Friedhelm Olschewski
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Friedhelm Olschewski has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Heinz Rongen
Central Institute of Engineering, Electronics, and AnalyticsElectronic Systems (ZEA-2), Forschungszentrum, Jülich, Germany
2 shared publications - Martin Kaufmann
Institute of Climate and Energy Systems - Stratosphere (ICE-4), Forschungszentrum Jülich, Jülich, Germany
2 shared publications - Tom Neubert
Institute of Technology and Engineering (ITE), Forschungszentrum Jülich, Jülich, Germany
2 shared publications Albert Adibekyan
Physikalisch-Technische Bundesanstalt, 10587 Berlin, Germany
1 shared publicationAmal Chandran
1 shared publicationBerndt Gutschwager
Physikalisch-Technische Bundesanstalt, 10587 Berlin, Germany
1 shared publication
Latest Publications
- 9 October 2026
- Published by SPIE-Intl Soc Optical Eng
- p. 6
AtmOCube: a 16U satellite mission with dual spatial heterodyne interferometers to observe gravity‑wave contributions to space‑weather variability
Space-weather impacts on satellites and space-based services are not driven by solar forcing alone, a major source of short-term variability in thermosphere–ionosphere (TI) originates from upward-propagating atmospheric gravity waves (GWs). The GW momentum fluxes, their directions, and vertical gradients strongly control how wave energy and momentum are deposited into the lower thermosphere and subsequently modulate thermospheric density, composition, and ionospheric structure. However, in the mesosphere–lower thermosphere (MLT, ~80–120km), the well-known observational “gap”, the GWs are insufficiently constrained for accurately forecasting space weather. Improving forecasts requires global, seasonally resolved constraints on mesoscale GWs in the MLT. The Atmospheric Oxygen CubeSat (AtmOCube) mission will fill this gap using a single 16U spacecraft carrying two compact, monolithic spatial heterodyne interferometers (SHIs) configured as limb sounders. Each SHI observes the O2 A-band airglow emission near 762nm and the data are used to retrieve three-dimensional (3D) temperature fields in the MLT. The highly miniaturized SHI limb-sounder implementation (building on the 6U AtmoLITE instrument concept) provides a clear path toward future multi-spacecraft constellations with improved spatiotemporal sampling. After launch in 2029 the AtmOCube mission derives key GW parameters from these 3D temperature fields (λh = 150–2000km)—including full 3D wave vectors, propagation direction, and momentum flux—without requiring coincident wind measurements.
- 9 October 2026
- Published by SPIE-Intl Soc Optical Eng
- p. 6
AtmOCube: a 16U satellite mission with dual spatial heterodyne interferometers to observe gravity‑wave contributions to space‑weather variability
Space-weather impacts on satellites and space-based services are not driven by solar forcing alone, a major source of short-term variability in thermosphere–ionosphere (TI) originates from upward-propagating atmospheric gravity waves (GWs). The GW momentum fluxes, their directions, and vertical gradients strongly control how wave energy and momentum are deposited into the lower thermosphere and subsequently modulate thermospheric density, composition, and ionospheric structure. However, in the mesosphere–lower thermosphere (MLT, ~80–120km), the well-known observational “gap”, the GWs are insufficiently constrained for accurately forecasting space weather. Improving forecasts requires global, seasonally resolved constraints on mesoscale GWs in the MLT. The Atmospheric Oxygen CubeSat (AtmOCube) mission will fill this gap using a single 16U spacecraft carrying two compact, monolithic spatial heterodyne interferometers (SHIs) configured as limb sounders. Each SHI observes the O2 A-band airglow emission near 762nm and the data are used to retrieve three-dimensional (3D) temperature fields in the MLT. The highly miniaturized SHI limb-sounder implementation (building on the 6U AtmoLITE instrument concept) provides a clear path toward future multi-spacecraft constellations with improved spatiotemporal sampling. After launch in 2029 the AtmOCube mission derives key GW parameters from these 3D temperature fields (λh = 150–2000km)—including full 3D wave vectors, propagation direction, and momentum flux—without requiring coincident wind measurements.
- 1 July 2019
- Published by SPIE-Intl Soc Optical Eng in Journal of Applied Remote Sensing
- Vol. 13 (03) , 1-17
System-on-module-based long-life electronics for remote sensing imaging with CubeSats in low-earth-orbits
CubeSats have become very popular science platforms in the past decades, leading to a continuously increasing number of developers in the academic field. For science missions, customized payload electronics have to be developed, depending on measurement tasks and requirements. Especially for the deployment of complex remote sensing payloads, state-of-the-art performance is needed to provide operational control and specific data processing, e.g., for image sensors. Highly integrated system-on-module (SoM) architectures offer low resource requirements regarding power and mass, but moderate to high processing power capabilities. However, a requirement to use a standard SoM in a satellite is to quantify its radiation tolerance. The radiation environment has been modeled, estimating the hazards at module level and reducing the risks to an acceptable level by applying appropriate mitigation techniques. This approach results in a sensor electronics design that combines hardware and software redundancies to assure system availability and reliability for long-life science missions in low earth orbits. Integrated in a miniaturized limb sounding instrument for atmospheric remote sensing imaging, the payload electronics will be deployed on a technology demonstration satellite for in-orbit verification.
- 1 July 2019
- Published by SPIE-Intl Soc Optical Eng in Journal of Applied Remote Sensing
- Vol. 13 (03) , 1-17
System-on-module-based long-life electronics for remote sensing imaging with CubeSats in low-earth-orbits
CubeSats have become very popular science platforms in the past decades, leading to a continuously increasing number of developers in the academic field. For science missions, customized payload electronics have to be developed, depending on measurement tasks and requirements. Especially for the deployment of complex remote sensing payloads, state-of-the-art performance is needed to provide operational control and specific data processing, e.g., for image sensors. Highly integrated system-on-module (SoM) architectures offer low resource requirements regarding power and mass, but moderate to high processing power capabilities. However, a requirement to use a standard SoM in a satellite is to quantify its radiation tolerance. The radiation environment has been modeled, estimating the hazards at module level and reducing the risks to an acceptable level by applying appropriate mitigation techniques. This approach results in a sensor electronics design that combines hardware and software redundancies to assure system availability and reliability for long-life science missions in low earth orbits. Integrated in a miniaturized limb sounding instrument for atmospheric remote sensing imaging, the payload electronics will be deployed on a technology demonstration satellite for in-orbit verification.
- Open Access
- 1 April 2019
- Published by SPIE-Intl Soc Optical Eng in Journal of Applied Remote Sensing
- Vol. 13 (02) , 024501-12
AtmoCube A1: airglow measurements in the mesosphere and lower thermosphere by spatial heterodyne interferometry
The University of Wuppertal and Research Center Juelich started the Development Initiative for Small Satellites Exploring Climate processes by Tomography, called DISSECT, together with German and Canadian research institutes and universities. The goal was to develop a small instrument to measure spectrally resolved radiation in the middle and upper atmospheres at high spatial resolution. The payload should be capable of deriving three-dimensional (3-D) information about atmospheric gravity wave patterns. The design should be simple with no movable parts in order to save power and to increase reliability. The instrument should fit into a small volume and should have a high optical throughput. The design should be easily adaptable to other scientific objectives.
- 1 April 2019
- Published by SPIE-Intl Soc Optical Eng in Journal of Applied Remote Sensing
- Vol. 13 (02) , 024501-12
Open AccessAtmoCube A1: airglow measurements in the mesosphere and lower thermosphere by spatial heterodyne interferometry
The University of Wuppertal and Research Center Juelich started the Development Initiative for Small Satellites Exploring Climate processes by Tomography, called DISSECT, together with German and Canadian research institutes and universities. The goal was to develop a small instrument to measure spectrally resolved radiation in the middle and upper atmospheres at high spatial resolution. The payload should be capable of deriving three-dimensional (3-D) information about atmospheric gravity wave patterns. The design should be simple with no movable parts in order to save power and to increase reliability. The instrument should fit into a small volume and should have a high optical throughput. The design should be easily adaptable to other scientific objectives.
- Open Access
- 14 August 2018
- Published by Copernicus GmbH in Atmospheric Measurement Techniques
- Vol. 11 (8) , 4757-4762
A large-area blackbody for in-flight calibration of an infrared interferometer deployed on board a long-duration balloon for stratospheric research
The deployment of the imaging Fourier Transform Spectrometer GLORIA (Gimballed Limb Observer for Radiance Imaging of the Atmosphere) on board a long-duration balloon for stratospheric research requires a blackbody for in-flight calibration in order to provide traceability to the International Temperature Scale (ITS-90) to ensure comparability with the results of other experiments and over time. GLORIA, which has been deployed onboard various research aircraft such as the Russian M55 Geophysica or the German HALO in the past, shall also be used for detailed atmospheric measurements in the stratosphere up to 40 km altitude. The instrument uses a two-dimensional detector array and an imaging optics with a large aperture diameter of 36 mm and an opening angle of 4.07∘ × 4.07∘ for infrared limb observations. To overfill the field of view (FOV) of the instrument, a large-area blackbody radiation sources (125 mm × 125 mm) is required for in-flight calibration. In order to meet the requirements regarding the scientific goals of the GLORIA missions, the radiance temperature of the blackbody calibration source has to be determined to better than 100 mK and the spatial temperature uniformity shall be better than 150 mK. As electrical resources on board a stratospheric balloon are very limited, the latent heat of the phase change of a eutectic material is utilized for temperature stabilization of the calibration source, such that the blackbody has a constant temperature of about −32 ∘C corresponding to a typical temperature observed in the stratosphere. The Institute for Atmospheric and Environmental Research at the University of Wuppertal designed and manufactured a prototype of the large-area blackbody for in-flight calibration of an infrared interferometer deployed on board a long-duration balloon for stratospheric research. This newly developed calibration source was tested under lab conditions as well as in a climatic and environmental test chamber in order to verify its performance especially under flight conditions. At the PTB (Physikalisch-Technische Bundesanstalt), the German national metrology institute, the spatial radiance distribution of the blackbody was determined and traceability to the International Temperature Scale (ITS-90) has been assured. In this paper the design and performance of the balloon-borne blackbody (BBB) is presented.
- 14 August 2018
- Published by Copernicus GmbH in Atmospheric Measurement Techniques
- Vol. 11 (8) , 4757-4762
Open AccessA large-area blackbody for in-flight calibration of an infrared interferometer deployed on board a long-duration balloon for stratospheric research
The deployment of the imaging Fourier Transform Spectrometer GLORIA (Gimballed Limb Observer for Radiance Imaging of the Atmosphere) on board a long-duration balloon for stratospheric research requires a blackbody for in-flight calibration in order to provide traceability to the International Temperature Scale (ITS-90) to ensure comparability with the results of other experiments and over time. GLORIA, which has been deployed onboard various research aircraft such as the Russian M55 Geophysica or the German HALO in the past, shall also be used for detailed atmospheric measurements in the stratosphere up to 40 km altitude. The instrument uses a two-dimensional detector array and an imaging optics with a large aperture diameter of 36 mm and an opening angle of 4.07∘ × 4.07∘ for infrared limb observations. To overfill the field of view (FOV) of the instrument, a large-area blackbody radiation sources (125 mm × 125 mm) is required for in-flight calibration. In order to meet the requirements regarding the scientific goals of the GLORIA missions, the radiance temperature of the blackbody calibration source has to be determined to better than 100 mK and the spatial temperature uniformity shall be better than 150 mK. As electrical resources on board a stratospheric balloon are very limited, the latent heat of the phase change of a eutectic material is utilized for temperature stabilization of the calibration source, such that the blackbody has a constant temperature of about −32 ∘C corresponding to a typical temperature observed in the stratosphere. The Institute for Atmospheric and Environmental Research at the University of Wuppertal designed and manufactured a prototype of the large-area blackbody for in-flight calibration of an infrared interferometer deployed on board a long-duration balloon for stratospheric research. This newly developed calibration source was tested under lab conditions as well as in a climatic and environmental test chamber in order to verify its performance especially under flight conditions. At the PTB (Physikalisch-Technische Bundesanstalt), the German national metrology institute, the spatial radiance distribution of the blackbody was determined and traceability to the International Temperature Scale (ITS-90) has been assured. In this paper the design and performance of the balloon-borne blackbody (BBB) is presented.