Kirill A. Konnov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kirill A. Konnov has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
- Sergey V. Varzhel
ITMO University
15 shared publications - Dmitriy A. Konnov
ITMO University
6 shared publications A. I. Gribaev
ITMO University, St. Petersburg, Russia
4 shared publicationsA.I. Gribaev
ITMO University, 197101, St. Petersburg, Russia
3 shared publicationsA. A. Petrov
ITMO University
2 shared publications- A. I. Gribaev
ITMO University, St. Petersburg, Russia
2 shared publications
Latest Publications
- 1 September 2025
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 92 (9)
Development and investigation of a fiber-optic Fabry–Pérot interferometer with an air cavity between the resonator mirrors
Subject of study . A fiber-optic Fabry–Pérot interferometer (FPI) with an air cavity between the resonator mirrors is studied. Aim of study . A fiber-optic FPI with an air cavity between the resonator mirrors is designed and fabricated, achieving an increase in the visibility of the interference pattern and the free spectral range. Method . The FPI contains two collimating structures with resonator mirrors coaxially aligned and separated along the optical axis. Each structure includes a coaxially connected optical fiber and a gradient lens formed by a section of a multimode graded-index optical fiber. The opposite polished end face of the gradient lens with a reflective coating forms the reflective surface of the interferometer resonator. Main results . Interferometer samples with air cavity lengths ranging from 0.5 mm to 5 mm (increased in 0.5 mm steps) were fabricated. The visibility of the interference pattern in the wavelength range of 1300–1310 nm ranged from 0.989 to 0.679, and the free spectral range ranged from 1.707 nm to 0.178 nm. Practical significance . The developed interferometer can be applied as a sensing element in a refractive index sensor for measuring the refractive indices of gases and liquids in the range from 1 to 1.47 with a sensitivity of 190.4 pm/RIU.
- 1 September 2025
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 92 (9)
Development and investigation of a fiber-optic Fabry–Pérot interferometer with an air cavity between the resonator mirrors
Subject of study . A fiber-optic Fabry–Pérot interferometer (FPI) with an air cavity between the resonator mirrors is studied. Aim of study . A fiber-optic FPI with an air cavity between the resonator mirrors is designed and fabricated, achieving an increase in the visibility of the interference pattern and the free spectral range. Method . The FPI contains two collimating structures with resonator mirrors coaxially aligned and separated along the optical axis. Each structure includes a coaxially connected optical fiber and a gradient lens formed by a section of a multimode graded-index optical fiber. The opposite polished end face of the gradient lens with a reflective coating forms the reflective surface of the interferometer resonator. Main results . Interferometer samples with air cavity lengths ranging from 0.5 mm to 5 mm (increased in 0.5 mm steps) were fabricated. The visibility of the interference pattern in the wavelength range of 1300–1310 nm ranged from 0.989 to 0.679, and the free spectral range ranged from 1.707 nm to 0.178 nm. Practical significance . The developed interferometer can be applied as a sensing element in a refractive index sensor for measuring the refractive indices of gases and liquids in the range from 1 to 1.47 with a sensitivity of 190.4 pm/RIU.
- 1 March 2025
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 92 (3) , 165-169
Examining the generation modes of an erbium-doped fiber laser with distributed feedback
Subject of study. The subject of this study is the analysis of the parameters and optical characteristics of a distributed feedback (DFB) laser based on a single fiber Bragg grating (FBG) with a constant period inscribed in an erbium-doped optical fiber. Aim of study. The aim was to determine the dependence of the radiation generation mode of a DFB laser, based on a single FBG with a constant period recorded using the phase mask method, on the pump power and resonator length. Method. FBGs were inscribed using the phase mask method via optical beam translation of a KrF excimer laser with a central wavelength of 248 nm. Structures with lengths ranging from 40 mm to 70 mm (in 5 mm steps) and reflection coefficients exceeding 99% were recorded in a FiberCore I-25(980/125) optical fiber under low-temperature hydrogen loading. A pump diode, with a central wavelength and maximum output of 980 nm and 435 mW, respectively, was used. The correlations between the radiation parameters and variations in the FBG length and pump power were measured. Main results. The variations in the generation mode of the DFB laser on pump and resonator parameters were analyzed. The results showed that stable radiation can be generated, at pump powers up to 435 mW, using a single 45-mm-long FBG with a constant period (recorded using the phase mask method in an erbium-doped fiber), without requiring π -phase-shifted structures or longer gratings (recorded using the step-by-step method). Practical significance. The results obtained can be applied to simplify optical schemes and optimize the performance of measurement systems based on DFB fiber lasers.
- 1 March 2025
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 92 (3) , 165-169
Examining the generation modes of an erbium-doped fiber laser with distributed feedback
Subject of study. The subject of this study is the analysis of the parameters and optical characteristics of a distributed feedback (DFB) laser based on a single fiber Bragg grating (FBG) with a constant period inscribed in an erbium-doped optical fiber. Aim of study. The aim was to determine the dependence of the radiation generation mode of a DFB laser, based on a single FBG with a constant period recorded using the phase mask method, on the pump power and resonator length. Method. FBGs were inscribed using the phase mask method via optical beam translation of a KrF excimer laser with a central wavelength of 248 nm. Structures with lengths ranging from 40 mm to 70 mm (in 5 mm steps) and reflection coefficients exceeding 99% were recorded in a FiberCore I-25(980/125) optical fiber under low-temperature hydrogen loading. A pump diode, with a central wavelength and maximum output of 980 nm and 435 mW, respectively, was used. The correlations between the radiation parameters and variations in the FBG length and pump power were measured. Main results. The variations in the generation mode of the DFB laser on pump and resonator parameters were analyzed. The results showed that stable radiation can be generated, at pump powers up to 435 mW, using a single 45-mm-long FBG with a constant period (recorded using the phase mask method in an erbium-doped fiber), without requiring π -phase-shifted structures or longer gratings (recorded using the step-by-step method). Practical significance. The results obtained can be applied to simplify optical schemes and optimize the performance of measurement systems based on DFB fiber lasers.
- 1 December 2024
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 91 (12) , 814-817
Development and analysis of a fiber-optic temperature sensor based on two superposed regenerated fiber Bragg gratings
Subject of study. A fiber-optic temperature sensor based on two superposed regenerated fiber Bragg gratings is studied. Aim of study. A fiber-optic temperature sensor with a range of +25∘C to +1000∘C based on two superposed regenerated fiber Bragg gratings is developed, and the temperature sensitivity of the resulting sensor is determined. Method. Two superposed standard fiber Bragg gratings (length of 14 mm) with reflectivities of 90% and 70% were heated (heating rate of 500°C/h) from room temperature to the regeneration temperature of 920°C, appropriate for optical fibers meeting the G.657.A2 standard; the gratings were held at this temperature pending complete formation of the regenerated structure. Main results. The development effort and thermal studies (which were performed over a temperature range from +25∘C to +1000∘C with steps of 100°C) led to the development of a fiber-optic temperature sensor based on superposed regenerated fiber Bragg gratings with reflectance and temperature sensitivities of approximately 40% and 12.7 pm/°C and approximately 30% and 12.72 pm/°C, respectively. Practical significance. This paper marks the first, to our knowledge, successful superposition of two regenerated fiber Bragg gratings with reflection coefficients greater than 40% and 30%. The sensor developed based on this structure has a wider temperature measurement range with a narrow range of probe wavelengths. This paper also marks the first determination of the temperature sensitivity of a regenerated fiber Bragg grating as a function of its central reflection wavelength.
- 1 December 2024
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 91 (12) , 814-817
Development and analysis of a fiber-optic temperature sensor based on two superposed regenerated fiber Bragg gratings
Subject of study. A fiber-optic temperature sensor based on two superposed regenerated fiber Bragg gratings is studied. Aim of study. A fiber-optic temperature sensor with a range of +25∘C to +1000∘C based on two superposed regenerated fiber Bragg gratings is developed, and the temperature sensitivity of the resulting sensor is determined. Method. Two superposed standard fiber Bragg gratings (length of 14 mm) with reflectivities of 90% and 70% were heated (heating rate of 500°C/h) from room temperature to the regeneration temperature of 920°C, appropriate for optical fibers meeting the G.657.A2 standard; the gratings were held at this temperature pending complete formation of the regenerated structure. Main results. The development effort and thermal studies (which were performed over a temperature range from +25∘C to +1000∘C with steps of 100°C) led to the development of a fiber-optic temperature sensor based on superposed regenerated fiber Bragg gratings with reflectance and temperature sensitivities of approximately 40% and 12.7 pm/°C and approximately 30% and 12.72 pm/°C, respectively. Practical significance. This paper marks the first, to our knowledge, successful superposition of two regenerated fiber Bragg gratings with reflection coefficients greater than 40% and 30%. The sensor developed based on this structure has a wider temperature measurement range with a narrow range of probe wavelengths. This paper also marks the first determination of the temperature sensitivity of a regenerated fiber Bragg grating as a function of its central reflection wavelength.
- 1 May 2024
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 91 (5) , 330-333
Development and analysis of a fiber-optic temperature sensor based on a regenerated fiber Bragg grating
Subject of study. A fiber-optic temperature sensor based on regenerated fiber Bragg gratings is studied. Aim of study. A high-temperature sensor based on a regenerated fiber Bragg grating is developed, and a thermal study of the sensor up to a temperature of 1000°C is performed. Method. The regenerated fiber Bragg grating was produced by annealing a “seed” fiber Bragg grating recorded on SMF-28 hydrogen-loaded optical fiber in a high-temperature muffle furnace at a continuously rising temperature from room temperature to 920°C (the regeneration temperature in the case of SMF-28 fiber). The reflection coefficient of the “seed” grating was as close to 100% as possible, with a structure length of 15 mm. The heating rate was 500 deg/h. Main results. During the work and thermal studies described above, which were performed over a temperature range from +25∘C to +1000∘C with steps of 100°C, a fiber-optic temperature sensor was developed based on a regenerated fiber Bragg grating with a reflectance of about 50% and a temperature sensitivity of 14.9 pm/°C. Practical significance. The proposed method for manufacturing regenerated fiber Bragg gratings enables them to be used as the sensing element in a temperature sensor. The ability to operate at such high temperatures opens up broad potential for application to a wide range of industrial applications (such as gas turbine engines, power plants, steel mills, etc.). This method enables a fiber-optic temperature sensor to be constructed without using additional equipment or materials.
- 1 May 2024
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 91 (5) , 330-333
Development and analysis of a fiber-optic temperature sensor based on a regenerated fiber Bragg grating
Subject of study. A fiber-optic temperature sensor based on regenerated fiber Bragg gratings is studied. Aim of study. A high-temperature sensor based on a regenerated fiber Bragg grating is developed, and a thermal study of the sensor up to a temperature of 1000°C is performed. Method. The regenerated fiber Bragg grating was produced by annealing a “seed” fiber Bragg grating recorded on SMF-28 hydrogen-loaded optical fiber in a high-temperature muffle furnace at a continuously rising temperature from room temperature to 920°C (the regeneration temperature in the case of SMF-28 fiber). The reflection coefficient of the “seed” grating was as close to 100% as possible, with a structure length of 15 mm. The heating rate was 500 deg/h. Main results. During the work and thermal studies described above, which were performed over a temperature range from +25∘C to +1000∘C with steps of 100°C, a fiber-optic temperature sensor was developed based on a regenerated fiber Bragg grating with a reflectance of about 50% and a temperature sensitivity of 14.9 pm/°C. Practical significance. The proposed method for manufacturing regenerated fiber Bragg gratings enables them to be used as the sensing element in a temperature sensor. The ability to operate at such high temperatures opens up broad potential for application to a wide range of industrial applications (such as gas turbine engines, power plants, steel mills, etc.). This method enables a fiber-optic temperature sensor to be constructed without using additional equipment or materials.
- 1 September 2023
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 90 (9) , 528-532
Development and studies of a fiber-optic temperature sensor based on a Fabry–Perot interferometer obtained by welding optical fibers
Subject of study. A fiber-optic temperature sensor, based on a Fabry–Perot interferometer obtained by welding optical fibers, is developed and characterized. Aim of study. The aim is to develop and characterize a temperature sensor based on a fiber-optic Fabry–Perot interferometer obtained by arc welding and evaluate its temperature-sensing performance. Method. The design of the temperature sensor is implemented based on a Fabry–Perot interferometer obtained by welding optical fibers. The reflecting mirrors of the sensor comprise layers of thin films of titanium dioxide. The interferometer interrogation method is based on the use of a vertically emitting laser operating in the pulsed generation mode. The principle of registering the phase shift between radiation reflected from the interferometer mirrors with changes in temperature is based on auxiliary modulation of the laser radiation wavelength due to a periodic change in the pulse duration. Main results. During the temperature evaluation of the developed sensor, the phase characteristics of the Fabry–Perot interferometer were obtained in the temperature range of +20∘C to +380∘C. A shift in the operating point was registered with changes in the ambient temperature. The results of the experiment indicated that an increase in the ambient temperature leads to an increase in phase difference between the radiation reflected from the first and second mirrors of the interferometer. Results suggest that the phase sensitivity to temperature change is 0.96, 1.68, and 2.35 rad/°C at distances between mirrors corresponding to 5, 8, and 11 mm, respectively. Practical significance. The proposed fabrication method for the Fabry–Perot interferometer provides sufficient opportunities for the formation of a resonator with different lengths and also makes it possible to exclude the use of additional materials in its design. Hence, the interferometer exhibits small weight and size parameters, and thus, it can be used in a wide range of applications, including as a sensitive element of a temperature sensor. The sensor interrogation method employed in the study eliminates the need for costly spectral measuring instruments such as optical spectrum analyzers and interrogators.
- 1 September 2023
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 90 (9) , 528-532
Development and studies of a fiber-optic temperature sensor based on a Fabry–Perot interferometer obtained by welding optical fibers
Subject of study. A fiber-optic temperature sensor, based on a Fabry–Perot interferometer obtained by welding optical fibers, is developed and characterized. Aim of study. The aim is to develop and characterize a temperature sensor based on a fiber-optic Fabry–Perot interferometer obtained by arc welding and evaluate its temperature-sensing performance. Method. The design of the temperature sensor is implemented based on a Fabry–Perot interferometer obtained by welding optical fibers. The reflecting mirrors of the sensor comprise layers of thin films of titanium dioxide. The interferometer interrogation method is based on the use of a vertically emitting laser operating in the pulsed generation mode. The principle of registering the phase shift between radiation reflected from the interferometer mirrors with changes in temperature is based on auxiliary modulation of the laser radiation wavelength due to a periodic change in the pulse duration. Main results. During the temperature evaluation of the developed sensor, the phase characteristics of the Fabry–Perot interferometer were obtained in the temperature range of +20∘C to +380∘C. A shift in the operating point was registered with changes in the ambient temperature. The results of the experiment indicated that an increase in the ambient temperature leads to an increase in phase difference between the radiation reflected from the first and second mirrors of the interferometer. Results suggest that the phase sensitivity to temperature change is 0.96, 1.68, and 2.35 rad/°C at distances between mirrors corresponding to 5, 8, and 11 mm, respectively. Practical significance. The proposed fabrication method for the Fabry–Perot interferometer provides sufficient opportunities for the formation of a resonator with different lengths and also makes it possible to exclude the use of additional materials in its design. Hence, the interferometer exhibits small weight and size parameters, and thus, it can be used in a wide range of applications, including as a sensitive element of a temperature sensor. The sensor interrogation method employed in the study eliminates the need for costly spectral measuring instruments such as optical spectrum analyzers and interrogators.
- Open Access
- 1 June 2022
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 22 (3) , 442
High-precision fiber-optic temperature sensor based on Fabry-Perot interferometer with reflective thin-film multilayer structures
- 1 June 2022
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 22 (3) , 442
Open AccessHigh-precision fiber-optic temperature sensor based on Fabry-Perot interferometer with reflective thin-film multilayer structures
- 1 September 2018
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 85 (9) , 531-534
Inscription and investigation of the spectral characteristics of chirped fiber Bragg gratings
The results of investigations of the spectral characteristics of chirped fiber Bragg gratings induced in an optical fiber using a Talbot interferometer and a KrF excimer laser system of the master oscillator–power amplifier type with enhanced coherence are presented. Dependences of the full width of the reflection spectrum at half maximum and the reflectivity of chirped fiber Bragg gratings on their length are obtained and analyzed. Through the inscription of seven superimposed chirped fiber Bragg gratings, a diffraction structure with a spectral width of 32 nm was obtained. In addition, a chirped fiber Bragg grating whose spectral response shape is almost rectangular is presented.
- 1 September 2018
- Published by Optica Publishing Group in Journal of Optical Technology
- Vol. 85 (9) , 531-534
Inscription and investigation of the spectral characteristics of chirped fiber Bragg gratings
The results of investigations of the spectral characteristics of chirped fiber Bragg gratings induced in an optical fiber using a Talbot interferometer and a KrF excimer laser system of the master oscillator–power amplifier type with enhanced coherence are presented. Dependences of the full width of the reflection spectrum at half maximum and the reflectivity of chirped fiber Bragg gratings on their length are obtained and analyzed. Through the inscription of seven superimposed chirped fiber Bragg gratings, a diffraction structure with a spectral width of 32 nm was obtained. In addition, a chirped fiber Bragg grating whose spectral response shape is almost rectangular is presented.
- 1 July 2018
- Published by Pleiades Publishing Ltd in Optics and Spectroscopy
- Vol. 125 (1) , 54-59
Inscription and Visualization of Tilted Fiber Bragg Gratings
Tilted fiber Bragg gratings with different tilt angles have been inscribed in single-mode isotropic optical fiber with an increased photorefractivity using Talbot interferometer and KrF-excimer laser...
- 1 July 2018
- Published by Pleiades Publishing Ltd in Optics and Spectroscopy
- Vol. 125 (1) , 54-59
Inscription and Visualization of Tilted Fiber Bragg Gratings
Tilted fiber Bragg gratings with different tilt angles have been inscribed in single-mode isotropic optical fiber with an increased photorefractivity using Talbot interferometer and KrF-excimer laser...
- Open Access
- 14 June 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1038 (1) , 012095
Phase-shifted fiber Bragg gratings fabrication method
In this paper, we showed a technique for the formation of phase-shifted fiber Bragg gratings. The analysis of the efficiency of the obtained structures was carried out with the help of an optical spectrum analyzer with the subsequent calculation of the full width at half maximum of a bandpass in reflection spectrum. Fiber Bragg gratings inscription was performed on the Talbot interferometer, the KrF excimer laser system was used as a UV radiation source, and a phase shift was introduced by the electrical discharge of an arc fusion splicer. The experimental dependence between the length of the obtained structure and the full width at half maximum of a bandpass in reflection spectrum of a phase-shifted grating was presented, the value of the last parameter varies in the range from 24 pm to 96 pm.
- 14 June 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1038 (1) , 012095
Open AccessPhase-shifted fiber Bragg gratings fabrication method
In this paper, we showed a technique for the formation of phase-shifted fiber Bragg gratings. The analysis of the efficiency of the obtained structures was carried out with the help of an optical spectrum analyzer with the subsequent calculation of the full width at half maximum of a bandpass in reflection spectrum. Fiber Bragg gratings inscription was performed on the Talbot interferometer, the KrF excimer laser system was used as a UV radiation source, and a phase shift was introduced by the electrical discharge of an arc fusion splicer. The experimental dependence between the length of the obtained structure and the full width at half maximum of a bandpass in reflection spectrum of a phase-shifted grating was presented, the value of the last parameter varies in the range from 24 pm to 96 pm.
- Open Access
- 14 June 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1038 (1) , 012077
Inscription and visualization of tilted fiber Bragg gratings
In this work the inscription and investigation of tilted fiber Bragg gratings induced in a single-mode isotropic optical fiber with increased photorefractivity are demonstrated. Using the Talbot interferometer and the KrF excimer laser system, tilted fiber Bragg gratings with different angles were fabricated, the spectra of the formed diffraction structures were analyzed, and their photographic images were taken with a confocal laser scanning fluorescence microscope in transmitted light. The calculated dependence of the tilt angle of tilted fiber Bragg gratings fabricated in the Talbot interferometer on the angle between the interference fringes created in the interferometer and the cross section of the optical fiber is experimentally verified.
- 14 June 2018
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1038 (1) , 012077
Open AccessInscription and visualization of tilted fiber Bragg gratings
In this work the inscription and investigation of tilted fiber Bragg gratings induced in a single-mode isotropic optical fiber with increased photorefractivity are demonstrated. Using the Talbot interferometer and the KrF excimer laser system, tilted fiber Bragg gratings with different angles were fabricated, the spectra of the formed diffraction structures were analyzed, and their photographic images were taken with a confocal laser scanning fluorescence microscope in transmitted light. The calculated dependence of the tilt angle of tilted fiber Bragg gratings fabricated in the Talbot interferometer on the angle between the interference fringes created in the interferometer and the cross section of the optical fiber is experimentally verified.