point bending measurement. XRD analysis proved that the TiN phase has completely formed after reaction. In addition, SEM analysis showed that the resultant porous TiN ceramics were composed of fine grains with uniform pore structure. The addition of La2O3 not only accelerated the densification of porous TiN ceramics, but also decreased the porosity and increased the flexural strength. With a decrease in TiO2 particle size, the linear shrinkage increased and the porosity decreased accordingly.