Kristina Golubchik
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Kristina Golubchik has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Tatyana L. Rakitskaya
Odesa I. I. Mechnikov National University, Faculty of Chemistry and Pharmacy, Department of Inorganic Chemistry and Chemical Education
4 shared publications - Tatyana Kiose
Mechnikov National University
2 shared publications - Vitaliya Volkova
Faculty of Chemistry and Pharmacy, Odessa I.I. Mechnikov National University, 2, Dvoryanska Street, 65082 Odessa, Ukraine
2 shared publications - Alim A. Ennan
Physico-Chemical Institute of Environment and Human Protection
1 shared publication - Ivan O. Shyshkin
Odesa National Medical University
1 shared publication - Kiose
Department of Inorganic Chemistry and Chemical Ecology, Odessa I.I. Mechnikov National University, 2, Dvoryanskaya St., Odessa, 65082, Ukraine
1 shared publication
Latest Publications
- Open Access
- 26 December 2025
- Published by The State Expert Center of the Ministry of Health of Ukraine in Farmatsevtychnyi zhurnal
- No. 6,p. 65-72
Express methods of chemical analysis of medicines by analytical centers to prevent counterfeit
Counterfeiting of medicines is a serious global problem that threatens the health of the population and the stability of the pharmaceutical market. According to WHO, a significant part of the drugs may contain an unreliable composition or an insufficient amount of the active substance, which causes ineffective treatment. In Ukraine, drugs of various groups are falsified, in particular antibiotics. Chemical express methods are important – color reactions and precipitation, which allow you to quickly identify the active substance and effectively counteract falsification. Development and implementation of express methods for drug analysis using chemical methods for rapid analysis of the quality of finished drugs in modern conditions. To achieve the goal, the following drugs were used: Albendazole-Farmex, tablets, 400 mg; Metoclopramide-Darnitsa, tablets 10 mg; Ganciclovir-Farmex, 500 mg, lyophilisate for solution for infusions; Setegis (Terazosin), tablets 5 mg; Bisacodyl-Darnitsa, tablets 5 mg. Reagents of the «pure for analysis» class were used. The methods of chemical analysis were based on the identification of analytical centers of the structure of the active substance. All the studied compounds contain a heterocyclic and/or tertiary nitrogen atom of the pyridine type, which allows the use of general alkaloid precipitating reagents through the protonation of nitrogen and the formation of colored salts. The structures also contain a primary aromatic amino group, so the study was divided into two groups of reactions: the formation of azo dyes with phenolic derivatives or aromatic amines in an alkaline medium and the formation of azomethine dyes with aromatic aldehydes in an acidic medium. Azo dyes with resorcinol, aniline, chrome dark blue and Congo red are formed even in highly diluted solutions and give characteristic analytical effects. Thus, the results of the experiments demonstrated the possibility of using chemical rapid analysis for qualitative identification of a number of drugs of predominantly heterocyclic structure by individual analytical centers during the primary rapid analysis of drugs in conditions where it is impossible to use additional equipment. A clear analytical effect was observed in experiments involving the primary aromatic amino group. A promising option for identification is the reaction of formation of ionic associates with azo dyes.
- 26 December 2025
- Published by The State Expert Center of the Ministry of Health of Ukraine in Farmatsevtychnyi zhurnal
- No. 6,p. 65-72
Open AccessExpress methods of chemical analysis of medicines by analytical centers to prevent counterfeit
Counterfeiting of medicines is a serious global problem that threatens the health of the population and the stability of the pharmaceutical market. According to WHO, a significant part of the drugs may contain an unreliable composition or an insufficient amount of the active substance, which causes ineffective treatment. In Ukraine, drugs of various groups are falsified, in particular antibiotics. Chemical express methods are important – color reactions and precipitation, which allow you to quickly identify the active substance and effectively counteract falsification. Development and implementation of express methods for drug analysis using chemical methods for rapid analysis of the quality of finished drugs in modern conditions. To achieve the goal, the following drugs were used: Albendazole-Farmex, tablets, 400 mg; Metoclopramide-Darnitsa, tablets 10 mg; Ganciclovir-Farmex, 500 mg, lyophilisate for solution for infusions; Setegis (Terazosin), tablets 5 mg; Bisacodyl-Darnitsa, tablets 5 mg. Reagents of the «pure for analysis» class were used. The methods of chemical analysis were based on the identification of analytical centers of the structure of the active substance. All the studied compounds contain a heterocyclic and/or tertiary nitrogen atom of the pyridine type, which allows the use of general alkaloid precipitating reagents through the protonation of nitrogen and the formation of colored salts. The structures also contain a primary aromatic amino group, so the study was divided into two groups of reactions: the formation of azo dyes with phenolic derivatives or aromatic amines in an alkaline medium and the formation of azomethine dyes with aromatic aldehydes in an acidic medium. Azo dyes with resorcinol, aniline, chrome dark blue and Congo red are formed even in highly diluted solutions and give characteristic analytical effects. Thus, the results of the experiments demonstrated the possibility of using chemical rapid analysis for qualitative identification of a number of drugs of predominantly heterocyclic structure by individual analytical centers during the primary rapid analysis of drugs in conditions where it is impossible to use additional equipment. A clear analytical effect was observed in experiments involving the primary aromatic amino group. A promising option for identification is the reaction of formation of ionic associates with azo dyes.
- 8 July 2025
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 769 (15-18) , 1471-1482
Сopper-palladium nanocatalysts for carbon monoxide oxidation supported on dispersed silica
- 8 July 2025
- Published by Taylor & Francis in Molecular Crystals and Liquid Crystals
- Vol. 769 (15-18) , 1471-1482
Сopper-palladium nanocatalysts for carbon monoxide oxidation supported on dispersed silica
- Open Access
- 25 October 2023
- Published by Odesa I.I. Mechnikov National University in Odesa National University Herald. Chemistry
- Vol. 28 (3(86)) , 5-17
CATALYST BASED ON PALLADIUM(II), COPPER(II) COMPOUNDS AND THERMALLY-MODIFIED TRIPOLI FOR THE PREPARATION OF RESPIRATORY REMEDIES FROM CARBON MONOXIDE IN EMERGENCY SITUATIONS
Nowadays, the number of emergency situations related to fires is quite high. The high percentage of human deaths is mainly due to poisoning by gaseous toxic substances including carbon monoxide. The most problematic issue is the development or application of existing catalysts in means of individual protection of human respiratory organs – respirators, gas masks, self-rescuers. The compositions based on thermally modified tripoli obtained by the method of impregnation of the carrier by moisture content with compounds of copper(II), palladium(II) and potassium bromide were investigated. According to X-ray phase analysis, it was established that thermally modified tripoli is a polyphase crystalline mineral containing the following main phases: a-quartz, a-tridymite, b-cristobalite, a-cristobalite. The influence of the initial concentration of CO, which does not exceed 15 MPC, on the kinetic and stoichiometric parameters of the reaction varied in the range from 100 to 300 mg/m3. It was noted that the reaction rate in the stationary mode (Wst) is directly proportional to the increase in the initial concentration of carbon monoxide in the gas phase. The values of the constant kI and the degree of CO conversion (ηst) do not depend on CinCO, which also confirms the first order of CO concentration. Particular attention is paid to the aspects of ensuring protection against carbon monoxide when its concentration exceeds 15 MPC. Usually, special equipment, such as filtering self-rescuers, is used to clean the air from carbon monoxide at concentrations from 1000 to 6500 mg/m3. The catalyst developed by us is intended for use in lightweight personal respiratory protective equipment (RPE) at concentrations not exceeding 15 MPC. Therefore, there was an interest in researching the possibilities of using this catalyst in the self-saving filter system. The concentration of carbon monoxide in the gas-air mixture was varied from 400 to 2500 mg/m3 in the presence of the К2PdCl4-Cu(NO3)2-КBr/300-Tr(K) system. It was established that Wst increases in direct proportion with an increase in the gas-air mixture up to 1250 mg/m3, which indicates the first order of the reaction according to carbon monoxide. It was found that at CinCO = 1000 mg/m3 only under the condition τ´ = 1.13 s (mk = 10 g) the К2PdCl4-Cu(NO3)2-KBr/Tr catalyst provides air purification below the breakthrough CO concentration (CfCO = 200 mg/m3). Experiments on the influence of SO2 on the activity of carbon monoxide oxidation catalysts have shown that they lose their activity, so in air purification systems from CO, it is necessary to provide for the stage of capturing sulfur dioxide.
- 25 October 2023
- Published by Odesa I.I. Mechnikov National University in Odesa National University Herald. Chemistry
- Vol. 28 (3(86)) , 5-17
Open AccessCATALYST BASED ON PALLADIUM(II), COPPER(II) COMPOUNDS AND THERMALLY-MODIFIED TRIPOLI FOR THE PREPARATION OF RESPIRATORY REMEDIES FROM CARBON MONOXIDE IN EMERGENCY SITUATIONS
Nowadays, the number of emergency situations related to fires is quite high. The high percentage of human deaths is mainly due to poisoning by gaseous toxic substances including carbon monoxide. The most problematic issue is the development or application of existing catalysts in means of individual protection of human respiratory organs – respirators, gas masks, self-rescuers. The compositions based on thermally modified tripoli obtained by the method of impregnation of the carrier by moisture content with compounds of copper(II), palladium(II) and potassium bromide were investigated. According to X-ray phase analysis, it was established that thermally modified tripoli is a polyphase crystalline mineral containing the following main phases: a-quartz, a-tridymite, b-cristobalite, a-cristobalite. The influence of the initial concentration of CO, which does not exceed 15 MPC, on the kinetic and stoichiometric parameters of the reaction varied in the range from 100 to 300 mg/m3. It was noted that the reaction rate in the stationary mode (Wst) is directly proportional to the increase in the initial concentration of carbon monoxide in the gas phase. The values of the constant kI and the degree of CO conversion (ηst) do not depend on CinCO, which also confirms the first order of CO concentration. Particular attention is paid to the aspects of ensuring protection against carbon monoxide when its concentration exceeds 15 MPC. Usually, special equipment, such as filtering self-rescuers, is used to clean the air from carbon monoxide at concentrations from 1000 to 6500 mg/m3. The catalyst developed by us is intended for use in lightweight personal respiratory protective equipment (RPE) at concentrations not exceeding 15 MPC. Therefore, there was an interest in researching the possibilities of using this catalyst in the self-saving filter system. The concentration of carbon monoxide in the gas-air mixture was varied from 400 to 2500 mg/m3 in the presence of the К2PdCl4-Cu(NO3)2-КBr/300-Tr(K) system. It was established that Wst increases in direct proportion with an increase in the gas-air mixture up to 1250 mg/m3, which indicates the first order of the reaction according to carbon monoxide. It was found that at CinCO = 1000 mg/m3 only under the condition τ´ = 1.13 s (mk = 10 g) the К2PdCl4-Cu(NO3)2-KBr/Tr catalyst provides air purification below the breakthrough CO concentration (CfCO = 200 mg/m3). Experiments on the influence of SO2 on the activity of carbon monoxide oxidation catalysts have shown that they lose their activity, so in air purification systems from CO, it is necessary to provide for the stage of capturing sulfur dioxide.
- Open Access
- 21 December 2018
- Published by MDPI AG in Colloids and Interfaces
- Vol. 3 (1) , 1
Effect of Both the Phase Composition and Modification Methods on Structural-Adsorption Parameters of Dispersed Silicas
Tripoli from two Ukrainian deposits was studied in its natural and modified forms. The investigation of natural and modified tripoli involves the identification of their phase compositions through X-ray diffraction and the analysis of their water vapor adsorption-desorption isotherms. The obtained results are evidence of changes in the structural-adsorption parameters of tripoli as a result of modification. Their treatment in boiling water or acid causes apparent alterations of contents of the main phases and sizes of their crystallites, whereas their calcination causes not only the dehydroxylation of surfaces and the agglomeration of phases, but even phase transformation in the case of carbonate tripoli. After analyzing water vapor adsorption-desorption isotherms of natural and modified tripolis, some correlations between their adsorption parameters, phase compositions, main phase contents and crystallite sizes have been found.
- 21 December 2018
- Published by MDPI AG in Colloids and Interfaces
- Vol. 3 (1) , 1
Open AccessEffect of Both the Phase Composition and Modification Methods on Structural-Adsorption Parameters of Dispersed Silicas
Tripoli from two Ukrainian deposits was studied in its natural and modified forms. The investigation of natural and modified tripoli involves the identification of their phase compositions through X-ray diffraction and the analysis of their water vapor adsorption-desorption isotherms. The obtained results are evidence of changes in the structural-adsorption parameters of tripoli as a result of modification. Their treatment in boiling water or acid causes apparent alterations of contents of the main phases and sizes of their crystallites, whereas their calcination causes not only the dehydroxylation of surfaces and the agglomeration of phases, but even phase transformation in the case of carbonate tripoli. After analyzing water vapor adsorption-desorption isotherms of natural and modified tripolis, some correlations between their adsorption parameters, phase compositions, main phase contents and crystallite sizes have been found.
- Open Access
- 27 March 2017
- Published by Springer Nature in BMC Chemistry
- Vol. 11 (1) , 1-10
Acid-modified clinoptilolite as a support for palladium–copper complexes catalyzing carbon monoxide oxidation with air oxygen
Samples of natural clinoptilolite were modified by an acid–thermal method at nitric acid concentrations of 0.25, 0.5, 1.0, and 3.0 M and a contact time of 30 min. A series of catalysts, K2PdCl4–Cu(NO3)2–KBr/S (S = 0.25H-CLI, 0.5H-CLI, 1H-CLI, and 3H-CLI) was obtained. All samples were investigated by X-ray phase and thermogravimetric analysis, FT-IR spectroscopy, water vapor ad/desorption and pH metric method. Besides, K2PdCl4–Cu(NO3)2–KBr/S samples were tested in the reaction of low-temperature carbon monoxide oxidation. It have been found that, owing to special physicochemical and structural-adsorption properties of 3H-CLI, it promotes formation of the palladium–copper catalyst providing carbon monoxide oxidation at the steady-state mode down to CO concentrations lower than its maximum permissible concentration at air relative humidity varied within a wide range.
- 27 March 2017
- Published by Springer Nature in BMC Chemistry
- Vol. 11 (1) , 1-10
Open AccessAcid-modified clinoptilolite as a support for palladium–copper complexes catalyzing carbon monoxide oxidation with air oxygen
Samples of natural clinoptilolite were modified by an acid–thermal method at nitric acid concentrations of 0.25, 0.5, 1.0, and 3.0 M and a contact time of 30 min. A series of catalysts, K2PdCl4–Cu(NO3)2–KBr/S (S = 0.25H-CLI, 0.5H-CLI, 1H-CLI, and 3H-CLI) was obtained. All samples were investigated by X-ray phase and thermogravimetric analysis, FT-IR spectroscopy, water vapor ad/desorption and pH metric method. Besides, K2PdCl4–Cu(NO3)2–KBr/S samples were tested in the reaction of low-temperature carbon monoxide oxidation. It have been found that, owing to special physicochemical and structural-adsorption properties of 3H-CLI, it promotes formation of the palladium–copper catalyst providing carbon monoxide oxidation at the steady-state mode down to CO concentrations lower than its maximum permissible concentration at air relative humidity varied within a wide range.