Joseph J. Rencis
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Joseph J. Rencis has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Jiancheng Liu
Electrical Development Department of R&D Center, CRRC Qingdao Sifang Company, Ltd., Qingdao, China
2 shared publications Kwo‐Yih Jong
Engr., Yue Loong Motor Co., Taoyuan, Taiwan, 33099, Republic of China
2 shared publicationsQingping Huang
Mechanical Engineering Department Worcester Polytechnic Institute Worcester, Massachusetts 01609, USA
2 shared publicationsSachin S. Terdalkar
Department of Mechanical Engineering, University of Arkansas, Fayetteville, AR 72701, United States
2 shared publicationsAlexis Pham
University of the Pacific
1 shared publicationAshland Brown
University of the Pacific
1 shared publication
Latest Publications
- Open Access
- 11 September 2020
- Published by American Society for Engineering Education
- p. 25.752.1-25.752.26
Improving Student Learning Using Finite Element Learning Modules: An Update in Research Findings
- 11 September 2020
- Published by American Society for Engineering Education
- p. 25.752.1-25.752.26
Open AccessImproving Student Learning Using Finite Element Learning Modules: An Update in Research Findings
- Open Access
- 3 September 2020
- Published by American Society for Engineering Education
- p. 15.1110.1-15.1110.23
Structured Process For Writing, Revising, And Assessing Multiple Choice Quizzes
- 3 September 2020
- Published by American Society for Engineering Education
- p. 15.1110.1-15.1110.23
Open AccessStructured Process For Writing, Revising, And Assessing Multiple Choice Quizzes
- 1 July 2010
- Published by Elsevier in Chemical Physics Letters
- Vol. 494 (4-6) , 218-222
Nanoscale fracture in graphene
- 1 July 2010
- Published by Elsevier in Chemical Physics Letters
- Vol. 494 (4-6) , 218-222
Nanoscale fracture in graphene
- 1 April 2008
- Published by ASME International in Journal of Tribology
- Vol. 130 (2) , 021703
Rolling Stream Trails: An Alternative Cavitation Analysis
The rolling stream trail (RST) model introduces a new formulation of cavitation analysis of an eccentric journal bearing; it is presented as a preferred foundation for cavitation analysis of a journal bearing to replace Floberg’s streamer hypothesis that had been adopted by many investigators in recent past. Based on a careful reinterpretation of published experimental photographic data, noting the blunt-nosed shape of the interspersing space that separates adjacent wetting outlines at the rupture boundary, it stipulates a 3D flow structure for transition from the filled fluid film (FFF) to a cross-void fluid transportation process. The transition starts as a two-component composite rupture front and becomes an adhered film (AF) that is masked by rolled-on stream trails, which are drawn from the rupture front. The AF moves with the journal surface across the void to feed the FFF at the formation boundary. Upon averaged across a full period of the rupture front, Olsson’s equation for flow continuity relative to a moving cavitation boundary yields a moving speed of the rupture front that is proportional to the reciprocal of the width fraction of the wet pockets multiplied into the FFF pressure gradient. For all nonvanishing width fraction of the wet pockets, both rupture and formation boundaries move with finite speeds. RST is an initial value time-dependent problem that deals with both the FFF and AF that are joined at rupture and formation boundaries. The initial fluid content in the void span is bracketed between a dry void and a freshly cavitated wet void. As time progresses, transportation of AF across the void space and boundary motions form a coupled evolution process. Formulas for the boundary motions indicate that the formation boundary would become stationary simultaneously as the rupture boundary approaches the Swift–Stieber condition. For implementation of RST analysis, analytic functions originally derived by Sommerfeld in his classical paper are employed to construct FFF pressure profile and subsequently to calculate boundary speeds. Precision and robustness achieved in this approach assure viability of RST cavitation analysis. Results include temporal evolution profiles of the FFF pressure and the cavitation boundary trajectories. Basic concepts and mathematical formulation of RST are applicable to 2D problems. A scheme to include squeeze film motion is outlined.
- 1 April 2008
- Published by ASME International in Journal of Tribology
- Vol. 130 (2) , 021703
Rolling Stream Trails: An Alternative Cavitation Analysis
The rolling stream trail (RST) model introduces a new formulation of cavitation analysis of an eccentric journal bearing; it is presented as a preferred foundation for cavitation analysis of a journal bearing to replace Floberg’s streamer hypothesis that had been adopted by many investigators in recent past. Based on a careful reinterpretation of published experimental photographic data, noting the blunt-nosed shape of the interspersing space that separates adjacent wetting outlines at the rupture boundary, it stipulates a 3D flow structure for transition from the filled fluid film (FFF) to a cross-void fluid transportation process. The transition starts as a two-component composite rupture front and becomes an adhered film (AF) that is masked by rolled-on stream trails, which are drawn from the rupture front. The AF moves with the journal surface across the void to feed the FFF at the formation boundary. Upon averaged across a full period of the rupture front, Olsson’s equation for flow continuity relative to a moving cavitation boundary yields a moving speed of the rupture front that is proportional to the reciprocal of the width fraction of the wet pockets multiplied into the FFF pressure gradient. For all nonvanishing width fraction of the wet pockets, both rupture and formation boundaries move with finite speeds. RST is an initial value time-dependent problem that deals with both the FFF and AF that are joined at rupture and formation boundaries. The initial fluid content in the void span is bracketed between a dry void and a freshly cavitated wet void. As time progresses, transportation of AF across the void space and boundary motions form a coupled evolution process. Formulas for the boundary motions indicate that the formation boundary would become stationary simultaneously as the rupture boundary approaches the Swift–Stieber condition. For implementation of RST analysis, analytic functions originally derived by Sommerfeld in his classical paper are employed to construct FFF pressure profile and subsequently to calculate boundary speeds. Precision and robustness achieved in this approach assure viability of RST cavitation analysis. Results include temporal evolution profiles of the FFF pressure and the cavitation boundary trajectories. Basic concepts and mathematical formulation of RST are applicable to 2D problems. A scheme to include squeeze film motion is outlined.
- 1 January 2007
- Published by ASME International
- p. 637-645
Coupled Axisymmetric and Plane Stress Finite Element Model for the Stress Analysis of an Aircraft Engine Compressor
A coupled finite element model is proposed that can be used to carry out a static stress analysis of rotating parts. The rotating part consists of a disk modeled with four-node axisymmetric quadrilateral elements and blades modeled with four-node quadrilateral plane stress elements. The coupled finite element model is used to carry out a stress analysis of a simple rotor and complex aircraft engine compressor. The coupled model is compared to a solid ANSYS® finite element model using the twenty noded tetrahedral element. The major advantage of the coupled model over a three-dimensional model is that an analysis can be carried out quickly in the early design stage.
- 1 January 2007
- Published by ASME International
- p. 637-645
Coupled Axisymmetric and Plane Stress Finite Element Model for the Stress Analysis of an Aircraft Engine Compressor
A coupled finite element model is proposed that can be used to carry out a static stress analysis of rotating parts. The rotating part consists of a disk modeled with four-node axisymmetric quadrilateral elements and blades modeled with four-node quadrilateral plane stress elements. The coupled finite element model is used to carry out a stress analysis of a simple rotor and complex aircraft engine compressor. The coupled model is compared to a solid ANSYS® finite element model using the twenty noded tetrahedral element. The major advantage of the coupled model over a three-dimensional model is that an analysis can be carried out quickly in the early design stage.
- 1 January 2006
- Published by ASME International
- p. 41-50
Solving Beam Deflection Problems Using the Traditional Approach to Solve Axial and Torsion Problems
This paper presents a new approach to solving beam deflection problems. The approach involves the direct application of derived force-deformation formulas, a procedure commonly used with axial and torsion bar problems. This direct application of derived force-deformation formulas, referred to by the authors as Method of Segments, is extended to beam deflection analysis in order to provide a solution procedure for beams that is consistent in philosophy and application with that presented in most mechanics of materials textbooks for axially loaded bars and torsionally loaded shafts. The beam force-deformation formulas, involving slope and displacement, are derived by double integration for a beam of uniform cross-section, material and distributed loading with end shear forces and couples. Application of the formulas is direct and requires no integration or continuity equations. Furthermore, by identifying segments of uniform geometry, material and distributed loading, this approach can easily be applied to beams of discontinuous geometry and material that supports both concentrated and distributed loading.
- 1 January 2006
- Published by ASME International
- p. 41-50
Solving Beam Deflection Problems Using the Traditional Approach to Solve Axial and Torsion Problems
This paper presents a new approach to solving beam deflection problems. The approach involves the direct application of derived force-deformation formulas, a procedure commonly used with axial and torsion bar problems. This direct application of derived force-deformation formulas, referred to by the authors as Method of Segments, is extended to beam deflection analysis in order to provide a solution procedure for beams that is consistent in philosophy and application with that presented in most mechanics of materials textbooks for axially loaded bars and torsionally loaded shafts. The beam force-deformation formulas, involving slope and displacement, are derived by double integration for a beam of uniform cross-section, material and distributed loading with end shear forces and couples. Application of the formulas is direct and requires no integration or continuity equations. Furthermore, by identifying segments of uniform geometry, material and distributed loading, this approach can easily be applied to beams of discontinuous geometry and material that supports both concentrated and distributed loading.
- 1 January 2005
- Published by ASME International
- p. 11-20
Combined Approximation Reanalysis Coupled With Finite Element Stress Analysis for Multiple Geometric Changes in Early Design Stage
In this work a new graphically driven interactive stress reanalysis finite element technique has been developed so that an engineer can easily carry out manual geometric changes in a machine element during the early design stage. The interface allow an engineer to model a machine element in the commercial finite element code ANSYS® and then modify part geometry graphically to see instantaneous graphical changes in the stress and displacement contour plots. A reanalysis technique is used to enhance the computational performance for solving the modified problem; with the aim of obtaining results of acceptable accuracy in as short a period of time in order to emphasize the interactive nature of the design process. Two case studies are considered to demonstrate the effectiveness of the prototype graphically driven reanalysis finite element technique. The finite element type considered is a plane stress four-node quadrilateral based on a homogenous, isotropic, linear elastic material. Each case study considered multiple redesigns. A combined approximation reanalysis method is used to solve each redesigned problem. The first case study considers a plate with a hole with the goal to determine the hole shape that will minimize the stress concentration. The second case study considers a support bracket. The goal is to design the cantilever portion of the bracket to have uniform strength and to minimize the stress concentration at the fillet.
- 1 January 2005
- Published by ASME International
- p. 11-20
Combined Approximation Reanalysis Coupled With Finite Element Stress Analysis for Multiple Geometric Changes in Early Design Stage
In this work a new graphically driven interactive stress reanalysis finite element technique has been developed so that an engineer can easily carry out manual geometric changes in a machine element during the early design stage. The interface allow an engineer to model a machine element in the commercial finite element code ANSYS® and then modify part geometry graphically to see instantaneous graphical changes in the stress and displacement contour plots. A reanalysis technique is used to enhance the computational performance for solving the modified problem; with the aim of obtaining results of acceptable accuracy in as short a period of time in order to emphasize the interactive nature of the design process. Two case studies are considered to demonstrate the effectiveness of the prototype graphically driven reanalysis finite element technique. The finite element type considered is a plane stress four-node quadrilateral based on a homogenous, isotropic, linear elastic material. Each case study considered multiple redesigns. A combined approximation reanalysis method is used to solve each redesigned problem. The first case study considers a plate with a hole with the goal to determine the hole shape that will minimize the stress concentration. The second case study considers a support bracket. The goal is to design the cantilever portion of the bracket to have uniform strength and to minimize the stress concentration at the fillet.
- 25 August 2004
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 25 (5-6) , 409-419
Development of a finite element analysis tool for fixture design integrity verification and optimisation
- 25 August 2004
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 25 (5-6) , 409-419
Development of a finite element analysis tool for fixture design integrity verification and optimisation