Lech Starczewski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lech Starczewski has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
Robert Nyc
Military Institute of Armored and Automotive Technology (WITPiS)
3 shared publications- Bogdan Garbarz
Centrum Technologii Metalurgicznych Łukasiewicz–Górnośląski Instytut Technologiczny 44‐100 Gliwice Poland
2 shared publications - Jarosław MARCISZ
Łukasiewicz Research Network – Institute for Ferrous Metallurgy
2 shared publications Krzysztof Szcześniak
Military Institute of Armour and Automotive Technology, Armament and Equipment Material Analysis Laboratory, 1 Okuniewska Street, 05-070 Sulejówek, Poland
2 shared publications- Michał Gmitrzuk
Military Institute of Armoured and Automotive Technology, Poland
2 shared publications A Piatkowska
1 shared publication
Latest Publications
- Open Access
- 1 July 2026
- Published by Centrum Rzeczoznawstwa Budowlanego Sp z. o.o. in Inżynieria Bezpieczeństwa Obiektów Antropogenicznych
- No. 2,p. 109-117
Passive double-layer shielding systems, requirements and solutions
This article presents a general classification of protection levels used by NATO forces, as well as basic requirements for passive vehicle protection systems. It presents the conditions for using lightweight armor systems as additional armor to the basic armor of a combat vehicle, in order to increase the level of protection while minimizing the vehicle's weight. Particular attention is paid to two-layer protective systems composed of a ceramic layer and a laminate layer. A synthetic discussion of the physical processes occurring in such systems when penetrated by a hard-core anti-tank projectile is provided. The Florence analytical model was used to consider the effectiveness of the two-layer armor, which was used to determine the material configuration and create the shield models. Ballistic tests verified the effectiveness of the shields by exposing them to fire from a 7.62 AP anti-tank projectile with a hard tungsten core, with an energy of approximately 3.65 kJ and an impact velocity exceeding 900 m/s. Based on the results of ballistic tests and observations of the behavior of the tested shield models, an analysis of the energy absorption mechanisms of the protective system components was conducted. The balance of internal energy accumulated by the system was also presented. The paper contains a discussion of the results and conclusions.
- 1 July 2026
- Published by Centrum Rzeczoznawstwa Budowlanego Sp z. o.o. in Inżynieria Bezpieczeństwa Obiektów Antropogenicznych
- No. 2,p. 109-117
Open AccessPassive double-layer shielding systems, requirements and solutions
This article presents a general classification of protection levels used by NATO forces, as well as basic requirements for passive vehicle protection systems. It presents the conditions for using lightweight armor systems as additional armor to the basic armor of a combat vehicle, in order to increase the level of protection while minimizing the vehicle's weight. Particular attention is paid to two-layer protective systems composed of a ceramic layer and a laminate layer. A synthetic discussion of the physical processes occurring in such systems when penetrated by a hard-core anti-tank projectile is provided. The Florence analytical model was used to consider the effectiveness of the two-layer armor, which was used to determine the material configuration and create the shield models. Ballistic tests verified the effectiveness of the shields by exposing them to fire from a 7.62 AP anti-tank projectile with a hard tungsten core, with an energy of approximately 3.65 kJ and an impact velocity exceeding 900 m/s. Based on the results of ballistic tests and observations of the behavior of the tested shield models, an analysis of the energy absorption mechanisms of the protective system components was conducted. The balance of internal energy accumulated by the system was also presented. The paper contains a discussion of the results and conclusions.
- 10 April 2025
- Published by Index Copernicus in PROBLEMY TECHNIKI UZBROJENIA
- Vol. 172 (1) , 45-76
CHARACTERISTICS OF THE ADD-ON ARMOUR MADE OF PERFORATED NANOBAINITIC STEEL PLATES FULFILLING REQUIREMENTS OF THE 3-RD LEVEL OF BALLISTIC PROTECTION ACCORDING TO STANAG 4569
The paper contains results of ballistic tests and material investigations on add–on armour in form of a panel composed only of two perforated plates made of nanobainitic steel and intended to protect the base armour against firing with small arms ammunition under multi–hit conditions relating to the third level of protection of STANAG 4569. Perforated plates were manufactured using nanobainitic steel characterised by hardness within the range of 565 HBW to 600 HBW, Rp0.2 > 1300 MPa and Rm > 2000 MPa. Based on the correlation of places where bullets hit the perforated plate with types of damage found in the perforated plates, and with traces located on the surface of the solid plate, critical areas characterised by a potentially lowest ballistic resistance were identified. A modification of the two–plate panel design made of nanobainitic perforated plates was developed to provide full protection of base armour against multi–hit perpendicular firing with ammunition assigned to the third level of protection of STANAG 4569.
- 10 April 2025
- Published by Index Copernicus in PROBLEMY TECHNIKI UZBROJENIA
- Vol. 172 (1) , 45-76
CHARACTERISTICS OF THE ADD-ON ARMOUR MADE OF PERFORATED NANOBAINITIC STEEL PLATES FULFILLING REQUIREMENTS OF THE 3-RD LEVEL OF BALLISTIC PROTECTION ACCORDING TO STANAG 4569
The paper contains results of ballistic tests and material investigations on add–on armour in form of a panel composed only of two perforated plates made of nanobainitic steel and intended to protect the base armour against firing with small arms ammunition under multi–hit conditions relating to the third level of protection of STANAG 4569. Perforated plates were manufactured using nanobainitic steel characterised by hardness within the range of 565 HBW to 600 HBW, Rp0.2 > 1300 MPa and Rm > 2000 MPa. Based on the correlation of places where bullets hit the perforated plate with types of damage found in the perforated plates, and with traces located on the surface of the solid plate, critical areas characterised by a potentially lowest ballistic resistance were identified. A modification of the two–plate panel design made of nanobainitic perforated plates was developed to provide full protection of base armour against multi–hit perpendicular firing with ammunition assigned to the third level of protection of STANAG 4569.
- 15 October 2021
- Published by Siec Badawcza Lukasiewicz - Instytut Metalurgii Zelaza im. St. Staszica in Journal of Metallic Materials
- Vol. 73 (2) , 13-39
Development of technology for the production of a lightweight observation and protective container (LOOK) made of nanostructured ultra-strength steels
The article contains results of research and analyses concerning application of nanostructured bainitic steel in the form of plates for manufacturing of armour components. The presented results of examination of microstructure and properties include a wide range of laboratory experiments and industrial tests, which resulted in the achievement of the assumed functional properties. In the period of 2017-2021, a scientific and industrial consortium consisting of Łukasiewicz – Institute of Ferrous Metallurgy (leader); WITPiS, Tarnów Mechanical Works, Alchemia and Heatmasters Poland carried out a project funded by the POIR 04.01.04 programme aimed to develop the design and to manufacture an observation and protective container with a specified resistance to penetration by armour-piercing projectiles and with a lower mass of steel armouring in relation to that currently produced. The aim of the project was achieved by using armour plates made of nanostructured bainitic steel (nanobainitic), which are characterised by high resistance to high-energy impact concentrated in a small area. The technological tests carried out in the project mainly concerned the development of a new container and industrial technology of armour plates production and their application in the armour of this container. Based on the results of investigation of the semi-industrial scale material, the optimum chemical composition for industrial scale melting and casting was determined. An industrial technology for the production of plates of nano-structured bainitic steel was developed, which includes the following processes: smelting and casting, preliminary heat treatment and ingot hot processing, as well as hot rolling, final heat treatment, and surface treatment. A test batch of the material in the form of 1500×2470 mm armoured plates was fabricated under industrial conditions. The final result of the project is a container armoured with bainitic nanostructured steel plates with implementation documentation and a technology for producing armoured plates from this steel under the technical and technological conditions of domestic steel manufacturers.
- 15 October 2021
- Published by Siec Badawcza Lukasiewicz - Instytut Metalurgii Zelaza im. St. Staszica in Journal of Metallic Materials
- Vol. 73 (2) , 13-39
Development of technology for the production of a lightweight observation and protective container (LOOK) made of nanostructured ultra-strength steels
The article contains results of research and analyses concerning application of nanostructured bainitic steel in the form of plates for manufacturing of armour components. The presented results of examination of microstructure and properties include a wide range of laboratory experiments and industrial tests, which resulted in the achievement of the assumed functional properties. In the period of 2017-2021, a scientific and industrial consortium consisting of Łukasiewicz – Institute of Ferrous Metallurgy (leader); WITPiS, Tarnów Mechanical Works, Alchemia and Heatmasters Poland carried out a project funded by the POIR 04.01.04 programme aimed to develop the design and to manufacture an observation and protective container with a specified resistance to penetration by armour-piercing projectiles and with a lower mass of steel armouring in relation to that currently produced. The aim of the project was achieved by using armour plates made of nanostructured bainitic steel (nanobainitic), which are characterised by high resistance to high-energy impact concentrated in a small area. The technological tests carried out in the project mainly concerned the development of a new container and industrial technology of armour plates production and their application in the armour of this container. Based on the results of investigation of the semi-industrial scale material, the optimum chemical composition for industrial scale melting and casting was determined. An industrial technology for the production of plates of nano-structured bainitic steel was developed, which includes the following processes: smelting and casting, preliminary heat treatment and ingot hot processing, as well as hot rolling, final heat treatment, and surface treatment. A test batch of the material in the form of 1500×2470 mm armoured plates was fabricated under industrial conditions. The final result of the project is a container armoured with bainitic nanostructured steel plates with implementation documentation and a technology for producing armoured plates from this steel under the technical and technological conditions of domestic steel manufacturers.
- Open Access
- 14 December 2020
- Published by Lukasiewicz Research Network - Institute of Industrial Organic Chemistry in Materiały Wysokoenergetyczne / High Energy Materials
- p. 173-183
Determining the degree of pulse absorption of air blast wave by spaced material systems
The paper presents the results of a study to determine the degree of attenuation of a detonation wave pulse generated by a spherical ceresin-phlegmatized hexogen charge, by spaced material systems. The systems were mounted on a ballistic pendulum and the amount of energy absorbed was determined based on the change in pendulum swing. The spaced panels with absorbing elements, simulated the flat bottom of a vehicle exposed to a single blast.
- 14 December 2020
- Published by Lukasiewicz Research Network - Institute of Industrial Organic Chemistry in Materiały Wysokoenergetyczne / High Energy Materials
- p. 173-183
Open AccessDetermining the degree of pulse absorption of air blast wave by spaced material systems
The paper presents the results of a study to determine the degree of attenuation of a detonation wave pulse generated by a spherical ceresin-phlegmatized hexogen charge, by spaced material systems. The systems were mounted on a ballistic pendulum and the amount of energy absorbed was determined based on the change in pendulum swing. The spaced panels with absorbing elements, simulated the flat bottom of a vehicle exposed to a single blast.
- Open Access
- 28 December 2017
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 23 (6) , 794-801
Study of the shock wave effect on the deformation of the vehicle bottom using deformable energy absorbers
The paper reports a study on the effect of a shock wave generated during the detonation of 1.5 kg TNT on the deformation of a multi-layered energy absorber. The experiments were carried out using a custom- designed testing station. The detonation of the charge was performed using a steel plate with a blind hole in accordance with the requirements of the NATO (North Atlantic Treaty Organization) AEP -55 (Allied Engineering Publication) volume 2 document. In the tests, the total and plastic deformations of the plate modelling the basic armour of the lower part of the vehicle in configurations without and with a shock wave absorbing element (energy absorber) were measured. The comb gage method reported by the US Army Developmental Test Command was used in measurements of the total deformation of the model. The study has shown that an appropriate design of the energy absorber and the use of suitable materials in its fabrication allow the total deformation to be reduced. Moreover in this article numerical simulations of the deformation phenomenon of the multi-layered energy absorbers were shown. Numerical simulations have shown high numerical model compliance compared to the experimental studies. In the studies were achieved about 99 percent numerical with the real model correlation. DOI: http://dx.doi.org/10.5755/j01.mech.23.6.14119
- 28 December 2017
- Published by Kaunas University of Technology (KTU) in Mechanics
- Vol. 23 (6) , 794-801
Open AccessStudy of the shock wave effect on the deformation of the vehicle bottom using deformable energy absorbers
The paper reports a study on the effect of a shock wave generated during the detonation of 1.5 kg TNT on the deformation of a multi-layered energy absorber. The experiments were carried out using a custom- designed testing station. The detonation of the charge was performed using a steel plate with a blind hole in accordance with the requirements of the NATO (North Atlantic Treaty Organization) AEP -55 (Allied Engineering Publication) volume 2 document. In the tests, the total and plastic deformations of the plate modelling the basic armour of the lower part of the vehicle in configurations without and with a shock wave absorbing element (energy absorber) were measured. The comb gage method reported by the US Army Developmental Test Command was used in measurements of the total deformation of the model. The study has shown that an appropriate design of the energy absorber and the use of suitable materials in its fabrication allow the total deformation to be reduced. Moreover in this article numerical simulations of the deformation phenomenon of the multi-layered energy absorbers were shown. Numerical simulations have shown high numerical model compliance compared to the experimental studies. In the studies were achieved about 99 percent numerical with the real model correlation. DOI: http://dx.doi.org/10.5755/j01.mech.23.6.14119
- Open Access
- 28 October 2014
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 59 (3) , 1211-1216
Nanostructured Bainite-Austenite Steel for Armours Construction
Nanostructured bainite-austenite steels are applied in the armours construction due to their excellent combination of strength and ductility which enables to lower the armour weight and to improve the protection efficiency. Mechanical properties of the bainite-austenite steels can be controlled in the wide range by chemical composition and heat treatment. In the paper the results of investigation comprising measuring of quasi - static mechanical properties, dynamic yield stress and firing tests of bainite-austenite steel NANOS-BA® are presented. Reported results show that the investigated bainite-austenite steel can be used for constructing add-on armour and that the armour fulfils requirements of protection level 2 of STANAG 4569. Obtained reduction in weight of the tested NANOS-BA® plates in comparison with the present solutions is about 30%.
- 28 October 2014
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 59 (3) , 1211-1216
Open AccessNanostructured Bainite-Austenite Steel for Armours Construction
Nanostructured bainite-austenite steels are applied in the armours construction due to their excellent combination of strength and ductility which enables to lower the armour weight and to improve the protection efficiency. Mechanical properties of the bainite-austenite steels can be controlled in the wide range by chemical composition and heat treatment. In the paper the results of investigation comprising measuring of quasi - static mechanical properties, dynamic yield stress and firing tests of bainite-austenite steel NANOS-BA® are presented. Reported results show that the investigated bainite-austenite steel can be used for constructing add-on armour and that the armour fulfils requirements of protection level 2 of STANAG 4569. Obtained reduction in weight of the tested NANOS-BA® plates in comparison with the present solutions is about 30%.
- 1 July 2005
- Published by Springer Nature in Materials Science
- Vol. 41 (4) , 551-556
Boron Alloying and Laser Treatment to Improve Corrosion and Hydrogen Resistance of 25G Steel
- 1 July 2005
- Published by Springer Nature in Materials Science
- Vol. 41 (4) , 551-556
Boron Alloying and Laser Treatment to Improve Corrosion and Hydrogen Resistance of 25G Steel
- 1 September 2000
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 288 (2) , 284-287
Stress-textural indicators of tribological wear
- 1 September 2000
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 288 (2) , 284-287
Stress-textural indicators of tribological wear
- 1 January 1999
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 148 (1-4) , 941-945
Study of micromechanical properties of ion-beam mixed layers
- 1 January 1999
- Published by Elsevier in Nuclear Instruments and Methods in Physics Research Section B: Beam Interactions with Materials and Atoms
- Vol. 148 (1-4) , 941-945
Study of micromechanical properties of ion-beam mixed layers
- 1 March 1998
- Published by Elsevier in Surface and Coatings Technology
- Vol. 100-101, 33-37
Mechanisms of transferring the matter in a friction process in a tribology system: polymeric composite-metal
- 1 March 1998
- Published by Elsevier in Surface and Coatings Technology
- Vol. 100-101, 33-37
Mechanisms of transferring the matter in a friction process in a tribology system: polymeric composite-metal