MWMichael Wensing

Michael Wensing

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Michael Wensing has a total of 151 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Characterization of preferential evaporation in binary ethanol-isooctane sprays: 2D droplet size and volume fraction measurements

    by Benjamin W. Klevansky, Bastian Lehnert, Michael Wensing, Florian J. Bauer, Stefan Will

    Understanding preferential evaporation in multi-component fuel sprays is critical for optimizing combustion efficiency and reducing emissions in internal combustion engines. This study focuses on the development of a novel approach that allows for the simultanous detailed characterization of the Sauter Mean Diameter (SMD) and relative ethanol/isooctane volume fraction to elucidate the mechanisms governing preferential evaporation in binary fuel mixtures. This is achieved by combining Planar Droplet Sizing (PDS), a technique based on the ratio between the laser-induced fluorescence (LIF) signal of Nile red-doped fuel and the elastic scattering signal, with a two-color-LIF approach. As Nile red is a solvatochromic dye, i.e., it exhibits a shift in its fluorescence signal with changes in solvent polarity and temperature, the mole fraction of ethanol and isooctane in the spray can be determined, if the spray temperature is known. We performed extensive calibration on various Nile red-doped fuel mixtures in a heated cuvette, as well as in a droplet generator. Further, we minimized morphology-dependent resonance (MDR) effects in the LIF signal of the spray by the selection of spectral filters designed to cover all measured temperatures and concentrations. We found that in the ethanol spray temperatures decrease toward the spray edge. For the fuel-mixed samples, this coincides with a smaller overall SMD and a shift in the ethanol volume fraction in this region.

  • Open Access

    Impact of polarization and detection angle on Mie scattering signals for planar droplet sizing

    by B. W. Klevansky, Y. N. Mishra, B. L. Lehnert, M. Wensing, F. J. Bauer, S. Will

    The planar droplet sizing (PDS) method for determining the droplet diameter from the ratio of laser-induced fluorescence (LIF) and Mie scattering signal (Mie) has been extensively applied for right-angle scattering detection. The present work consists of a parametrical study of the Mie signal dependency on the scattering angle and polarization, as well as further experimental investigations in single droplets to ultimately improve the intensity fluctuation characteristics of the signal through a favorable experimental arrangement. Finally, we investigated how these findings impact droplet sizing in a spray on a shot-to-shot basis, as well as averaged across a dataset, via microscopic and macroscopic spray measurements. In the parametrical study, we found that horizontally polarized incident light results in a higher degree of Mie signal fluctuation than vertically polarized incident light at a scattering angle of $$\Theta ={90}{^\circ }$$ Θ = 90 ∘ , whereas the reduction to $$\Theta = {60}{^\circ }$$ Θ = 60 ∘ resulted in the exact opposite observation. Furthermore, the reduction from $$\Theta = {90}{^\circ }$$ Θ = 90 ∘ to $$\Theta = {60}{^\circ }$$ Θ = 60 ∘ resulted in an overall improvement to the $$D^2$$ D 2 -dependency and signal fluctuation of the Mie signal. We observed the effects shown in the parametric study in the experimental droplet measurements. For instance, when observing single droplets, the change from $$\Theta = {90}{^\circ }$$ Θ = 90 ∘ to $$\Theta = {60}{^\circ }$$ Θ = 60 ∘ resulted in a reduction in signal fluctuation by 46.1% and 17.6% for horizontally and vertically polarized incident light, respectively. An implementation into a spray setup yielded reduced shot-to-shot sizing deviations and closer adherence to the microscopically measured diameter when averaged across the dataset. Graphical


  • Open Access

    Effects of liquid properties on atomization and spray characteristics studied by planar two-photon fluorescence

    by Hannah Ulrich, Bastian Lehnert, Diego Guénot, Kristoffer Svendsen, Olle Lundh, Michael Wensing, Edouard Berrocal, Lars Zigan

    In this work, planar two-photon laser-induced fluorescence (2p-LIF) is applied for the first time to analyze the fluid dependent spray structure and atomization behavior of water and ethanol in a quantitative way. A commercial six-hole DISI (Direct-Injection Spark-Ignition) injector was studied at different injection pressures, operated with liquids containing the LIF dye fluorescein. Specifically for DISI-injectors, the fluid-dependent atomization is very complex and not fully understood due to the cavitating, turbulent nozzle flow that dominates the spray formation. Optical access and analysis of the near-nozzle spray are often challenging due to multiple light scattering in dense regions which is reduced by 2p-LIF measurements using a femtosecond laser. This allows high-contrast spray imaging close to the nozzle, resulting in an improved identification of single liquid structures of the spray. Thus, a higher accuracy of sizing is possible. Compared to water, the ethanol spray shape shows increased cone angles in the nozzle near-field of about 6%, which cannot be explained by classical atomization theory based on aerodynamic breakup. The larger cone angle of ethanol was attributed to its larger viscosity, which could decelerate the flow at the wall of the injection hole, affecting the velocity profile of the emerging jet. The atomization shows a main jet breakup distance of 7–10 mm in which the structure sizes decreased drastically, specifically for water. For the size of the liquid structures in the near-nozzle region, which show dimensions of about 80–130 μm, ethanol exhibited about 2% smaller Feret's diameters than water for the tested time steps at 20 MPa. This effect is even more distinct for other injection pressures and positions at a further distance to the injector. For all investigated conditions and measurement positions downstream of the nozzle, ethanol showed on average about 24% smaller structures compared to the water spray. Although this trend is in accordance with the classical atomization theory based on the aerodynamic breakup mechanism, other effects, such as cavitation and nozzle-flow induced breakup, contribute to this behavior.


  • MIXTURE FORMATION ANALYSIS OF POLYOXYMETHYLENETHER INJECTION

    by Andreas Peter, B. Siewert, S. Riess, L. Strauss, C. Pastoetter, Michael Wensing

    Polyoxymethylenether (OME) is a promising fuel for CO2 reduction and a prospective change in the transportation sector. To see the effects of different fuel properties on mass flow rate and mixture formation, OME 3, OME 4, and a mixture of OME 3 and OME 4 (called OME Mix) are compared to European standard diesel fuel. They are investigated for a passenger car and two different commercial vehicle injectors with different nozzle hole diameters at engine relevant conditions of 5 MPa ambient pressure and 873 K ambient temperature. Mass flow rate measurements and optical measurement techniques like Mie scattering and Schlieren imaging are applied feeding the spray model of Musculus and Kattke to investigate the mixture formation. Additionally, a hydraulic and a computational fluid dynamic simulation of the internal nozzle flow are conducted to derive the fuel influence on the needle motion. The results show a strong influence of OME on the mass flow rate development via the correlated needle motion for commercial vehicle nozzle sizes. Depending on the fuel properties, the mass flow rate of OME is retarded in comparison to diesel under equal boundary conditions. The fuel-dependent needle opening impresses different initial momentum fluxes onto the spray. This hydraulic difference cannot be compensated in the upstream flow whereas the stream outside the hole follows the classical momentum conservation. For passenger car nozzle sizes the differences in mass flow rate and needle motion between OME and diesel fuel are not that distinctive, which lead to less deviations of the initially momentum fluxes.


  • Modeling the Pilot Injection and the Ignition Process of a Dual Fuel Injector with Experimental Data from a Combustion Chamber Using Detailed Reaction Kinetics

    by Jens Frühhaber, Andreas Peter, Sebastian Schuh, Thomas Lauer, Michael Wensing, Franz Winter, Peter Priesching, Klaus Pachler

    The introduction of the so called Emission Controlled Areas within the IMO Tier III legislation forces manufacturers of maritime propulsion systems to adherence to stringent emission thresholds. Dual fuel combustion, which is characterized by the injection of a small amount of fuel oil to ignite a premixed natural gas air mixture, constitutes an option to meet this target. At high diesel substitution rates and very short pilot injection events, the injector is operated in the ballistic regime. This influences spray penetration, mixture formation and ignition behavior. In the present work, a seven-hole dual fuel injector was measured in a combustion chamber to provide data for the generation of a CFD model using the commercial code AVL FIRE®. The liquid and the vapor phase of the fuel spray were quantified by Mie-scattering and Schlieren-imaging technique for different chamber conditions. Based on the measured spray characteristics, a methodology was developed to imprint a velocity profile to the initial droplets in the CFD model, to depict the spray penetration for small injection durations. To characterize the ignition process and the flame propagation, measurements of the OH* emission and the natural luminosity of the flame were carried out. A detailed reaction mechanism, which is able to predict both diesel and dual fuel combustion, was integrated in the CFD model. The ignition delay was fitted to the experimental data by adapting the reaction mechanism for different chamber temperatures. The influence of the presence of natural gas on the ignition behavior was validated using data from a rapid compression machine. Even for low temperatures and high pressures, similar to the start of injection under engine operating conditions, a good correlation could be achieved. The developed knowledge will be transferred to an engine model to investigate the limits of dual fuel combustion processes.


  • Characterizing Spray Propagation of GDI Injectors under Crossflow Conditions

    by Richard Welss, Sebastian Bornschlegel, Michael Wensing

    In DISI engines spray distribution and atomization directly influence mixture formation, the quality of combustion and the resulting emissions. Constant Volume Chambers (CVC) are commonly used to characterize sprays of gasoline injectors. The CVCs provide good optical access but the flow condition of the engine cannot be reproduced. Optically accessible engines in contrast deliver realistic flow conditions but have restricted optical access. In former investigations we compared the spray propagation of different injectors in constant volume chambers and in optical accessible engines. These results showed a clear difference of the spray propagation in the CVC and the engine, especially at high charge motion conditions in the engine. To find an appropriate way to investigate the impact of different charge motion a flow channel was built with adjustable crossflow velocities from 5-50 m/s. The spray propagation during the injection process was measured with high-speed shadowgraphy. Two main parameters are introduced to describe the crossflow stability. The location of the intensity center represents the global spray deflection. The second parameter is the ratio between the areas of high and low optical spray density to express the spray “blow-out” under crossflow conditions. Five different injectors were investigated at injection pressures between 100 bar and 170 bar to determine their stability and behavior under crossflow conditions. The results show a clear dependence of the spray propagation on crossflow velocities. With increasing injection pressure the stability against crossflow is increasing. Furthermore, the injectors show different behavior at the same conditions due to their different nozzle designs.


  • A simplified model for a diesel spray

    by Simon Marčič, Milan Marčič, Michael Wensing, Thomas Vogel, Zdravko Praunseis


  • Light sheet fluorescence microscopic imaging for the primary breakup of diesel and gasoline sprays with real-world fuels

    by Alexander Durst, Michael Wensing, Edouard Berrocal

    This paper describes the adaptation of the laser-induced fluorescence measurement technique for the investigation of the primary breakup of modern diesel and gasoline direct injection sprays. To investigate the primary breakup, a microscopic technique is required, and with the help of special tracer dyes, a high fluorescence signal can be achieved in the visible range of the electromagnetic spectrum, resulting in good image quality with a nonintensified camera. Besides the optimization of the optical setup for the microscopic field of view, different tracer dyes are compared, and their solubility and fluorescence are tested in the desired surrogate and real-world fuels. As a tracer, the phenoxazine dye Nile Red was found to provide sufficient solubility in alkanes as well as suitable emission and excitation spectrum for the use of the second-harmonic frequency of a Nd:YAG laser (532 nm). The good quantum efficiency delivered by Nile Red also meant that single-shot images clearly showing spray structures in regions measuring up to 3 mm by 3 mm around the nozzle outlet could be recorded. Compared to relatively easy shadowgraph techniques and complex and costly x-ray synchrotron measurements, light sheet fluorescence microscopic imaging is not overly complex yet delivers excellent data on spray structures as well as qualitative fuel distribution.


  • Multi-hole gasoline direct injection:In-nozzle flow and primary breakup investigated in transparent nozzlesand with X-ray

    by Sebastian Bornschlegel, Chris Conrad, Alexander Durst, Jin Wang, Michael Wensing

    The contribution describes the flow field inside modern gasoline direct-injection nozzles and sprays. Starting from the internal nozzle flow, results from transparent real-size nozzles are shown, where a significant vapor fraction even for cold fuel conditions is proven. Based on vapor fraction inside the nozzle, evidence for (super-)sonic flow conditions inside the nozzle is shown. The nozzle outlet velocity is determined by means of X-ray structure tracking velocimetry, which is a very powerful measurement technique to gain access to the very dense spray at the nozzle outlet. The X-ray velocities are compared to values that are determined by means of optical—phase Doppler anemometry/laser Doppler anemometry and Schlieren imaging—measurement techniques. By extrapolating the maximum droplet velocities found by laser Doppler anemometry in the more downstream regions of the spray to the nozzle outlet region, very similar velocities to the one derived from the X-ray measurements close to Bernoulli velocity are evaluated for typical gasoline direct-injection engine conditions. A third access to the nozzle outlet velocity is given by the derivation of penetration curves. The combination of vapor fractions and outlet velocities provides a measure for the initial spray momentum.