Jassim Alhamid
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jassim Alhamid has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Ahmed Ramadhan Al-Obaidi
Mustansiriyah University
7 shared publications - Changki Mo
Washington State University Tri-Cities, Richland, United States, USA
1 shared publication - Faik Hamad
School of Computing, Engineering & Digital Technologies Teesside University Middlesbrough Tees Valley UK
1 shared publication - Hossein Towsyfyan
University of Southampton Southampton UK
1 shared publication - Hussam Ali Khalaf1 shared publication
Matthew D. Whiting
1 shared publication
Latest Publications
- Open Access
- 31 January 2024
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 10 (1) , 175-187
Influence of different geometrical dimple configurations on flow behaviour and thermal performance within a 3D circular pipe
Numerical analysis has been performed to evaluate the heat transfer characteristics and per-formance of a circular pipe with geometrical dimple patterns. Using computational fluid dy-namics (CFD) codes, we examine the effects of geometrical configurations on the flow and thermal behavior of circular pipes with concavity (dimple) diameters. Fluid mixing and flow perturbation are facilitated by perforations across the pipe core and wall regions, thereby im-proving thermal efficiency. In addition, a concavity with a diameter of 4 mm enhances heat transfer. Based on the results of the study, the disrupted pipe wall and pipe core region pro-duce swirls and transverse vortices in the flow that provide superior heat transfer compared to conventional (smooth) pipes. In an increasing Reynolds number (Re), mixing, secondary, and separation flows become larger. Performance evaluation factor (PEF) values increased at low Reynolds numbers when dimple diameter was 1mm. As a result of these improved pipes, heat exchanger efficiency may improve in industrial applications, a key factor for energy con-servation.
- 31 January 2024
- Published by Yildiz Technical University in Journal of Thermal Engineering
- Vol. 10 (1) , 175-187
Open AccessInfluence of different geometrical dimple configurations on flow behaviour and thermal performance within a 3D circular pipe
Numerical analysis has been performed to evaluate the heat transfer characteristics and per-formance of a circular pipe with geometrical dimple patterns. Using computational fluid dy-namics (CFD) codes, we examine the effects of geometrical configurations on the flow and thermal behavior of circular pipes with concavity (dimple) diameters. Fluid mixing and flow perturbation are facilitated by perforations across the pipe core and wall regions, thereby im-proving thermal efficiency. In addition, a concavity with a diameter of 4 mm enhances heat transfer. Based on the results of the study, the disrupted pipe wall and pipe core region pro-duce swirls and transverse vortices in the flow that provide superior heat transfer compared to conventional (smooth) pipes. In an increasing Reynolds number (Re), mixing, secondary, and separation flows become larger. Performance evaluation factor (PEF) values increased at low Reynolds numbers when dimple diameter was 1mm. As a result of these improved pipes, heat exchanger efficiency may improve in industrial applications, a key factor for energy con-servation.
- Open Access
- 18 February 2022
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 32
Effect of different corrugation interruptions Parameters on thermohydrodynamic characteristics and heat transfer performance of 3D Three-dimensional corrugated tube
- 18 February 2022
- Published by Elsevier in Case Studies in Thermal Engineering
- Vol. 32
Open AccessEffect of different corrugation interruptions Parameters on thermohydrodynamic characteristics and heat transfer performance of 3D Three-dimensional corrugated tube
- 13 December 2021
- Published by Wiley in Heat Transfer
- Vol. 51 (3) , 2458-2475
A numerical study to investigate the effect of turbulators on thermal flow and heat performance of a 3D pipe
To reduce the heat exchanger's costs in a highly competitive industry, thermal performance enhancement of the heat exchangers has successfully gained attention in the last few decades. Among different engineering approaches, the application of the enhanced pipes provides a key solution to improve heat performance. In this paper, the investigation develops a numerical study based on the commercially available computational fluid dynamics codes on the turbulent flow in three‐dimensional tubular pipes. Various concavity (dimple) diameters with corrugation and twisted tape configurations are investigated. The study has shown that perforated geometrical parameters lead to a high fluid mixing and flow perturbation between the pipe core region and the walls, hence better thermal efficiency. Moreover, a model of concavity (dimple) with a 4 mm diameter allows the highest heat transfer enhancement among other designs. In addition, the study shows that due to the disturbance between the pipe core region and the pipe wall, the transverse vortices and swirl flow generated are forceful, which leads to better heat transfer enhancement compared with the conventional (smooth) pipes. As the Reynolds number (Re) rises, the mixing flow, secondary, and separation flow extend to become higher than the values in a smooth pipe, allowing a higher value of performance evaluation factor to be achieved for a dimple diameter of 1mm at the low Re values. This study, therefore, shows the promising potential of the enhanced pipes in the heat transfer enhancement of heat exchangers that is crucial in industrial applications to save more energy.
- 13 December 2021
- Published by Wiley in Heat Transfer
- Vol. 51 (3) , 2458-2475
A numerical study to investigate the effect of turbulators on thermal flow and heat performance of a 3D pipe
To reduce the heat exchanger's costs in a highly competitive industry, thermal performance enhancement of the heat exchangers has successfully gained attention in the last few decades. Among different engineering approaches, the application of the enhanced pipes provides a key solution to improve heat performance. In this paper, the investigation develops a numerical study based on the commercially available computational fluid dynamics codes on the turbulent flow in three‐dimensional tubular pipes. Various concavity (dimple) diameters with corrugation and twisted tape configurations are investigated. The study has shown that perforated geometrical parameters lead to a high fluid mixing and flow perturbation between the pipe core region and the walls, hence better thermal efficiency. Moreover, a model of concavity (dimple) with a 4 mm diameter allows the highest heat transfer enhancement among other designs. In addition, the study shows that due to the disturbance between the pipe core region and the pipe wall, the transverse vortices and swirl flow generated are forceful, which leads to better heat transfer enhancement compared with the conventional (smooth) pipes. As the Reynolds number (Re) rises, the mixing flow, secondary, and separation flow extend to become higher than the values in a smooth pipe, allowing a higher value of performance evaluation factor to be achieved for a dimple diameter of 1mm at the low Re values. This study, therefore, shows the promising potential of the enhanced pipes in the heat transfer enhancement of heat exchangers that is crucial in industrial applications to save more energy.
- 14 July 2021
- Published by Wiley in Heat Transfer
- Vol. 50 (7) , 7333-7348
Analysis on flow structure and improvement of heat transfer in 3D circular tube with varying axial groove turbulator configurations
Using passive devices are an efficient method to enhance streamline behavior when liquid flows through the circular pipe. The interrupted structure groove is usually used to change the flow patterns. In this analysis, a heat performance numerical technique is applied to study the characteristics of fluid flow and heat transfer of the circular pipe using different axial groove geometrical configurations with different axial groove numbers, including 2, 3, and 4, under different conditions. The number of annular grooves and circumferential positions are the important parameters to analyse with varying operating conditions, with the Reynolds number (Re) range from 1500 to 23,000. A three‐dimensional coordinate pipe system is applied using tetrahedron grids. The discretization equations are obtained by deriving algebraic approximations to integral conservation equations. Results observed that using this type of passive method has a low effect on pressure dope compared to the normal one (smooth pipe). The flow change occurs near and closed to the axial groove parameters. Moreover, the Nusselt number (Nu) value for the groove turbulators was higher than the normal one, about 14.5%–21%. The friction factor (f) value for the groove turbulators was higher than the normal one, were about 7.5%–24%. Most friction losses are caused by dynamical pressure dissipation owing to more viscous losses closed to the wall surfaces. The improvement of heat performance using this type of passing method was more than 1.2%.
- 14 July 2021
- Published by Wiley in Heat Transfer
- Vol. 50 (7) , 7333-7348
Analysis on flow structure and improvement of heat transfer in 3D circular tube with varying axial groove turbulator configurations
Using passive devices are an efficient method to enhance streamline behavior when liquid flows through the circular pipe. The interrupted structure groove is usually used to change the flow patterns. In this analysis, a heat performance numerical technique is applied to study the characteristics of fluid flow and heat transfer of the circular pipe using different axial groove geometrical configurations with different axial groove numbers, including 2, 3, and 4, under different conditions. The number of annular grooves and circumferential positions are the important parameters to analyse with varying operating conditions, with the Reynolds number (Re) range from 1500 to 23,000. A three‐dimensional coordinate pipe system is applied using tetrahedron grids. The discretization equations are obtained by deriving algebraic approximations to integral conservation equations. Results observed that using this type of passive method has a low effect on pressure dope compared to the normal one (smooth pipe). The flow change occurs near and closed to the axial groove parameters. Moreover, the Nusselt number (Nu) value for the groove turbulators was higher than the normal one, about 14.5%–21%. The friction factor (f) value for the groove turbulators was higher than the normal one, were about 7.5%–24%. Most friction losses are caused by dynamical pressure dissipation owing to more viscous losses closed to the wall surfaces. The improvement of heat performance using this type of passing method was more than 1.2%.
- 17 June 2021
- Published by Wiley in Heat Transfer
- Vol. 50 (7) , 6868-6885
Flow felid and heat transfer enhancement investigations by using a combination of corrugated tubes with a twisted tape within 3D circular tube based on different dimple configurations
Different dimple geometrical configurations with a combination of corrugated tubes and twisted tape are numerically investigated. Water is used as a working fluid for constant heat flux heat transfer conditions at the pipe wall. The dimensionless diameter of the dimples (d/D) used in this study is 0.09, 0.18, 0.27, and 0.36. However, the corrugation configuration diameter is 1 mm. The numerical simulations are carried out at the Reynolds number in the range of 1500–14,000. The outcomes reveal that the friction factor (f) and Nu number are augmented as the dimple diameter increases. The Nu number ratio of 1.25 is found for a dimple pipe tube with a diameter of 4 mm. The numerical outcome presented more mixing, secondary, and vortex produced in the main flow direction and near the pipe wall to the rotating flow induced by twisted tape. Moreover, mixed, secondary vortices and rotational flow originate behind and near the dimple, twisted tape, and corrugation surfaces. These rotational and vortices can promote mixing in flow between the thermal boundary layer and velocity boundary flow layer. So, increase the heat transfer enhancement. The improved pipes with different dimple diameters produce a maximum performance evaluation factor of is more than 1.25.
- 17 June 2021
- Published by Wiley in Heat Transfer
- Vol. 50 (7) , 6868-6885
Flow felid and heat transfer enhancement investigations by using a combination of corrugated tubes with a twisted tape within 3D circular tube based on different dimple configurations
Different dimple geometrical configurations with a combination of corrugated tubes and twisted tape are numerically investigated. Water is used as a working fluid for constant heat flux heat transfer conditions at the pipe wall. The dimensionless diameter of the dimples (d/D) used in this study is 0.09, 0.18, 0.27, and 0.36. However, the corrugation configuration diameter is 1 mm. The numerical simulations are carried out at the Reynolds number in the range of 1500–14,000. The outcomes reveal that the friction factor (f) and Nu number are augmented as the dimple diameter increases. The Nu number ratio of 1.25 is found for a dimple pipe tube with a diameter of 4 mm. The numerical outcome presented more mixing, secondary, and vortex produced in the main flow direction and near the pipe wall to the rotating flow induced by twisted tape. Moreover, mixed, secondary vortices and rotational flow originate behind and near the dimple, twisted tape, and corrugation surfaces. These rotational and vortices can promote mixing in flow between the thermal boundary layer and velocity boundary flow layer. So, increase the heat transfer enhancement. The improved pipes with different dimple diameters produce a maximum performance evaluation factor of is more than 1.25.
- 1 August 2018
- Published by Elsevier in Biosystems Engineering
- Vol. 172, 124-133
Cellulose nanocrystals reduce cold damage to reproductive buds in fruit crops
- 1 August 2018
- Published by Elsevier in Biosystems Engineering
- Vol. 172, 124-133
Cellulose nanocrystals reduce cold damage to reproductive buds in fruit crops