Gnaniar Kalusuraman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Gnaniar Kalusuraman has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Irullappasamy Siva
Kalasalingam Academy of Research and Education
5 shared publications - Sundaresan Thirumalai Kumaran
Department of Mechanical Engineering, PSG Institute of Technology and Applied Research, Coimbatore 641062, Tamil Nadu, India
4 shared publications J.T. Winowlin Jappes
3 shared publications- Jayavelu Udaya Prakash
Department of Mechanical Engineering, Vel Tech Rangarajan Dr Sagunthala R&D Institute of science and technology, Chennai, India
3 shared publications - Palani Sivaprakasam
Department of Mechanical Engineering, College of Engineering, Addis Ababa Science and Technology University, Addis Ababa, Ethiopia
3 shared publications - Senthilkumar Krishnasamy
Department of Mechanical Engineering, PSG Institute of Technology and Applied Research, Coimbatore 641062, India
3 shared publications
Latest Publications
- 2 May 2025
- Published by BioResources in BioResources
- Vol. 20 (3)
Impact of drying temperature on the physicochemical and functional properties of butterfly pea flower powder
Butterfly pea flower (BPF) powder, which is rich in bioactive compounds, was evaluated for the impact of various drying methods on its solubility, physical properties, and chemical composition. Four drying methods were used: thermal drying at 50 °C, 60 °C, 70 °C, and natural sun drying. The powders were assessed for solubility time, hygroscopicity, density, flowability, and chemical stability using scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FTIR). Solubility times ranged from 148 to 162 s, with no significant differences. The 70 °C dried sample (Sample C) had the fastest dissolution rate and highest hygroscopicity. Total phenolic and anthocyanin contents increased with temperature, peaking in sun-dried samples (Sample D). Density measurements showed Sample C had the highest bulk density and optimal flowability, while Sample D had superior water holding capacity. The SEM analysis revealed morphological differences, with Sample A showing a smooth surface and Sample C exhibiting significant particle disintegration. The XRD analysis showed that Sample C had the highest crystallinity. The FTIR analysis confirmed the stability of key functional groups, with sun-dried samples retaining phenolic compounds. These findings suggest drying methods can optimize BPF powder’s properties, enhancing its bioactivity for health applications.
- 2 May 2025
- Published by BioResources in BioResources
- Vol. 20 (3)
Impact of drying temperature on the physicochemical and functional properties of butterfly pea flower powder
Butterfly pea flower (BPF) powder, which is rich in bioactive compounds, was evaluated for the impact of various drying methods on its solubility, physical properties, and chemical composition. Four drying methods were used: thermal drying at 50 °C, 60 °C, 70 °C, and natural sun drying. The powders were assessed for solubility time, hygroscopicity, density, flowability, and chemical stability using scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FTIR). Solubility times ranged from 148 to 162 s, with no significant differences. The 70 °C dried sample (Sample C) had the fastest dissolution rate and highest hygroscopicity. Total phenolic and anthocyanin contents increased with temperature, peaking in sun-dried samples (Sample D). Density measurements showed Sample C had the highest bulk density and optimal flowability, while Sample D had superior water holding capacity. The SEM analysis revealed morphological differences, with Sample A showing a smooth surface and Sample C exhibiting significant particle disintegration. The XRD analysis showed that Sample C had the highest crystallinity. The FTIR analysis confirmed the stability of key functional groups, with sun-dried samples retaining phenolic compounds. These findings suggest drying methods can optimize BPF powder’s properties, enhancing its bioactivity for health applications.
- 2 May 2025
- Published by BioResources in BioResources
- Vol. 20 (3)
Extending tomato freshness: The role of aloe vera gel in reducing post-harvest losses
Tomatoes are widely consumed but highly perishable due to their rapid respiration and delicate skin, causing significant post-harvest losses. Sustainable preservation is essential to maintain quality and reduce food waste. This study investigated aloe vera gel (AVG) as a natural, edible coating to extend tomato shelf life. Tomatoes at the pink ripening stage were coated with AVG for 3 and 6 minutes, then stored at 10 °C and 85% relative humidity for 16 days. The physicochemical traits pH, firmness, moisture content, total soluble solids (TSS), and microbial load were assessed every four days. AVG coatings slowed declines in pH, firmness, and moisture content compared to controls (p<0.05). Non-coated tomatoes dropped from pH 4.48 to 2.87, while 3- and 6-minute coated samples retained higher pH (3.28 and 3.65). Firmness fell to 0.56 kg/cm² in controls, but coated samples retained 1.18 and 1.50 kg/cm². Coated tomatoes had higher final moisture (78.35 to 80.25%) than controls (70.45%) and less weight loss (29.55 to 30.26 g vs. 28.11 g). TSS levels remained higher in coated tomatoes (3.10 to 3.40 °Brix vs. 2.40 °Brix), with lower microbial counts (2.95 and 2.16 vs. 4.24 log CFU/g). These results support AVG as an effective, eco-friendly method for preserving tomato quality.
- 2 May 2025
- Published by BioResources in BioResources
- Vol. 20 (3)
Extending tomato freshness: The role of aloe vera gel in reducing post-harvest losses
Tomatoes are widely consumed but highly perishable due to their rapid respiration and delicate skin, causing significant post-harvest losses. Sustainable preservation is essential to maintain quality and reduce food waste. This study investigated aloe vera gel (AVG) as a natural, edible coating to extend tomato shelf life. Tomatoes at the pink ripening stage were coated with AVG for 3 and 6 minutes, then stored at 10 °C and 85% relative humidity for 16 days. The physicochemical traits pH, firmness, moisture content, total soluble solids (TSS), and microbial load were assessed every four days. AVG coatings slowed declines in pH, firmness, and moisture content compared to controls (p<0.05). Non-coated tomatoes dropped from pH 4.48 to 2.87, while 3- and 6-minute coated samples retained higher pH (3.28 and 3.65). Firmness fell to 0.56 kg/cm² in controls, but coated samples retained 1.18 and 1.50 kg/cm². Coated tomatoes had higher final moisture (78.35 to 80.25%) than controls (70.45%) and less weight loss (29.55 to 30.26 g vs. 28.11 g). TSS levels remained higher in coated tomatoes (3.10 to 3.40 °Brix vs. 2.40 °Brix), with lower microbial counts (2.95 and 2.16 vs. 4.24 log CFU/g). These results support AVG as an effective, eco-friendly method for preserving tomato quality.
- 2 February 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 31 (09)
SOLID PARTICLE AIRJET EROSION AND CORROSION BEHAVIOR OF AA6063 ALUMINUM ALLOY
Aluminum alloy 6063 has excellent mechanical properties and it is used in automotive industries. This research focuses on solid particle airjet erosion behavior in different input parameters such as mass flow rate of 2, 3, and 4[ ]gm/min, impingement angle of 30∘, 60∘, and 90∘ and erodent velocity of 100, 150, and 200[ ]m/s. The alumina erodent is mixed with an airjet which acts as an impingement fluid jet. Taguchi was utilized for investigating the influence of the process parameter on erosion rate, and ANOVA was performed to evaluate the parameter contribution. The impingement velocity is the most significant parameter to reduce the erosion rate rather than the impingement angle and the mass flow rate. The increase in velocity of the impingement fluid jet accelerates the erosion rate due to the high kinetic energy impact. The desirability approach is used to optimize the input parameters. At 99% confidence levels, the models were considered significant. The importance of the factor is increased by a reduced p-value. From the overall analysis, the optimum conditions of solid particle airjet erosion are impingement angle of 90∘, erodent velocity of 100[ ]m/s and erodent flow rate of 2[ ]gm/min. Utilizing the cyclic sweep approach, corrosion behavior and NaCl solution are involved in the test of AA6063. As the corrosion current density increased, the corrosion potential became more positive.
- 2 February 2024
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 31 (09)
SOLID PARTICLE AIRJET EROSION AND CORROSION BEHAVIOR OF AA6063 ALUMINUM ALLOY
Aluminum alloy 6063 has excellent mechanical properties and it is used in automotive industries. This research focuses on solid particle airjet erosion behavior in different input parameters such as mass flow rate of 2, 3, and 4[ ]gm/min, impingement angle of 30∘, 60∘, and 90∘ and erodent velocity of 100, 150, and 200[ ]m/s. The alumina erodent is mixed with an airjet which acts as an impingement fluid jet. Taguchi was utilized for investigating the influence of the process parameter on erosion rate, and ANOVA was performed to evaluate the parameter contribution. The impingement velocity is the most significant parameter to reduce the erosion rate rather than the impingement angle and the mass flow rate. The increase in velocity of the impingement fluid jet accelerates the erosion rate due to the high kinetic energy impact. The desirability approach is used to optimize the input parameters. At 99% confidence levels, the models were considered significant. The importance of the factor is increased by a reduced p-value. From the overall analysis, the optimum conditions of solid particle airjet erosion are impingement angle of 90∘, erodent velocity of 100[ ]m/s and erodent flow rate of 2[ ]gm/min. Utilizing the cyclic sweep approach, corrosion behavior and NaCl solution are involved in the test of AA6063. As the corrosion current density increased, the corrosion potential became more positive.
- Open Access
- 1 January 2024
- Published by European Alliance for Innovation n.o.
Compression Properties of 3D Printed Honeycomb and Re-Entrant Sandwich Core Materials
In the research, various thermoplastic filaments were used to create honeycomb (cellular) and re-entrant (auxetic) structures using a 3D printer of the FDM type, and their compression properties were examined. The thermoplastic polymers PP, ABS, PLA, and PA were used to create the samples. The samples' stress-strain relationships were established after they were compressed quasi-statically in both edgewise and flatwise directions. Digital-image correlation was used to measure full-field displacements on the sample surfaces and evaluate the behavior of compressive deformation in the elastic and plastic regimes up to densification. Re-entrant type auxetic core components were shown to have higher compression failure stresses than cellular honeycomb core components through compression tests in flatwise and edgewise directions. The honeycomb cores have higher energy absorption for the same polymer types, according to the stress-strain curves of the re-entrant core failure.
- 1 January 2024
- Published by European Alliance for Innovation n.o.
Open AccessCompression Properties of 3D Printed Honeycomb and Re-Entrant Sandwich Core Materials
In the research, various thermoplastic filaments were used to create honeycomb (cellular) and re-entrant (auxetic) structures using a 3D printer of the FDM type, and their compression properties were examined. The thermoplastic polymers PP, ABS, PLA, and PA were used to create the samples. The samples' stress-strain relationships were established after they were compressed quasi-statically in both edgewise and flatwise directions. Digital-image correlation was used to measure full-field displacements on the sample surfaces and evaluate the behavior of compressive deformation in the elastic and plastic regimes up to densification. Re-entrant type auxetic core components were shown to have higher compression failure stresses than cellular honeycomb core components through compression tests in flatwise and edgewise directions. The honeycomb cores have higher energy absorption for the same polymer types, according to the stress-strain curves of the re-entrant core failure.
- Open Access
- 21 December 2022
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 20 (1)
Vibration Studies on Fiber Reinforced Composites – a Review
Fiber reinforced composites materials have been much more attention in the materials system by the researchers since their unique performance in various structural applications. The addition of fiber and various chemical treatments produces the best mechanical properties of the composite material. However, several authors have described the working mechanism in mechanical composites. Recently researchers have started to investigate the free vibrational behavior of the composites and to find the suitable applications in industry. It is indeed important to represent the vibrational response of the fiber reinforced composites (FRC) toward the anti-vibration applications. Thus, an attempt was made to review the vibration behaviors on natural fiber, synthetic fiber, and filler incorporated natural/synthetic fiber composites. Discussions on the comparison of the natural frequency and damping ratio of various composites bring comprehensive knowledge on vibrational behaviors of various fiber reinforced composites.
- 21 December 2022
- Published by Taylor & Francis in Journal of Natural Fibers
- Vol. 20 (1)
Open AccessVibration Studies on Fiber Reinforced Composites – a Review
Fiber reinforced composites materials have been much more attention in the materials system by the researchers since their unique performance in various structural applications. The addition of fiber and various chemical treatments produces the best mechanical properties of the composite material. However, several authors have described the working mechanism in mechanical composites. Recently researchers have started to investigate the free vibrational behavior of the composites and to find the suitable applications in industry. It is indeed important to represent the vibrational response of the fiber reinforced composites (FRC) toward the anti-vibration applications. Thus, an attempt was made to review the vibration behaviors on natural fiber, synthetic fiber, and filler incorporated natural/synthetic fiber composites. Discussions on the comparison of the natural frequency and damping ratio of various composites bring comprehensive knowledge on vibrational behaviors of various fiber reinforced composites.
- Open Access
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Tribological Characteristics of GCI‐EN31 Steel Surface Contact with Dry Sliding Condition
Grey cast iron (GCI) and steel contact surface application is an inevitable component and provides good wear resistance in several applications, not only in automobiles. Grey cast iron consists of a predominantly pearlitic/ferrite matrix or both with graphite flakes. The majority of previous research works were based on three different types of wear regimes. The wear regimes enumerate the wear track morphology, wear rate, and COF of the respective application. In this research work, dry sliding wear properties of GCI and EN31 pins were examined with different sliding parameters using pin on disc wear test. The weight loss, coefficient of frictions, and surface morphology were considered for experimental analysis. Due to the transfer of wear debris from the GCI disc, the counter steel pin surface experienced a progressive reduction in wear with increasing speed and load. With 30 N and 45 N contact loads and sliding speeds up to 1 m/sec, the GCI shows marginally positive wear. The surface textures were analyzed with the help of SEM and a surface roughness tester.
- 1 January 2022
- Published by Wiley in Journal of Nanomaterials
- Vol. 2022 (1)
Open AccessTribological Characteristics of GCI‐EN31 Steel Surface Contact with Dry Sliding Condition
Grey cast iron (GCI) and steel contact surface application is an inevitable component and provides good wear resistance in several applications, not only in automobiles. Grey cast iron consists of a predominantly pearlitic/ferrite matrix or both with graphite flakes. The majority of previous research works were based on three different types of wear regimes. The wear regimes enumerate the wear track morphology, wear rate, and COF of the respective application. In this research work, dry sliding wear properties of GCI and EN31 pins were examined with different sliding parameters using pin on disc wear test. The weight loss, coefficient of frictions, and surface morphology were considered for experimental analysis. Due to the transfer of wear debris from the GCI disc, the counter steel pin surface experienced a progressive reduction in wear with increasing speed and load. With 30 N and 45 N contact loads and sliding speeds up to 1 m/sec, the GCI shows marginally positive wear. The surface textures were analyzed with the help of SEM and a surface roughness tester.
- RetractedOpen Access
- 13 December 2021
- Published by Wiley in Journal of Nanomaterials
- Vol. 2021, 1-10
Wire Electrical Discharge Machining (WEDM) of Hybrid Composites (Al-Si12/B4C/Fly Ash)
The present study looks into the effect of WEDM process parameters on the material removal rate (MRR) and surface roughness (SR) responses when machining hybrid composites (Al-Si12/boron carbide/fly ash) using the Taguchi technique. Fly ash and boron carbide (B4C) particles were used for reinforcement (3, 6, and 9 by weight), and aluminium alloy (Al-Si12) was used as a matrix material. ANOVA was used to find out the importance of machining factors that affect the quality features of the WEDM process, as well as the relative role of input parameters in determining the WEDM process responses. The greatest impact on the response is finalised by the signal-to-noise (S/N) ratio response analysis. However, as a last step, a confirmation experiment with the best combination was carried out to predict and validate the accuracy of the observed values. As the pulse on time and reinforcement increases, MRR also increases. As the gap voltage, wire feed, and pulse off time decrease, it increases. SR is increased by increasing the gap voltage, pulse on time, and pulse off time, wire feed, and reinforcement. The maximum MRR of 38.01mm3/min and the minimum SR of 3.24μm were obtained using optimal machining conditions.
- 13 December 2021
- Published by Wiley in Journal of Nanomaterials
- Vol. 2021, 1-10
RetractedOpen AccessWire Electrical Discharge Machining (WEDM) of Hybrid Composites (Al-Si12/B4C/Fly Ash)
The present study looks into the effect of WEDM process parameters on the material removal rate (MRR) and surface roughness (SR) responses when machining hybrid composites (Al-Si12/boron carbide/fly ash) using the Taguchi technique. Fly ash and boron carbide (B4C) particles were used for reinforcement (3, 6, and 9 by weight), and aluminium alloy (Al-Si12) was used as a matrix material. ANOVA was used to find out the importance of machining factors that affect the quality features of the WEDM process, as well as the relative role of input parameters in determining the WEDM process responses. The greatest impact on the response is finalised by the signal-to-noise (S/N) ratio response analysis. However, as a last step, a confirmation experiment with the best combination was carried out to predict and validate the accuracy of the observed values. As the pulse on time and reinforcement increases, MRR also increases. As the gap voltage, wire feed, and pulse off time decrease, it increases. SR is increased by increasing the gap voltage, pulse on time, and pulse off time, wire feed, and reinforcement. The maximum MRR of 38.01mm3/min and the minimum SR of 3.24μm were obtained using optimal machining conditions.
- RetractedOpen Access
- 14 October 2021
- Published by Wiley in Journal of Nanomaterials
- Vol. 2021, 1-9
Tribological Behavior and Surface Characterization of Gray Cast Iron-EN31 Steel under Lubricated Sliding Conditions
This research investigates the tribological behavior of gray cast iron against EN31 steel under lubricated conditions. The most typical lubricated sliding phenomena are the reduction of wear on both the sliding surfaces and any one of the critical surfaces. Static and hydrodynamic wear can be reduced based on fluid properties or the accessibility of fluid between the surfaces. The oil’s viscosity or content of the hydrocarbon and additives present in the oil plays a major role in controlling the wear of reciprocating surfaces. Therefore, this research work focused on metal-to-metal contact wear under the influence of lubricating oil (40 pride oil). The Taguchi method was used to select the sliding parameter combinations. Lubricated sliding resulted in a relatively reduced order of friction coefficient, attributable to better load distribution due to the formation of the lubricant film.
- 14 October 2021
- Published by Wiley in Journal of Nanomaterials
- Vol. 2021, 1-9
RetractedOpen AccessTribological Behavior and Surface Characterization of Gray Cast Iron-EN31 Steel under Lubricated Sliding Conditions
This research investigates the tribological behavior of gray cast iron against EN31 steel under lubricated conditions. The most typical lubricated sliding phenomena are the reduction of wear on both the sliding surfaces and any one of the critical surfaces. Static and hydrodynamic wear can be reduced based on fluid properties or the accessibility of fluid between the surfaces. The oil’s viscosity or content of the hydrocarbon and additives present in the oil plays a major role in controlling the wear of reciprocating surfaces. Therefore, this research work focused on metal-to-metal contact wear under the influence of lubricating oil (40 pride oil). The Taguchi method was used to select the sliding parameter combinations. Lubricated sliding resulted in a relatively reduced order of friction coefficient, attributable to better load distribution due to the formation of the lubricant film.
- 1 December 2019
- Published by Elsevier in Measurement
- Vol. 148
Use of waste copper slag filled jute fiber reinforced composites for effective erosion prevention
- 1 December 2019
- Published by Elsevier in Measurement
- Vol. 148
Use of waste copper slag filled jute fiber reinforced composites for effective erosion prevention
- 24 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (9) , 095106
Evaluation of surface pre-treatments on the surface characteristics modifications in sponge gourd (Luffa Cylindrica) fibers
- 24 July 2019
- Published by IOP Publishing in Materials Research Express
- Vol. 6 (9) , 095106
Evaluation of surface pre-treatments on the surface characteristics modifications in sponge gourd (Luffa Cylindrica) fibers