TKTatyana Kiose

Tatyana Kiose

*This is an algorithmically generated author record based on publicly available information.

Tatyana Kiose has a total of 47 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Nanocatalysts based on palladium(II), copper(II) and acid-modified vermiculite compounds for the oxidation of carbon monoxide with atmospheric oxygen

    by Odesa I.I. Mechnikov National University, T.L. Rakytska, Physical and Chemical Institute of Human Health and Environmental Protection, T.O. Kiose, L.P. Oleksenko, Taras Shevchenko National University of Kyiv

    In this work, the physicochemical properties of natural vermiculite, its acid-modified forms, and copper–palladium catalysts based on it were investigated. Acid-modified forms of vermiculite were obtained by refluxing with nitric acid solutions (0.25; 0.5; 1.0; 3.0; 4.0; 6.0; and 8.0 mol/L) for one hour. Nanocatalysts were prepared by the impregnation method at moisture capacity, followed by drying at 1000C for 3 hours. The initial vermiculite, the acid-modified samples, and the catalysts were characterized by X-ray phase analysis, IR spectroscopy, and nitrogen adsorption. Catalyst samples were tested in the reaction of carbon monoxide oxidation with oxygen under the following conditions: initial concentration of 300 mg/m3, temperature of 200C, relative humidity of the gas–air mixture of 67%, and volumetric flow rate of 1 L/min. It was established that the natural material is polyphase and, in addition to the main vermiculite phase (52 wt.%), contains impurity phases of muscovite, cordierite, and sepiolite, each with a content not exceeding 14–18 wt.%. The deposited palladium(II) and copper(II) compounds were well homogenized on the surface of the carrier and did not undergo phase transformations. The crystallites of the vermiculite phase were nanosized. IR spectroscopy showed that under the action of nitric acid (CHNO3>4 mol/L) and upon fixation of palladium(II) and copper(II) compounds, the layered structure of vermiculite was altered, its amorphization increased, and nanosilica was formed. As a result of acid modification, the specific surface area of vermiculite samples increased from 4.49 m2/g to 282.0 m2/g. Testing of the nanocatalyst samples showed that CO oxidation occurred in a stationary mode only when the carrier had been modified at CHNO3>4 mol/L, with the degree of carbon monoxide conversion reaching 88%.

  • Open Access

    CHEMISORPTION-CATALYTIC PROPERTIES OF COMPOSITIONS BASED ON ІRON(III) CHLORIDE AND NATURAL SORBENTS OF UKRAINE IN THE REACTION OF SULFUR DIOXIDE WITH ATMOSPHERIC OXYGEN

    by T. O. Kiose, Т. Л. Ракитська, L. A. Raskola

    Sulfur dioxide is one of the most common toxic atmospheric pollutants that enters the air as a result of both natural and anthropogenic processes. Common technologies for its removal are based on adsorption processes using natural, synthetic zeolites, activated carbon, carbon materials, as well as chemisorption with the participation of metal oxides. Accumulated literature data indicate the ability of 3d-metal compounds to catalyze the oxidation of SO2 both in solution and in a droplet. However, dissolved metal complex catalysts for the oxidation of SO2 have limited application in air purification practice. The use of metal complex compounds fixed on solid supports is considered a promising direction, however, their activity in interaction with SO2 has not been studied sufficiently. The aim of our work is to evaluate the protective and sorption properties of chemisorption-catalytic compositions based on іron(III) chloride, fixed on carriers of various origins in the process of air purification from sulfur dioxide at its concentration in the air of 15 MPC (150 mg/m3). In the work, samples of natural minerals of various origins were used as a sorbent for sulfur dioxide and a carrier for compositions based on іron(III) chloride-zeolites, layered aluminosilicates and dispersed silicas. It was established that the natural sorbents used in the work are not real minerals and are characterized by a complex phase composition. In natural clinoptilolite, in addition to the dominant phase of clinoptilolite (> 70%), impurity phases are contained a-quartz, mordenite, hematite; in natural bentonite, along with the main phase of montmorillonite, contains calcite, α-quartz, and amorphous SiO2 in varying amounts; while tripoli is a crystalline mineral containing four main phases – α-SiO2, α-tridymite, β-cristobalite and α-cristobalite. It was found that the effectiveness of chemisorption-catalytic compositions based on іron(III) chloride in the process of absorbing sulfur dioxide depends on the concentration of FeCl3 and the nature of the carrier.

  • Open Access

    HISTORY AND CONCEPTS OF THE DEVELOPMENT OF METAL COMPLEX AND METAL OXIDE NANOCATALYSTS FOR SOLVING ENVIRONMENTAL PROBLEMS

    by Т. Л. Ракитська, T. O. Kiose

    The article presents the results of many years of research devoted to the development of low-temperature metal complex and metal oxide nanocatalysts for respiratory purposes. This was one of the parts of the general comprehensive project to create modern multifunctional means of protecting the environment and the human respiratory system, which was scientifically substantiated by Professor Alim-Abdul Adimovich Ennan and implemented throughout his life. The work highlights the following issues: general information on the physicochemical justification of methods for purifying air from gaseous toxic substances and requirements for respiratory catalysts; scientific concepts for creating metal complex catalysts of various origins for the oxidation of CO, PH3, SO2 and ozone reduction fixed on carriers; examples of chemical synthesis of metal oxide nanocatalysts and their activity in ozone decomposition reactions and sulfur dioxide oxidation; examples of utilization of nanodispersed particles that are synthesized in the process of welding metals and exhibit catalytic properties in the ozone decomposition reaction; examples of implementation of research results: respirators, installations, publications, dissertation defences, educational process; the scientific school “Metal complex compounds in catalysis” has been created and is operating. The most common toxic gases are SO2, H2S, HF, P2O5, NOx, NH3, SiF4 (1); PH3, AsH3, NO, CO, O3 (2), which are classified by acid-base (1) and redox properties (2). It follows that air purification from the listed substances can be implemented only through a series of sequential stages, namely, trapping of aerodispersed particles; chemisorption absorption of substances classified in group (1); catalytic neutralization of PH3, AsH3, CO, SO2 and O3 in the presence of catalysts fixed on various carriers, which can be metal complex compounds, as well as metal and metal oxide nanocatalysts. The intensive use of catalysis to solve environmental problems has contributed to the formation of a new scientific direction “Environmental Catalysis”, within which theoretical and practical issues of developing effective catalysts for protecting the environment and humans are being addressed. The implementation of this aspect of environmental catalysis is associated with the design of highly effective catalysts for personal respiratory protective equipment (PPE) (gas masks, respirators, autonomous purified air supply systems) that ensure safe and comfortable working conditions. The analysis shows that the range of catalysts for PPE is very limited, which is due not only to the reluctance of companies to invest in the development of new catalysts, but also to specific requirements for such catalysts: ensuring stable air purification from toxic gaseous substances to the MPC and below with constantly changing inlet characteristics of the air flow (qualitative and quantitative composition; temperature; humidity); high catalyst activity with optimal contact time with the purified gas (no more than 0.04 s in a lightweight respirator); simple, cheap and environmentally friendly catalyst preparation technology; catalyst manufacturability in the design of respiratory protective equipment, i. e. being well adaptable to different geometric shapes; small weight and low aerodynamic drag; compliance with sanitary, chemical and toxicological standards applicable to personal protective equipment.

  • Open Access

    INFLUENCE OF PRE-ADSORBED SULPHUR DIOXIDE AND WATER VAPOR ON THE PROTECTIVE PROPERTIES OF A COPPER-PALLADIUM CATALYST FOR CARBON MONOXIDE OXIDATION

    by T. O. Kiose, Т. Л. Ракитська, L. A. Raskola, K. O. Holubchyk, A. O. Zagoruy

    It is known that the largest sources of sulfur dioxide (SO2) and carbon monoxide (CO) emissions into the atmosphere are the thermal power industry, ferrous and non-ferrous metallurgy, and the chemical industry. The presence of gaseous toxicants in the working area in concentrations that far exceed the MPC (20 mg/m3 for CO and 10 mg/m3 for SO2) acutely raises the issue of personnel respiratory protection. This necessitates the use of personal respiratory protective equipment (RPE) by workers equipped with filters that protect against both substances. We have developed a highly efficient low-temperature catalyst in which the carrier is hydrothermally modified dispersed silica tripoli (Н2О-Tr(К-І)). For such a catalyst, there are no studies on the influence of catalytic poisons, namely SO2 and H2O, on its activity in the reaction of low-temperature oxidation of CO with air oxygen. The work investigated the adsorption properties of hydrothermally modified dispersed silica trefoil and the carbon monoxide oxidation catalyst Pd(II)-Cu(II)/Н2О-Tr(К-І) with respect to water vapor and sulfur dioxide, as well as their effect on the protective properties of the catalyst. Analysis of water vapor adsorption-desorption isotherms by samples of natural and chemically modified tripoli allows us to attribute them to sorbents with a heterogeneous porous structure with a predominance of transitional pores. The effect of the additional water content on the activity of the Pd(II)-Cu(II)/Н2О-Tr(К-І) catalyst for carbon monoxide oxidation was investigated. It was established that with an increase in the water content, the degree of CO conversion decreases due to blocking of the active centers of the catalyst, or capillary condensation, which affects the internal diffusion processes. The adsorption properties of natural and chemically modified tripoli at low temperatures from a gas-air mixture in which the SO2 content was 150 mg/m3 were analyzed. It was found that the protective action time increases from 15 min for H2O-Tr(K-I) and up to 250 min for the Pd(II)-Cu(II)/H2O-Tr(K-I) catalyst, which indicates the participation of Pd(II) and Cu(II) in the reaction with sulfur dioxide. It was found that the copper-palladium catalyst, previously poisoned with sulfur dioxide, loses catalytic activity in the oxidation reaction of carbon monoxide as a result of the irreversible binding of part of palladium(II) with sulfur dioxide and its loss of the ability to coordinate and activate the CO molecule. Therefore, to prevent catalyst poisoning when using it in respiratory protection against carbon monoxide, it is necessary to provide for preliminary air purification from aerosol particles, sulfur dioxide, and water vapor.

  • Open Access

    PREPARATION AND PROTECTIVE PROPERTIES OF A CATALYST FOR THE OXIDATION OF CARBON MONOXIDE BY AIR OXYGEN BASED ON Pd(II), Cu(II) COMPOUNDS AND CARBON FIBER MATERIAL

    by T. O. Kiose, Т. Л. Ракитська

    Ensuring reliable protection of the respiratory organs of the workers in various industries from carbon monoxide is a complex and multifaceted task. In order to solve a number of issues, it is necessary to carry out research aimed at the development of appropriate catalysts, their optimization, and, taking into account the operational characteristics of catalysts, develop recommendations for their use in the means of individual protection of respiratory organs. The work is devoted to the synthesis method optimization and the operational characteristics determination of the catalyst for the oxidation of carbon monoxide with air oxygen, which includes compounds of palladium(II), copper(II), and two batches of non-woven carbon fiber material Karbopon B-Active-200-65-A were used as a carrier (CFM-I and CFM-II), with hydrated cellulose as the precursor. The CFM carrier weighing 0.5–2.5 g was pre-dried at t = 110 °С to a constant weight and impregnated according to moisture content with a water-alcohol solution containing palladium and cuprum precursors in the given ratios in the form of K2PdCl4, Cu(NO3)2 and auxiliary component KBr. The ratio of the solid phase to the liquid phase is 1:10. The wet mass was kept in a closed Petri dish at 20–25 °С for 20–24 hours, then dried in a thermal cabinet in an air environment at 110 °С to a constant mass. Samples were cooled in a desiccator to room temperature. Testing of catalysts of the composition K2PdCl4–Cu(NO3)2–KBr/CFM was carried out in a flow-through gas thermostated at 293 K installation with an “allonge” type reactor with a fixed catalyst layer. The dimensions of the reactor and the speed of the gas-air mixture correspond to the regime of ideal compression and the course of the reaction in the kinetic region. The method of obtaining was optimized and the operational characteristics of the catalyst for the oxidation of carbon monoxide by air oxygen, which includes compounds of palladium (II), copper (II) and carbon fiber material, were determined. As a result of testing catalyst samples based on CFM-I and CFM-II in the carbon monoxide oxidation reaction, it was established that despite a more developed structure, the catalyst based on CFM-II is less active than the catalyst based on CFM-I; the degree of CO conversion increases with an increase in the effective contact time. The catalyst based on CFM-II at τeff = 0.45 sec in the region of CinCO from 50 to 300 mg/m3 provides stable air purification from CO much lower than MPCCO (20 mg/m3) and can be recommended for use in respiratory devices.

  • Open Access

    CATALYST BASED ON PALLADIUM(II), COPPER(II) COMPOUNDS AND THERMALLY-MODIFIED TRIPOLI FOR THE PREPARATION OF RESPIRATORY REMEDIES FROM CARBON MONOXIDE IN EMERGENCY SITUATIONS

    by T. O. Kiose, Т. Л. Ракитська, K. O. Holubchyk

    Nowadays, the number of emergency situations related to fires is quite high. The high percentage of human deaths is mainly due to poisoning by gaseous toxic substances including carbon monoxide. The most problematic issue is the development or application of existing catalysts in means of individual protection of human respiratory organs – respirators, gas masks, self-rescuers. The compositions based on thermally modified tripoli obtained by the method of impregnation of the carrier by moisture content with compounds of copper(II), palladium(II) and potassium bromide were investigated. According to X-ray phase analysis, it was established that thermally modified tripoli is a polyphase crystalline mineral containing the following main phases: a-quartz, a-tridymite, b-cristobalite, a-cristobalite. The influence of the initial concentration of CO, which does not exceed 15 MPC, on the kinetic and stoichiometric parameters of the reaction varied in the range from 100 to 300 mg/m3. It was noted that the reaction rate in the stationary mode (Wst) is directly proportional to the increase in the initial concentration of carbon monoxide in the gas phase. The values of the constant kI and the degree of CO conversion (ηst) do not depend on CinCO, which also confirms the first order of CO concentration. Particular attention is paid to the aspects of ensuring protection against carbon monoxide when its concentration exceeds 15 MPC. Usually, special equipment, such as filtering self-rescuers, is used to clean the air from carbon monoxide at concentrations from 1000 to 6500 mg/m3. The catalyst developed by us is intended for use in lightweight personal respiratory protective equipment (RPE) at concentrations not exceeding 15 MPC. Therefore, there was an interest in researching the possibilities of using this catalyst in the self-saving filter system. The concentration of carbon monoxide in the gas-air mixture was varied from 400 to 2500 mg/m3 in the presence of the К2PdCl4-Cu(NO3)2-КBr/300-Tr(K) system. It was established that Wst increases in direct proportion with an increase in the gas-air mixture up to 1250 mg/m3, which indicates the first order of the reaction according to carbon monoxide. It was found that at CinCO = 1000 mg/m3 only under the condition τ´ = 1.13 s (mk = 10 g) the К2PdCl4-Cu(NO3)2-KBr/Tr catalyst provides air purification below the breakthrough CO concentration (CfCO = 200 mg/m3). Experiments on the influence of SO2 on the activity of carbon monoxide oxidation catalysts have shown that they lose their activity, so in air purification systems from CO, it is necessary to provide for the stage of capturing sulfur dioxide.

  • Open Access

    SYNERGETIC EFFECTS OF PALLADIUM(II) AND COPPER(II) COMPOUNDS FIXED ON MODIFIED PHLOGOPITE IN THE REACTION WITH SULFUR DIOXIDE

    by T. O. Kiose, A. P. Nazar, T. L. Rakyts’ka

    Досліджено кінетику взаємодії діоксиду сульфуру з моно- та біметальними композиціями на основі сполук паладію(ІІ), купруму(ІІ) і кислотно-модифікованого природного (Phl) та термічно-спученого (ТС-Phl) флогопіту. Доведено, що біметальні композиції Pd(II)-Cu(II)-KBr/S̅ (S̅ = 6H-Phl-1; X̅H-TC-Phl-1, X̅ = 1, 2, 3, 6 M HNO3) в реакції з SO2 виявляють синергетичний ефект з коефіцієнтом КS >> 1, що призводить до збільшення часу захисної дії зразків та кількості поглиненого діоксиду сульфуру.

  • Composition and Activity of Copper-Palladium Catalyst on Carbon Fiber Material for Air Purification from Carbon Monoxide

    by Tatyana Kiose, Tatyana Rakitskaya, Alim Ennan, Volodymyr Vasylechko, Halyna Gryshchouk

    A set of research methods (X-ray phase, desorption, kinetic) was used to determine the state of the basic components K2PdCl4 and Cu(NO3)2 in the catalyst for the oxidation of carbon monoxide by oxygen. It was found that the palladium (II) and copper (II) initial compounds under the action of carbon fiber carrier change their state. Palladium is reduced to X-ray amorphous Pd0, and copper (II) is in the form of a crystalline phase Cu2(OH)3Cl. It was found that the catalyst exhibits protective properties within the initial concentrations of carbon monoxide  300 mg/m3 and an effective contact time of 0.45 s and can be used in human respiratory protection.