DKDmitriy A. Konnov

Dmitriy A. Konnov

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Dmitriy A. Konnov has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Development and investigation of a fiber-optic Fabry–Pérot interferometer with an air cavity between the resonator mirrors

    by Dmitriy A. Konnov, Sergey V. Varzhel, Kirill A. Konnov

    Subject of study . A fiber-optic Fabry–Pérot interferometer (FPI) with an air cavity between the resonator mirrors is studied. Aim of study . A fiber-optic FPI with an air cavity between the resonator mirrors is designed and fabricated, achieving an increase in the visibility of the interference pattern and the free spectral range. Method . The FPI contains two collimating structures with resonator mirrors coaxially aligned and separated along the optical axis. Each structure includes a coaxially connected optical fiber and a gradient lens formed by a section of a multimode graded-index optical fiber. The opposite polished end face of the gradient lens with a reflective coating forms the reflective surface of the interferometer resonator. Main results . Interferometer samples with air cavity lengths ranging from 0.5 mm to 5 mm (increased in 0.5 mm steps) were fabricated. The visibility of the interference pattern in the wavelength range of 1300–1310 nm ranged from 0.989 to 0.679, and the free spectral range ranged from 1.707 nm to 0.178 nm. Practical significance . The developed interferometer can be applied as a sensing element in a refractive index sensor for measuring the refractive indices of gases and liquids in the range from 1 to 1.47 with a sensitivity of 190.4 pm/RIU.

  • Examining the generation modes of an erbium-doped fiber laser with distributed feedback

    by Ianina D. Moor, Andrei V. Kulikov, Dmitrii A. Konnov, Kirill A. Konnov, Irina A. Veremeenko, Vladislav V. Savin

    Subject of study. The subject of this study is the analysis of the parameters and optical characteristics of a distributed feedback (DFB) laser based on a single fiber Bragg grating (FBG) with a constant period inscribed in an erbium-doped optical fiber. Aim of study. The aim was to determine the dependence of the radiation generation mode of a DFB laser, based on a single FBG with a constant period recorded using the phase mask method, on the pump power and resonator length. Method. FBGs were inscribed using the phase mask method via optical beam translation of a KrF excimer laser with a central wavelength of 248 nm. Structures with lengths ranging from 40 mm to 70 mm (in 5 mm steps) and reflection coefficients exceeding 99% were recorded in a FiberCore I-25(980/125) optical fiber under low-temperature hydrogen loading. A pump diode, with a central wavelength and maximum output of 980 nm and 435 mW, respectively, was used. The correlations between the radiation parameters and variations in the FBG length and pump power were measured. Main results. The variations in the generation mode of the DFB laser on pump and resonator parameters were analyzed. The results showed that stable radiation can be generated, at pump powers up to 435 mW, using a single 45-mm-long FBG with a constant period (recorded using the phase mask method in an erbium-doped fiber), without requiring π -phase-shifted structures or longer gratings (recorded using the step-by-step method). Practical significance. The results obtained can be applied to simplify optical schemes and optimize the performance of measurement systems based on DFB fiber lasers.

  • Development of a fiber-optic temperature sensor based on chirped Bragg gratings and modulation of optical radiation intensity

    by Anna L. Voloshina, Ulyana R. Korobkova, Dmitry A. Konnov, Sergey V. Varzhel, Evgenii E. Karpov

    Subject of study. A fiber-optic temperature sensor based on measurement of the reflected optical power is studied. Aim of study. A fabrication technique for fiber-optic temperature sensors based on chirped fiber Bragg gratings and measuring the reflected optical power is developed. Method. The fiber-optic temperature sensor consists of a brass probe with two chirped Bragg gratings, one of which is also enclosed in a steel capillary tube and has higher temperature sensitivity than the other grating. Changes in temperature modulate the overlap between the spectra from the first and second Bragg gratings, enabling detection of changes in the optical power reflected by the structures. Main results. An approach is being developed for creating a fiber-optic temperature sensor based on measurement of optical radiation intensity. The sensor has a design operating range of −20∘C to +80∘C. The sensor was tested by varying the temperature from −20∘C to +80∘C in 10°C intervals, revealing a sensor sensitivity of −0.015dB/∘C. The sensor was also found to have a temperature measurement error of 1.0% (relative to a thermocouple). The deviation in the sensor readings at a steady temperature value is estimated to be 0.06°C. Practical significance. The temperature sensor developed herein is part of the worldwide trend towards cost-effective design solutions. This measurement technique based on modulation of the optical intensity enables the use of a readily available interrogation scheme that does not require expensive equipment such as an optical spectrum analyzer or interrogator. This interrogation scheme also has the advantages of high data recording speed, relatively simple design, and the absence of strict requirements with respect to operating conditions.

  • Development and analysis of a fiber-optic temperature sensor based on two superposed regenerated fiber Bragg gratings

    by Dmitriy A. Konnov, Irina D. Kazachkova, Kirill A. Konnov, Varvara A. Kulikova, Sergey V. Varzhel

    Subject of study. A fiber-optic temperature sensor based on two superposed regenerated fiber Bragg gratings is studied. Aim of study. A fiber-optic temperature sensor with a range of +25∘C to +1000∘C based on two superposed regenerated fiber Bragg gratings is developed, and the temperature sensitivity of the resulting sensor is determined. Method. Two superposed standard fiber Bragg gratings (length of 14 mm) with reflectivities of 90% and 70% were heated (heating rate of 500°C/h) from room temperature to the regeneration temperature of 920°C, appropriate for optical fibers meeting the G.657.A2 standard; the gratings were held at this temperature pending complete formation of the regenerated structure. Main results. The development effort and thermal studies (which were performed over a temperature range from +25∘C to +1000∘C with steps of 100°C) led to the development of a fiber-optic temperature sensor based on superposed regenerated fiber Bragg gratings with reflectance and temperature sensitivities of approximately 40% and 12.7 pm/°C and approximately 30% and 12.72 pm/°C, respectively. Practical significance. This paper marks the first, to our knowledge, successful superposition of two regenerated fiber Bragg gratings with reflection coefficients greater than 40% and 30%. The sensor developed based on this structure has a wider temperature measurement range with a narrow range of probe wavelengths. This paper also marks the first determination of the temperature sensitivity of a regenerated fiber Bragg grating as a function of its central reflection wavelength.


  • Development and analysis of a fiber-optic temperature sensor based on a regenerated fiber Bragg grating

    by Dmitriy A. Konnov, Irina D. Kazachkova, Kirill A. Konnov, Varvara A. Kulikova, Sergey V. Varzhel

    Subject of study. A fiber-optic temperature sensor based on regenerated fiber Bragg gratings is studied. Aim of study. A high-temperature sensor based on a regenerated fiber Bragg grating is developed, and a thermal study of the sensor up to a temperature of 1000°C is performed. Method. The regenerated fiber Bragg grating was produced by annealing a “seed” fiber Bragg grating recorded on SMF-28 hydrogen-loaded optical fiber in a high-temperature muffle furnace at a continuously rising temperature from room temperature to 920°C (the regeneration temperature in the case of SMF-28 fiber). The reflection coefficient of the “seed” grating was as close to 100% as possible, with a structure length of 15 mm. The heating rate was 500 deg/h. Main results. During the work and thermal studies described above, which were performed over a temperature range from +25∘C to +1000∘C with steps of 100°C, a fiber-optic temperature sensor was developed based on a regenerated fiber Bragg grating with a reflectance of about 50% and a temperature sensitivity of 14.9 pm/°C. Practical significance. The proposed method for manufacturing regenerated fiber Bragg gratings enables them to be used as the sensing element in a temperature sensor. The ability to operate at such high temperatures opens up broad potential for application to a wide range of industrial applications (such as gas turbine engines, power plants, steel mills, etc.). This method enables a fiber-optic temperature sensor to be constructed without using additional equipment or materials.


  • Development and studies of a fiber-optic temperature sensor based on a Fabry–Perot interferometer obtained by welding optical fibers

    by D. A. Konnov, I. D. Kazachkova, V. V. Savin, A. L. Voloshina, K. A. Konnov, M. Y. Plotnikov, S. V. Varzhel

    Subject of study. A fiber-optic temperature sensor, based on a Fabry–Perot interferometer obtained by welding optical fibers, is developed and characterized. Aim of study. The aim is to develop and characterize a temperature sensor based on a fiber-optic Fabry–Perot interferometer obtained by arc welding and evaluate its temperature-sensing performance. Method. The design of the temperature sensor is implemented based on a Fabry–Perot interferometer obtained by welding optical fibers. The reflecting mirrors of the sensor comprise layers of thin films of titanium dioxide. The interferometer interrogation method is based on the use of a vertically emitting laser operating in the pulsed generation mode. The principle of registering the phase shift between radiation reflected from the interferometer mirrors with changes in temperature is based on auxiliary modulation of the laser radiation wavelength due to a periodic change in the pulse duration. Main results. During the temperature evaluation of the developed sensor, the phase characteristics of the Fabry–Perot interferometer were obtained in the temperature range of +20∘C to +380∘C. A shift in the operating point was registered with changes in the ambient temperature. The results of the experiment indicated that an increase in the ambient temperature leads to an increase in phase difference between the radiation reflected from the first and second mirrors of the interferometer. Results suggest that the phase sensitivity to temperature change is 0.96, 1.68, and 2.35 rad/°C at distances between mirrors corresponding to 5, 8, and 11 mm, respectively. Practical significance. The proposed fabrication method for the Fabry–Perot interferometer provides sufficient opportunities for the formation of a resonator with different lengths and also makes it possible to exclude the use of additional materials in its design. Hence, the interferometer exhibits small weight and size parameters, and thus, it can be used in a wide range of applications, including as a sensitive element of a temperature sensor. The sensor interrogation method employed in the study eliminates the need for costly spectral measuring instruments such as optical spectrum analyzers and interrogators.


  • Development of a direct phase demodulation method for a Fabry-Pérot interferometer for temperature measurements using frequency scanning

    by Irina D. Kazachkova, Michael Y. Plotnikov, Kirill A. Konnov, Dmitriy A. Konnov

    Subject of study. The spectral characteristics of an interference signal were studied using the method of direct phase demodulation on the interrogator of a fiber-optic sensor for high-temperature measurements. The aim of the study is to develop a method for measuring the absolute temperature of a Fabry–Pérot interferometer, based on phase demodulation using frequency scanning. Method. A mathematical model for direct phase demodulation was implemented in MATLAB. This model allows us to evaluate the change in the optical length of the interferometer under the influence of temperature by performing frequency modulation of the wavelength of the optical source according to the periodic sawtooth law. Owing to the multipath interference in the resonator of the Fabry–Pérot interferometer, the photodetector registers a reflected interference response with a complex spectral composition. The current value of the phase difference in the interferometer is restored by the estimation of the local minimum position of the interference signal, and the absolute temperature of the interferometer is thus determined.Main results. The mathematical model was applied to a wavelength range of 1308–1310 nm of the optical source. The length of the interferometer resonator was matched to the allowable range of the vertical-cavity surface-emitting laser wavelength tuning to achieve the maximum phase sensitivity. A digital filter for the phase demodulation method of the Fabry–Pérot interferometer was selected, and the potential accuracy of the temperature determination method was calculated considering the presence of noise in the measuring system. Practical significance. The proposed method can be used in the interrogation system of fiber-optic interferometric Fabry–Pérot sensors, as well as for high-precision temperature (above 300°C) monitoring systems.