Muhammad Waqas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Muhammad Waqas has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
Bengt Johansson
11 shared publications- Subram Mani Sarathy
Clean Energy Research Platform, Physical Sciences and Engineering (PSE) Division, King Abdullah University of Science and Technology (KAUST), Thuwal 23955-6900, Saudi Arabia
8 shared publications - Jean-Baptiste Masurier
King Abdullah University of Science & Technology
6 shared publications - Nimal Naser
National Renewable Energy Laboratory
4 shared publications - Eshan Singh
King Abdullah University of Science & Technology
3 shared publications - Kai Morganti
Saudi Aramco
3 shared publications
Latest Publications
- 1 January 2021
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 38 (4) , 5673-5683
An experimental and numerical investigation to characterize the low-temperature heat release in stoichiometric and lean combustion
- 1 January 2021
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 38 (4) , 5673-5683
An experimental and numerical investigation to characterize the low-temperature heat release in stoichiometric and lean combustion
- 24 September 2019
- Published by SAE International in SAE International Journal of Engines
- Vol. 12 (5) , 597-610
Characterization of Low Temperature Reactions in the Standard Cooperative Fuel Research (CFR) Engine
Many proposals for fuel rating in spark ignition (SI) engine have been suggested till date and still no consensus on this has been reached. The automobile industry is still using RON and MON tests for rating fuels, and still there exists a need to come up with new fuel rating systems. The fuel’s knocking tendency in SI engines is primarily governed by the end-gas autoignition. Another combustion mode, homogeneous charge compression ignition (HCCI), is also driven by autoignition of the complete charge inside the cylinder. Fundamentally, the combustion process in both combustion modes is driven by autoignition, and HCCI combustion mode can be used to understand the knocking behavior in SI engines. The lean combustion environment in HCCI mode provides a good platform to replicate the operating conditions of modern SI engines, which are operating at boosted pressures and low intake temperatures, and understanding of the fuel knocking behavior under such conditions is vital for achieving high-efficient engines. Therefore in this study, HCCI combustion will be used in the standard CFR engine to understand the autoignition behavior of the fuels for SI engines. For this purpose, three fuel blends were selected, which had the research octane number equal to 90. The standard CFR engine was operated with varying intake pressures and temperatures under HCCI combustion mode. The Lund-Chevron HCCI fuel number was used to rate the fuels and this was compared with RON and MON of the blends. It was found that HCCI combustion could be used to rate the fuels with the standard CFR engine with minor modifications to accommodate the boosted conditions without affecting the geometry and the flow inside the CFR engine. Low temperature reactions were observed and were correlated with the Lund-Chevron HCCI fuel numbers.
- 24 September 2019
- Published by SAE International in SAE International Journal of Engines
- Vol. 12 (5) , 597-610
Characterization of Low Temperature Reactions in the Standard Cooperative Fuel Research (CFR) Engine
Many proposals for fuel rating in spark ignition (SI) engine have been suggested till date and still no consensus on this has been reached. The automobile industry is still using RON and MON tests for rating fuels, and still there exists a need to come up with new fuel rating systems. The fuel’s knocking tendency in SI engines is primarily governed by the end-gas autoignition. Another combustion mode, homogeneous charge compression ignition (HCCI), is also driven by autoignition of the complete charge inside the cylinder. Fundamentally, the combustion process in both combustion modes is driven by autoignition, and HCCI combustion mode can be used to understand the knocking behavior in SI engines. The lean combustion environment in HCCI mode provides a good platform to replicate the operating conditions of modern SI engines, which are operating at boosted pressures and low intake temperatures, and understanding of the fuel knocking behavior under such conditions is vital for achieving high-efficient engines. Therefore in this study, HCCI combustion will be used in the standard CFR engine to understand the autoignition behavior of the fuels for SI engines. For this purpose, three fuel blends were selected, which had the research octane number equal to 90. The standard CFR engine was operated with varying intake pressures and temperatures under HCCI combustion mode. The Lund-Chevron HCCI fuel number was used to rate the fuels and this was compared with RON and MON of the blends. It was found that HCCI combustion could be used to rate the fuels with the standard CFR engine with minor modifications to accommodate the boosted conditions without affecting the geometry and the flow inside the CFR engine. Low temperature reactions were observed and were correlated with the Lund-Chevron HCCI fuel numbers.
- 10 September 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Combustion Behavior of n-Heptane, Isooctane, Toluene and Blends under HCCI Conditions in the Pressure-Temperature Diagram
Homogeneous charge compression ignition (HCCI) experiments were run with the aid of a Cooperative fuel research (CFR) engine, operating at 600 rpm and under very lean conditions (ϕ = 0.3). This study seeks to examine the combustion behavior of different fuels by finding the pressure-temperature (p-t) conditions that instigate the start of combustion, and the transition from low temperature combustion to principal combustion. The pressure-temperature diagram emphasizes p-t conditions according to their traces through the compression stroke. In each fuel tested, p-t traces were examined by a sweep of the intake temperature; and for each experimental point, combustion phasing was maintained at top dead center by adjusting the compression ratio of the engine. In addition to the p-t diagram, results were analyzed using a compression ratio-intake temperature diagram, which showed the compression ratio required with respect to intake temperature. Pure n-heptane, isooctane and toluene were investigated first. The results showed that these three fuels ignited in accordance with their octane number. The compression ratio-intake temperature diagram shows that the compression ratio decreased linearly with increased intake temperature. The p-t diagram reveals that the combustion of n-heptane always reacted with low temperature heat release, while toluene always reacted with one main combustion. However, isooctane behavior is subject to change. Isooctane combustion displayed two stages of combustion with low intake temperature, but when intake temperature increased, the low temperature heat release disappeared and only the main combustion remained. Finally, ignition delays computed from a constant volume model were compared to experimental ignitions; the results suggested that another model was required. Second, an octane number 90 primary reference fuel (PRF90) with different volume fractions of toluene was investigated. Results in the compression ratio-intake temperature showed that the compression ratio decreased linearly, while the intake temperature increased for PRF90 without toluene. When low fractions of toluene were added to PRF90 (from 5% to 30%), higher compression ratios were required and the trend became non-linear. A slight change in the compression ratio at low intake temperature was observed; while a greater change in the compression ratio at high intake temperature was required due to the presence of low temperature combustion. Finally, high fractions of toluene (higher than 40%) quenched the low temperature combustion and linear behavior was again achieved. The pressure temperature diagram also shows similar trends, with a transition of the low temperature combustion which moved in accordance with the fraction of toluene in PRF90.
- 10 September 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Combustion Behavior of n-Heptane, Isooctane, Toluene and Blends under HCCI Conditions in the Pressure-Temperature Diagram
Homogeneous charge compression ignition (HCCI) experiments were run with the aid of a Cooperative fuel research (CFR) engine, operating at 600 rpm and under very lean conditions (ϕ = 0.3). This study seeks to examine the combustion behavior of different fuels by finding the pressure-temperature (p-t) conditions that instigate the start of combustion, and the transition from low temperature combustion to principal combustion. The pressure-temperature diagram emphasizes p-t conditions according to their traces through the compression stroke. In each fuel tested, p-t traces were examined by a sweep of the intake temperature; and for each experimental point, combustion phasing was maintained at top dead center by adjusting the compression ratio of the engine. In addition to the p-t diagram, results were analyzed using a compression ratio-intake temperature diagram, which showed the compression ratio required with respect to intake temperature. Pure n-heptane, isooctane and toluene were investigated first. The results showed that these three fuels ignited in accordance with their octane number. The compression ratio-intake temperature diagram shows that the compression ratio decreased linearly with increased intake temperature. The p-t diagram reveals that the combustion of n-heptane always reacted with low temperature heat release, while toluene always reacted with one main combustion. However, isooctane behavior is subject to change. Isooctane combustion displayed two stages of combustion with low intake temperature, but when intake temperature increased, the low temperature heat release disappeared and only the main combustion remained. Finally, ignition delays computed from a constant volume model were compared to experimental ignitions; the results suggested that another model was required. Second, an octane number 90 primary reference fuel (PRF90) with different volume fractions of toluene was investigated. Results in the compression ratio-intake temperature showed that the compression ratio decreased linearly, while the intake temperature increased for PRF90 without toluene. When low fractions of toluene were added to PRF90 (from 5% to 30%), higher compression ratios were required and the trend became non-linear. A slight change in the compression ratio at low intake temperature was observed; while a greater change in the compression ratio at high intake temperature was required due to the presence of low temperature combustion. Finally, high fractions of toluene (higher than 40%) quenched the low temperature combustion and linear behavior was again achieved. The pressure temperature diagram also shows similar trends, with a transition of the low temperature combustion which moved in accordance with the fraction of toluene in PRF90.
- 10 September 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Blending Octane Number of 1-Butanol and Iso-Octane with Low Octane Fuels in HCCI Combustion Mode
Due to their physical and chemical properties, alcohols such as ethanol and methanol when blended with gasoline provide high anti-knock quality and hence efficient engines. However, there are few promising properties of 1-butanol similar to conventional gasoline which make it a favorable choice for internal combustion engines. Previously the author showed that by blending ethanol and methanol with low octane fuels, non-linear increase in the HCCI fuel number occurs in HCCI combustion mode. Very few studies have been conducted on the use of 1-butanol in HCCI combustion mode, therefore for this work, 1-butanol with a RON 96 was selected as the high octane fuel. Three low octane fuels with octane number close to 70 were used as a base fuel. Two of the low octane fuels are Fuels for Advanced Combustion Engines (FACE gasolines), more specifically FACE I and FACE J and also primary reference fuel (PRF 70) were selected. In addition, iso-octane, which has a different chemical structure than 1-butanol but an octane number (100) close to 1-butanol, was also selected as high octane fuel. A Cooperative Fuel Research (CFR) engine was used to conduct the experiments in HCCI combustion mode. HCCI fuel number was used for the octane rating similar to RON and MON in SI engine. 1-butanol and iso-octane were added in volume percentage 0, 5, 10, 15 and 20% to each of the base fuels. It was found that the increase of HCCI fuel number of 1-butanol was not linear with percentage added. For most of the operating conditions, non-linear synergistic blending behavior was observed when 1-butanol was blended with the three base fuels. The base fuel composition played a significant role for the blending octane number of 1-butanol. A weaker octane enhancement effect was observed when iso-octane was blended with the three base fuels.
- 10 September 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Blending Octane Number of 1-Butanol and Iso-Octane with Low Octane Fuels in HCCI Combustion Mode
Due to their physical and chemical properties, alcohols such as ethanol and methanol when blended with gasoline provide high anti-knock quality and hence efficient engines. However, there are few promising properties of 1-butanol similar to conventional gasoline which make it a favorable choice for internal combustion engines. Previously the author showed that by blending ethanol and methanol with low octane fuels, non-linear increase in the HCCI fuel number occurs in HCCI combustion mode. Very few studies have been conducted on the use of 1-butanol in HCCI combustion mode, therefore for this work, 1-butanol with a RON 96 was selected as the high octane fuel. Three low octane fuels with octane number close to 70 were used as a base fuel. Two of the low octane fuels are Fuels for Advanced Combustion Engines (FACE gasolines), more specifically FACE I and FACE J and also primary reference fuel (PRF 70) were selected. In addition, iso-octane, which has a different chemical structure than 1-butanol but an octane number (100) close to 1-butanol, was also selected as high octane fuel. A Cooperative Fuel Research (CFR) engine was used to conduct the experiments in HCCI combustion mode. HCCI fuel number was used for the octane rating similar to RON and MON in SI engine. 1-butanol and iso-octane were added in volume percentage 0, 5, 10, 15 and 20% to each of the base fuels. It was found that the increase of HCCI fuel number of 1-butanol was not linear with percentage added. For most of the operating conditions, non-linear synergistic blending behavior was observed when 1-butanol was blended with the three base fuels. The base fuel composition played a significant role for the blending octane number of 1-butanol. A weaker octane enhancement effect was observed when iso-octane was blended with the three base fuels.
- 3 April 2018
- Published by SAE International in SAE International Journal of Fuels and Lubricants
- Vol. 11 (4) , 459-468
Autoignition of Isooctane beyond RON and MON Conditions
The present study experimentally examines the low-temperature autoignition area of isooctane within the in-cylinder pressure-in-cylinder temperature map.Experiments were run with the help of a Cooperative Fuel Research (CFR) engine. The boundaries of this engine were extended so that experiments could be performed outside the domain delimited by research octane number (RON) and motor octane number (MON) traces. Since homogeneous charge compression ignition (HCCI) combustion is governed by kinetics, the rotation speed for all the experiments was set at 600 rpm to allow time for low-temperature heat release (LTHR). All the other parameters (intake pressure, intake temperature, compression ratio, and equivalence ratio) were scanned, such as the occurrence of isooctane combustion.The principal results showed that LTHR for isooctane occurs effortlessly under high intake pressure (1.3 bar) and low intake temperature (25 °C). Increasing the intake temperature leads to the loss of the LTHR and therefore to a smaller domain on the pressure-temperature trace. In such a case, the LTHR domain is restricted from 20 to 50 bar in pressure and from 600 to 850 K in temperature. By slightly decreasing the intake pressure, the LTHR domain remains unchanged, but the LTHR tends to disappear, and finally, at 1.0 bar, the LTHR domain ceases to exist. When the equivalence ratio is moved from 0.3 to 0.4, the LTHR domain is delimited in the same range of pressure and temperature, but the start of combustion occurs slightly earlier for the same pressure-temperature trace. Similar conclusions were drawn regarding the variation of both intake pressure and temperature, except that few LTHR points were observed under 1.0 bar intake.
- 3 April 2018
- Published by SAE International in SAE International Journal of Fuels and Lubricants
- Vol. 11 (4) , 459-468
Autoignition of Isooctane beyond RON and MON Conditions
The present study experimentally examines the low-temperature autoignition area of isooctane within the in-cylinder pressure-in-cylinder temperature map.Experiments were run with the help of a Cooperative Fuel Research (CFR) engine. The boundaries of this engine were extended so that experiments could be performed outside the domain delimited by research octane number (RON) and motor octane number (MON) traces. Since homogeneous charge compression ignition (HCCI) combustion is governed by kinetics, the rotation speed for all the experiments was set at 600 rpm to allow time for low-temperature heat release (LTHR). All the other parameters (intake pressure, intake temperature, compression ratio, and equivalence ratio) were scanned, such as the occurrence of isooctane combustion.The principal results showed that LTHR for isooctane occurs effortlessly under high intake pressure (1.3 bar) and low intake temperature (25 °C). Increasing the intake temperature leads to the loss of the LTHR and therefore to a smaller domain on the pressure-temperature trace. In such a case, the LTHR domain is restricted from 20 to 50 bar in pressure and from 600 to 850 K in temperature. By slightly decreasing the intake pressure, the LTHR domain remains unchanged, but the LTHR tends to disappear, and finally, at 1.0 bar, the LTHR domain ceases to exist. When the equivalence ratio is moved from 0.3 to 0.4, the LTHR domain is delimited in the same range of pressure and temperature, but the start of combustion occurs slightly earlier for the same pressure-temperature trace. Similar conclusions were drawn regarding the variation of both intake pressure and temperature, except that few LTHR points were observed under 1.0 bar intake.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Blending Octane Number of Toluene with Gasoline-like and PRF Fuels in HCCI Combustion Mode
Future internal combustion engines demand higher efficiency but progression towards this is limited by the phenomenon called knock. A possible solution for reaching high efficiency is Octane-on-Demand (OoD), which allows to customize the antiknock quality of a fuel through blending of high-octane fuel with a low octane fuel. Previous studies on Octane-on-Demand highlighted efficiency benefits depending on the combination of low octane fuel with high octane booster. The author recently published works with ethanol and methanol as high-octane fuels. The results of this work showed that the composition and octane number of the low octane fuel is significant for the blending octane number of both ethanol and methanol. This work focuses on toluene as the high octane fuel (RON 120). Aromatics offers anti-knock quality and with high octane number than alcohols, this work will address if toluene can provide higher octane enhancement. Our aim is to investigate the impact of three gasoline-like fuels and two Primary Reference Fuels (PRFs). More specifically, fuels are FACE (Fuels for Advanced Combustion Engines) I, FACE J, FACE A, PRF 70 and PRF 84. A CFR engine was used to conduct the experiments in HCCI mode. For this combustion mode, the engine operated at four specific conditions based on RON and MON conditions. The octane numbers corresponding to four HCCI numbers were obtained for toluene concentration of 0, 2, 5, 10, 15 and 20%. Results show that the blending octane number of toluene varies non-linearly and linearly with the increase in toluene concentration depending on the base fuel, experimental conditions and the concentration of toluene. As a result, the blending octane number can range from close to 150 with a small fraction of toluene to a number closer to that of toluene, 120, with larger fractions.
- 3 April 2018
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Blending Octane Number of Toluene with Gasoline-like and PRF Fuels in HCCI Combustion Mode
Future internal combustion engines demand higher efficiency but progression towards this is limited by the phenomenon called knock. A possible solution for reaching high efficiency is Octane-on-Demand (OoD), which allows to customize the antiknock quality of a fuel through blending of high-octane fuel with a low octane fuel. Previous studies on Octane-on-Demand highlighted efficiency benefits depending on the combination of low octane fuel with high octane booster. The author recently published works with ethanol and methanol as high-octane fuels. The results of this work showed that the composition and octane number of the low octane fuel is significant for the blending octane number of both ethanol and methanol. This work focuses on toluene as the high octane fuel (RON 120). Aromatics offers anti-knock quality and with high octane number than alcohols, this work will address if toluene can provide higher octane enhancement. Our aim is to investigate the impact of three gasoline-like fuels and two Primary Reference Fuels (PRFs). More specifically, fuels are FACE (Fuels for Advanced Combustion Engines) I, FACE J, FACE A, PRF 70 and PRF 84. A CFR engine was used to conduct the experiments in HCCI mode. For this combustion mode, the engine operated at four specific conditions based on RON and MON conditions. The octane numbers corresponding to four HCCI numbers were obtained for toluene concentration of 0, 2, 5, 10, 15 and 20%. Results show that the blending octane number of toluene varies non-linearly and linearly with the increase in toluene concentration depending on the base fuel, experimental conditions and the concentration of toluene. As a result, the blending octane number can range from close to 150 with a small fraction of toluene to a number closer to that of toluene, 120, with larger fractions.
- 8 October 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Blending Octane Number of Ethanol on a Volume and Molar Basis in SI and HCCI Combustion Modes
The blending behavior of ethanol in five different hydrocarbon base fuels with octane numbers of approximately 70 and 84 was examined under Spark-Ignited (SI) and Homogeneous Charge Compression Ignited (HCCI) operating conditions. The Blending octane number (BON) was used to characterize the blending behavior on both a volume and molar basis. Previous studies have shown that the blending behavior of ethanol generally follows several well-established rules. In particular, non-linear blending effects are generally observed on a volume basis (i.e. BON > RON or MON of pure ethanol; 108 and 89, respectively), while linear blending effects are generally observed on a molar basis (i.e. BON = RON or MON of pure ethanol). This work firstly demonstrates that the non-linear volumetric blending effects traditionally observed under SI operating conditions are also observed under HCCI operating conditions. In keeping with previous studies, the degree of this non-linearity is shown to be a function of the base fuel composition and octane number. By contrast, the molar blending approach is shown to behave differently depending on the chosen combustion mode, with some non-linearity observed under HCCI operating conditions (i.e. BON ≠ RON or MON of pure ethanol). This suggests that the well-established blending rules for SI operating conditions may not always be relevant to other combustion modes that operate with globally lean or diluted air-fuel mixtures. This has implications for the design of future fuel specifications.
- 8 October 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Blending Octane Number of Ethanol on a Volume and Molar Basis in SI and HCCI Combustion Modes
The blending behavior of ethanol in five different hydrocarbon base fuels with octane numbers of approximately 70 and 84 was examined under Spark-Ignited (SI) and Homogeneous Charge Compression Ignited (HCCI) operating conditions. The Blending octane number (BON) was used to characterize the blending behavior on both a volume and molar basis. Previous studies have shown that the blending behavior of ethanol generally follows several well-established rules. In particular, non-linear blending effects are generally observed on a volume basis (i.e. BON > RON or MON of pure ethanol; 108 and 89, respectively), while linear blending effects are generally observed on a molar basis (i.e. BON = RON or MON of pure ethanol). This work firstly demonstrates that the non-linear volumetric blending effects traditionally observed under SI operating conditions are also observed under HCCI operating conditions. In keeping with previous studies, the degree of this non-linearity is shown to be a function of the base fuel composition and octane number. By contrast, the molar blending approach is shown to behave differently depending on the chosen combustion mode, with some non-linearity observed under HCCI operating conditions (i.e. BON ≠ RON or MON of pure ethanol). This suggests that the well-established blending rules for SI operating conditions may not always be relevant to other combustion modes that operate with globally lean or diluted air-fuel mixtures. This has implications for the design of future fuel specifications.
- 4 September 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Blending Behavior of Ethanol with PRF 84 and FACE A Gasoline in HCCI Combustion Mmode
The blending of ethanol with PRF (Primary reference fuel) 84 was investigated and compared with FACE (Fuels for Advanced Combustion Engines) A gasoline surrogate which has a RON of 83.9. Previously, experiments were performed at four HCCI conditions but the chemical effect responsible for the non-linear blending behavior of ethanol with PRF 84 and FACE A was not understood. Hence, in this study the experimental measurements were simulated using zero-dimensional HCCI engine model with detailed chemistry in CHEMKIN PRO. Ethanol was used as an octane booster for the above two base fuels in volume concentration of 0%, 2%, 5% and 10%.The geometrical data and the intake valve closure conditions were used to match the simulated combustion phasing with the experiments. Low temperature heat release (LTHR) was detected by performing heat release analysis. LTHR formation depended on the base fuel type and the engine operating conditions suggesting that the base fuel composition has an important role in the formation of LTHR. The effect of ethanol on LTHR was explained by low temperature chemistry reactions and OH/HO2 evolution. A strong correlation of low temperature oxidation reactions of base fuels with ethanol was found to be responsible for the observed blending effects.
- 4 September 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Blending Behavior of Ethanol with PRF 84 and FACE A Gasoline in HCCI Combustion Mmode
The blending of ethanol with PRF (Primary reference fuel) 84 was investigated and compared with FACE (Fuels for Advanced Combustion Engines) A gasoline surrogate which has a RON of 83.9. Previously, experiments were performed at four HCCI conditions but the chemical effect responsible for the non-linear blending behavior of ethanol with PRF 84 and FACE A was not understood. Hence, in this study the experimental measurements were simulated using zero-dimensional HCCI engine model with detailed chemistry in CHEMKIN PRO. Ethanol was used as an octane booster for the above two base fuels in volume concentration of 0%, 2%, 5% and 10%.The geometrical data and the intake valve closure conditions were used to match the simulated combustion phasing with the experiments. Low temperature heat release (LTHR) was detected by performing heat release analysis. LTHR formation depended on the base fuel type and the engine operating conditions suggesting that the base fuel composition has an important role in the formation of LTHR. The effect of ethanol on LTHR was explained by low temperature chemistry reactions and OH/HO2 evolution. A strong correlation of low temperature oxidation reactions of base fuels with ethanol was found to be responsible for the observed blending effects.
- 28 March 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Evaluation of Anti-Knock Quality of Dicyclopentadiene-Gasoline Blends
Increasing the anti-knock quality of gasoline fuels can enable higher efficiency in spark ignition engines. In this study, the blending anti-knock quality of dicyclopentadiene (DCPD), a by-product of ethylene production from naphtha cracking, with various gasoline fuels is explored. The blends were tested in an ignition quality tester (IQT) and a modified cooperative fuel research (CFR) engine operating under homogenous charge compression ignition (HCCI) and knock limited spark advance (KLSA) conditions. Due to current fuel regulations, ethanol is widely used as a gasoline blending component in many markets. In addition, ethanol is widely used as a fuel and literature verifying its performance. Moreover, because ethanol exhibits synergistic effects, the test results of DCPD-gasoline blends were compared to those of ethanol-gasoline blends. The experiments conducted in this work enabled the screening of DCPD auto-ignition characteristics across a range of combustion modes. The synergistic blending nature of DCPD was apparent and appeared to be greater than that of ethanol. The data presented suggests that DCPD has the potential to be a high octane blending component in gasoline; one which can substitute alkylates, isomerates, reformates, and oxygenates.
- 28 March 2017
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Evaluation of Anti-Knock Quality of Dicyclopentadiene-Gasoline Blends
Increasing the anti-knock quality of gasoline fuels can enable higher efficiency in spark ignition engines. In this study, the blending anti-knock quality of dicyclopentadiene (DCPD), a by-product of ethylene production from naphtha cracking, with various gasoline fuels is explored. The blends were tested in an ignition quality tester (IQT) and a modified cooperative fuel research (CFR) engine operating under homogenous charge compression ignition (HCCI) and knock limited spark advance (KLSA) conditions. Due to current fuel regulations, ethanol is widely used as a gasoline blending component in many markets. In addition, ethanol is widely used as a fuel and literature verifying its performance. Moreover, because ethanol exhibits synergistic effects, the test results of DCPD-gasoline blends were compared to those of ethanol-gasoline blends. The experiments conducted in this work enabled the screening of DCPD auto-ignition characteristics across a range of combustion modes. The synergistic blending nature of DCPD was apparent and appeared to be greater than that of ethanol. The data presented suggests that DCPD has the potential to be a high octane blending component in gasoline; one which can substitute alkylates, isomerates, reformates, and oxygenates.