MHMaciej Hildebrand

Maciej Hildebrand

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Maciej Hildebrand has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Load Measurement and Control of Auxiliary Bridge Supports During Passage of Oversized Vehicles

    by Czesław Machelski, Maciej Hildebrand, Jarosław Rybak

    Actual live loads on bridges can be categorized into ordinary loads and loads exceeding standard limits induced by abnormal transport. A bridge structure subjected to a heavy load may behave differently than under a light load. Selected analyses performed as part of an assessment regarding the presence of a vehicle weighing 620 tons on the bridge are presented in the paper. The decision on the structural safety for the passage of such a vehicle is made after a structural check, taking into account the current technical condition of the structure. The bridge discussed here was strengthened to achieve a load-bearing capacity significantly higher than its original rating. Two additional steel frame supports were installed beneath the existing span, which originally functioned as a simply supported beam. These supports are engaged only when the bridge is subjected to exceptionally heavy, overweight loads. Consequently, the support system of the bridge span is variable, depending on the loads applied and the structural deflections. It has been found that the results of measurements taken during the previous overweight transport are very useful for proper structural modeling. The main aim of this work is to present a methodology for determining or modeling the structural behavior of nontypical bridges under very exceptional loads.

  • Special bridge over the Warta River in Poznań – technical condition after 50 years of operation

    by Maciej Hildebrand, Aleksander Mróz

    The article presents the results of a comprehensive technical review and geodetic measurements of the Karolin special suspension bridge over the Warta River in Poznań, which is a key element of the municipal heating main (4 pipes × Ø800 mm). The text describes the history of the facility's operation dating back to 1975 and the scope of renovation works carried out in 2024, after the second quarter of a century of operation. Particular emphasis was placed on the methodology of the five-year inspection and insightful, geodetic control measurements aimed at determining the evolution of the geometry of the structure over the years. The presented analyses, including the comparison of overhang arrows, deck elevation and deviations in the plan, lead to conclusions regarding the susceptibility of the structure to thermal and useful loads. On the basis of the minor irregularities detected, a number of maintenance recommendations were formulated, including proposals to improve the geometric monitoring system of this strategic element of the energy infrastructure.

  • Open Access

    Model of bridge with supports activated under heavy load

    by Czesław Machelski, Maciej Hildebrand, Maksymilian Kliński

    Road bridges can sometimes be used exceptionally for nonstandard loads (heavy cargo). This article presents structural analyses of a bridge loaded by a 620-ton vehicle. The case in question concerns a specially reinforced bridge. Its specific feature is the use of additional frame supports, which are activated only when loads significantly exceed the service load. Therefore, the structure’s structural system is variable, and the additional support is activated during increased load intensity. The article demonstrates that the results of field tests performed during abnormal loads are necessary to properly model the structure. It is also essential to determine the degree of interaction (bonding) between concrete deck slab and the steel beams, the load distribution among the girders, and the stiffness of the frame supports, considering the unintended gaps between the span and the frames.

  • Ocena konstrukcji mostowej wobec planowanegodrogowego transportu nienormatywnego o dużym ciężarze

    by Czesław Machelski, Maciej Hildebrand, Maksymilian Kliński

    Mosty drogowe mogą być w niektórych przypadkach wykorzystywane w sposób nadzwyczajny, w związku z prowadzonymi transportami nienormatywnymi, gdy wymiary i ciężar całkowity pojazdu wraz z ładunkiem znacznie przekraczają wartości standardowe. Przejazd takiego pojazdu jest możliwy pod warunkiem sprawdzenia dostępnej wolnej przestrzeni na obiekcie mostowym i na dojazdach, przeprowadzenia oceny rzeczywistego stanu technicznego budowli, określenia wartości sił wewnętrznych podczas planowanego przejazdu oraz uzyskania formalnych pozwoleń od zarządcy obiektu na nietypowe, nienormatywne korzystanie z elementu infrastruktury. Sformułowanie opinii o możliwości przeprowadzenia przejazdu nienormatywnego jest więc poprzedzone przeprowadzeniem niezbędnych obliczeń statyczno- wytrzymałościowych oraz dokonaniem przeglądu obiektu, przy czym w przypadku niektórych szczególnie ciężkich transportów nienormatywnych przeglądy te cechuje względnie wysoki poziom szczegółowości. W szeregu przypadków prowadzone są analizy geometryczne z wykorzystaniem cyfrowych map terenu mające na celu wyeliminowanie kolizji ładunku z otoczeniem. W artykule przedstawiono czynności podjęte w ramach przygotowywania opinii dotyczącej przejazdu nienormatywnego o bardzo dużym ciężarze łącznym, sięgającym 6,2 MN (masa około 620 t). Opisywany przypadek jest o tyle specyficzny, że dotyczy mostu specjalnie przygotowanego (wzmacnianego) do przejazdów nienormatywnych, ze względu na fakt, iż znajduje się w ciągu drogi prowadzącej do dużego zakładu przemysłowego, często wykorzystywanej do przewozu bardzo ciężkich ładunków

  • Open Access

    Measurement of Deformation and Force Changes Recorded During Long-Term Monitoring of a Steel Cable-Stayed Bridge

    by Czesław Machelski, Maciej Hildebrand, Jarosław Rybak

    Long-term processes, manifesting themselves in slow geometrical alterations and changes in internal forces, have been known and observed to take place mainly in large bridges made of prestressed concrete, but they also occur, albeit to a smaller degree, in steel bridges. Two sets of data, coming from, respectively, multi-year geodetic surveys and the structural health monitoring of a cable-stayed bridge (forces in its stays), were compared. Using the collocation method, displacements consistent with the results of the geodetic measurements were input into a numerical model of the bridge. Then, changes in the forces in the stays, which should accompany the displacements, were computed. The computed changes were compared with the actual changes in the mean force values in the stays of the bridge recorded over an eight-year period of its structural health monitoring. The two sets of data were found to be not in satisfactory good agreement. The main factors making it difficult to reach full agreement were the very small relative values of the observed geometrical alterations (the deformation, i.e., the increase in deflection, of the 375 m long span amounting merely 10–15 mm after eight years of periodic measurement) and the very small changes (amounting to about 0.5% for 8 years of monitoring) in the mean forces in the stays, as well as the possible mistakes in the survey. Despite these difficulties, the employed collocation method proved to be effective. It was also found that the long-term geometrical alterations and the changes in the forces in the stays do not adversely affect the safety of the bridge and its use.


  • Open Access

    Investigation of the Stiffness of a Specially Strengthened Bridge When Crossed by Very Heavy Vehicles – A Case Study

    by Czesław Machelski, Maciej Hildebrand, Maksymilian Kliński

    The measurement of bridge deflection induced by a motor vehicle is an effective way of verifying the weight of the vehicle, and even of determining the layout of its axles. If the vehicle’s weight and the impacts of its individual axles are known, deflection measurements can be used to verify the stiffness of the bridge structure and to evaluate the effectiveness of steel-concrete composite span integration. The bridge in this case study had been specially permanently adapted to carrying very heavy loads, generated by overweight transports reaching the total weight of a few to over 10 MN. The results of measurements of span deflections induced by a heavy vehicle and the way they were used to assess the weight of another overweight transport unit crossing the bridge are presented in the paper. The existing strengthening of the bridge has been found to be universal and effective for various overweight transports.


  • The oldest concrete bridge in Poland is in Szczecin!

    by Jan Biliszczuk, Maciej Hildebrand, Krystyna Januszkiewicz, Marco Teichgraeber


  • Open Access

    Large-Scale Testing and Long-Term Monitoring of Reinforced Earth Abutment – A Case Study

    by Maciej Hildebrand

    Standard methods of controlling geotechnical structures are based on testing of individual elements (e.g., piles, anchors, barrettes) or on inventory of their displacements (for instance, current control, i.e., monitoring of retaining structures). It is only the bridgework where, due to uniqueness and importance of structures, the examinations are often run for the whole structures. The main problems are then the following: how to ensure proper repeatability of measurement accuracy (for long-term testing), how to establish optimum criteria of assessing the test results, how to use the results to make possible repair actions and how to interpret the obtained results. Based on an example of test of bridge abutment out of reinforced earth, the paper presents the method of displacement testing, basic criteria of assessing the results, measurement results during static load phase, during dynamic phase and results of long-term measurements. Large number of measurements enables for both evaluation of technical condition of the structure under testing (which was the main goal of the procedures performed) and drawing conclusions referring to the methodology of testing the structure out of reinforced earth as concerns the evaluation criteria adopted.


  • Open Access

    Cable-Stayed Bridge Loads Caused by Traffic Congestion on the Deck Measured with Bridge Monitoring System

    by Czesław Machelski, Maciej Hildebrand

    Structural safety of a bridge depends, among other things, on the number of vehicles passing on its deck, their weights and distribution of loads to their axes. A large number of vehicles can accumulate on the bridge in a controlled state, i.e., during an acceptance test including load testing, and during traffic congestion on the bridge, which is a fortuitous event addressed in this paper. The paper deals with the analysis of load intensity on one bridge carriageway when it is fully and randomly filled during traffic congestion. The influence functions of the forces in the cables are used to determine the effects of loads exerted by the vehicles moving at very low speed. Effects of such loads are studied considering an exemplary cable-stayed bridge. Since the measurement basis was limited, the iterative algorithm was used. It consists in shortening the girder sections under analysis to the area appropriate for determining the load in each successive step of iteration. Ineffectiveness of the traditional algorithm, where the determined system of equations is resolved, is an important premise for using such algorithm. The results of numerical analysis show that the load intensity caused by traffic congestion is relatively high. It has been demonstrated that the matrix method may be successfully used to determine the real load of bridges on the basis of selected parameters measured in the bridge structure, also for complex scheme bridges, including the cable-stayed bridges.


  • Open Access

    Measurement of Temperature Distribution Within Steel Box Girder of Vistula River Bridge in Central Europe

    by Maciej Hildebrand, Łukasz Nowak

    Uneven temperature distribution in a structural element constitutes one of its load factors. Temperature fields occurring in structural elements lead to stresses and strains. The values of internal stresses are directly related to temperature distribution and degree of freedom for element deformation. The best way to get information about temperature distribution in an element is to take measurements on a real object. Such measurements have been run or are still taken over decades in various parts of the world, e.g. in Western Europe, USA, China, South America. In a number of cases, such examinations were carried out for objects constructed in warm or hot climate. It is a lot harder to find the results of measurements made in the countries with moderate and transitional climate, like in the Central or East-Central Europe. This paper presents measurement methodology and results gained for a large steel bridge located in the East European Plain, about 52.5° N northern latitude. Permanently installed contact sensors, temporary sensors, as well as pyrometry and thermography were used. An attempt was made to determine temperature distribution in a steel box girder of a bridge using thermovision technique. Approximate temperature distribution patterns in the main span girder were determined from thermal photographs taken. The most important results of examinations are the images of temperature fields in the main span girder related to solar radiation that first and foremost directly affects the bridge deck.