Philipe Augusto de Paula Pacheco
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Philipe Augusto de Paula Pacheco has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Auteliano Antunes dos Santos
3 shared publicationsMatheus Valente Lopes
3 shared publications- Auteliano Antunes Santos
DSI/FEM, Universidade Estadual de Campinas (UNICAMP), Rua Mendeleyev, 200, Campinas, São Paulo, Brazil
2 shared publications - Matheus Valente Lopes
University of Campinas (Unicamp
2 shared publications - Márcio Eduardo Silveira
Federal University of São João del Rei, São João del Rei, Brazil
2 shared publications Thairon Reis
University of Campinas (Unicamp
2 shared publications
Latest Publications
- 25 February 2026
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48 (3) , 234
Impact of track quality and braking strategies on energy consumption in heavy-haul trains
- 25 February 2026
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48 (3) , 234
Impact of track quality and braking strategies on energy consumption in heavy-haul trains
- Open Access
- 20 February 2026
- Published by Elsevier in Heavy Rail
- Vol. 1
A simplified framework for sensitivity analysis of energy dissipation in bogie suspension systems
- 20 February 2026
- Published by Elsevier in Heavy Rail
- Vol. 1
Open AccessA simplified framework for sensitivity analysis of energy dissipation in bogie suspension systems
- 9 February 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 240 (6) , 744-753
Impact of wheel diameter on the wear and fatigue of heavy-haul railway wheels
Several methods to optimize the center of gravity have been studied. However, less attention has been given to the effect of wheel diameter on dynamic responses. This paper investigates the impact of wheel diameter on the performance of freight wagons, focusing on wear and fatigue analysis under different wheel sizes. Dynamic simulations were conducted, maintaining consistent load mass and bogie type, while varying wheel diameters. Wear was simulated using Archard’s law, and fatigue was analyzed using finite element modeling employing the Dang Van criterion. The findings show that a decrease in wheel radius can lead to up to 56% reduction in Tγ. Wear depth increases by 20% on the tread as flange wear decreases with smaller wheel radii; however, a 27% reduction in tread wear depth occurred in the absence of flange contact, resulting from a more evenly distributed wear pattern due to an expanded transverse wear area. The fatigue index remained negative for all cases, indicating a low probability of Rolling Contact Fatigue. In addition, the fatigue analysis shows a reduction in maximum Dang Van stress, associated with a deeper crack initiation point, as the radius reduces, extending crack initiation life. Reducing the wheel radius extended the crack initiation life by 174.3%, allowing the wheel to travel 2.74 times the distance of the standard baseline wheel before crack initiation.
- 9 February 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 240 (6) , 744-753
Impact of wheel diameter on the wear and fatigue of heavy-haul railway wheels
Several methods to optimize the center of gravity have been studied. However, less attention has been given to the effect of wheel diameter on dynamic responses. This paper investigates the impact of wheel diameter on the performance of freight wagons, focusing on wear and fatigue analysis under different wheel sizes. Dynamic simulations were conducted, maintaining consistent load mass and bogie type, while varying wheel diameters. Wear was simulated using Archard’s law, and fatigue was analyzed using finite element modeling employing the Dang Van criterion. The findings show that a decrease in wheel radius can lead to up to 56% reduction in Tγ. Wear depth increases by 20% on the tread as flange wear decreases with smaller wheel radii; however, a 27% reduction in tread wear depth occurred in the absence of flange contact, resulting from a more evenly distributed wear pattern due to an expanded transverse wear area. The fatigue index remained negative for all cases, indicating a low probability of Rolling Contact Fatigue. In addition, the fatigue analysis shows a reduction in maximum Dang Van stress, associated with a deeper crack initiation point, as the radius reduces, extending crack initiation life. Reducing the wheel radius extended the crack initiation life by 174.3%, allowing the wheel to travel 2.74 times the distance of the standard baseline wheel before crack initiation.
- Open Access
- 1 October 2025
- Published by Universidade Federal do Espirito Santo in Brazilian Journal of Production Engineering
- Vol. 11 (4) , 359-369
Investigação experimental de revestimentos refletores solares como isolantes térmicos para trilhos em corredores de transporte de cargas pesadas
Os trilhos são componentes críticos da infraestrutura ferroviária responsáveis por distribuir cargas, guiar veículos e garantir segurança operacional. No entanto, variações de temperatura e irradiação solar induzem estresse térmico, levando à expansão e contração dos trilhos, bem como ao potencial de flambagem. Embora estudos anteriores tenham explorado a otimização do perfil e lubrificação, há pouca pesquisa sobre mitigação térmica via revestimentos. Este estudo avalia a eficácia de três revestimentos comerciais na redução da variação de temperatura em trilhos AREMA 136RE. Termopares monitoraram as temperaturas em amostras revestidas e não revestida ao longo de várias estações, enquanto um piranômetro registrava a irradiação solar. Os resultados mostram que os trilhos revestidos tiveram picos de temperatura significativamente menores, com reduções superiores a 10°C no verão. Revestimentos com nanoesferas cerâmicas ocas tiveram desempenho superior. Eles mantiveram temperaturas 8–10% menores que a resina alquídica acima de 20 °C. A análise sazonal confirmou comportamento consistente, com diferenciais diminuindo nos meses frios. Os resultados sugerem que revestimentos refletivos podem mitigar riscos de flambagem térmica, principalmente em curvas acentuadas (raio < 50 m), onde os diferenciais de temperatura críticos são inferiores a 20 °C.
- 1 October 2025
- Published by Universidade Federal do Espirito Santo in Brazilian Journal of Production Engineering
- Vol. 11 (4) , 359-369
Open AccessInvestigação experimental de revestimentos refletores solares como isolantes térmicos para trilhos em corredores de transporte de cargas pesadas
Os trilhos são componentes críticos da infraestrutura ferroviária responsáveis por distribuir cargas, guiar veículos e garantir segurança operacional. No entanto, variações de temperatura e irradiação solar induzem estresse térmico, levando à expansão e contração dos trilhos, bem como ao potencial de flambagem. Embora estudos anteriores tenham explorado a otimização do perfil e lubrificação, há pouca pesquisa sobre mitigação térmica via revestimentos. Este estudo avalia a eficácia de três revestimentos comerciais na redução da variação de temperatura em trilhos AREMA 136RE. Termopares monitoraram as temperaturas em amostras revestidas e não revestida ao longo de várias estações, enquanto um piranômetro registrava a irradiação solar. Os resultados mostram que os trilhos revestidos tiveram picos de temperatura significativamente menores, com reduções superiores a 10°C no verão. Revestimentos com nanoesferas cerâmicas ocas tiveram desempenho superior. Eles mantiveram temperaturas 8–10% menores que a resina alquídica acima de 20 °C. A análise sazonal confirmou comportamento consistente, com diferenciais diminuindo nos meses frios. Os resultados sugerem que revestimentos refletivos podem mitigar riscos de flambagem térmica, principalmente em curvas acentuadas (raio < 50 m), onde os diferenciais de temperatura críticos são inferiores a 20 °C.
- 14 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 239 (5) , 431-442
Algorithm-based strategy to define an equivalent railway track for wear simulations
Multibody simulations of train dynamics commonly employ generic short tracks to validate and observe the behaviour of wagons in certain conditions. However, for proper wheel wear analysis, the entire railway track should be modelled, increasing computational cost and time to obtain worn profiles and wear parameters. The major novelty of this work is the description of a reproducible algorithm-based methodology to obtain a statistically representative shorter equivalent railway track for wear simulations. The proposed methodology includes combining a real measured track with multibody dynamic simulation. To verify the approach, a case study was conducted on a 505 km-long railway in Brazil. Additionally, two distinct vehicles were employed: a European wagon with a standard gauge and a Brazilian wagon with a meter gauge. The shorter equivalent tracks were compared in terms of worn area and wear depth to the initial track, and the generated tracks were cross-compared between vehicles to verify the robustness of the method. It is observed that wear simulations can be performed more efficiently and effectively, reducing the computational time by at least 94%, while still obtaining accurate results, given that the final equivalent tracks were 18.59 times shorter for the Brazilian model and 22.45 times shorter for the European model comparing to the real track, with the maximum deviation being 6.55% in flange depth and with a maximum root mean-square error (RMSE) of 871 nm.
- 14 February 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part F: Journal of Rail and Rapid Transit
- Vol. 239 (5) , 431-442
Algorithm-based strategy to define an equivalent railway track for wear simulations
Multibody simulations of train dynamics commonly employ generic short tracks to validate and observe the behaviour of wagons in certain conditions. However, for proper wheel wear analysis, the entire railway track should be modelled, increasing computational cost and time to obtain worn profiles and wear parameters. The major novelty of this work is the description of a reproducible algorithm-based methodology to obtain a statistically representative shorter equivalent railway track for wear simulations. The proposed methodology includes combining a real measured track with multibody dynamic simulation. To verify the approach, a case study was conducted on a 505 km-long railway in Brazil. Additionally, two distinct vehicles were employed: a European wagon with a standard gauge and a Brazilian wagon with a meter gauge. The shorter equivalent tracks were compared in terms of worn area and wear depth to the initial track, and the generated tracks were cross-compared between vehicles to verify the robustness of the method. It is observed that wear simulations can be performed more efficiently and effectively, reducing the computational time by at least 94%, while still obtaining accurate results, given that the final equivalent tracks were 18.59 times shorter for the Brazilian model and 22.45 times shorter for the European model comparing to the real track, with the maximum deviation being 6.55% in flange depth and with a maximum root mean-square error (RMSE) of 871 nm.
- Open Access
- 9 April 2024
- Published by Springer Nature in Railway Engineering Science
- Vol. 32 (3) , 307-323
The effectiveness of different wear indicators in quantifying wear on railway wheels of freight wagons
Railway infrastructure relies on the dynamic interaction between wheels and rails; thus, assessing wheel wear is a critical aspect of maintenance and safety. This paper focuses on the wheel–rail wear indicator T-gamma (Tγ). Amidst its use, it becomes apparent that Tγ, while valuable, fails to provide a comprehensive reflection of the actual material removal and actual contact format, which means that using only Tγ as a target for optimization of profiles is not ideal. In this work, three different freight wagons are evaluated: a meter-gauge and a broad-gauge heavy haul vehicles from South American railways, and a standard-gauge freight vehicle operated in Europe, with different axle loads and dissimilar new wheel/rail profiles. These vehicles are subjected to comprehensive multibody simulations on various tracks. The simulations aimed to elucidate the intricate relationship between different wear indicators: Tγ, wear index, material removal, and maximum wear depth, under diverse curves, non-compensated lateral accelerations (Anc), and speeds. Some findings showed a correlation of 0.96 between Tγ and wear depth and 0.82 between wear index and material removed for the outer wheel. From the results, the Tγ is better than the wear index to be used when analyzing wear depth while the wear index is more suited to foresee the material lost. The results also show the low influence of Anc on wear index and Tγ. By considering these factors together, the study aims to improve the understanding of wheel–rail wear by selecting the best wear analysis approaches based on the effectiveness of each parameter.
- 9 April 2024
- Published by Springer Nature in Railway Engineering Science
- Vol. 32 (3) , 307-323
Open AccessThe effectiveness of different wear indicators in quantifying wear on railway wheels of freight wagons
Railway infrastructure relies on the dynamic interaction between wheels and rails; thus, assessing wheel wear is a critical aspect of maintenance and safety. This paper focuses on the wheel–rail wear indicator T-gamma (Tγ). Amidst its use, it becomes apparent that Tγ, while valuable, fails to provide a comprehensive reflection of the actual material removal and actual contact format, which means that using only Tγ as a target for optimization of profiles is not ideal. In this work, three different freight wagons are evaluated: a meter-gauge and a broad-gauge heavy haul vehicles from South American railways, and a standard-gauge freight vehicle operated in Europe, with different axle loads and dissimilar new wheel/rail profiles. These vehicles are subjected to comprehensive multibody simulations on various tracks. The simulations aimed to elucidate the intricate relationship between different wear indicators: Tγ, wear index, material removal, and maximum wear depth, under diverse curves, non-compensated lateral accelerations (Anc), and speeds. Some findings showed a correlation of 0.96 between Tγ and wear depth and 0.82 between wear index and material removed for the outer wheel. From the results, the Tγ is better than the wear index to be used when analyzing wear depth while the wear index is more suited to foresee the material lost. The results also show the low influence of Anc on wear index and Tγ. By considering these factors together, the study aims to improve the understanding of wheel–rail wear by selecting the best wear analysis approaches based on the effectiveness of each parameter.
- 8 April 2024
- Published by Springer Nature in Multibody System Dynamics
- Vol. 63 (1-2) , 63-81
Comparison between quasi-static and multibody dynamic simulations for wheel-rail contact analysis
- 8 April 2024
- Published by Springer Nature in Multibody System Dynamics
- Vol. 63 (1-2) , 63-81
Comparison between quasi-static and multibody dynamic simulations for wheel-rail contact analysis
- Open Access
- 6 January 2021
- Published by Springer Nature in SN Applied Sciences
- Vol. 3 (1) , 1-13
Tool wear analysis in milling of locomotives wheels
The present work aims to evaluate the tool wear during the milling process of locomotives wheels—class C. A digital microscope is used to identify both the wear and the damage. The wear or damage, when propagated, can compromise the wheel roughness, which has a significant economic importance to railroad maintenance. A system for image capture composed of an ISM-PM200S INSIZE Digital Microscope and the ISM-Pro software is used to measure the flank wear. Firstly, milling process is applied with different numbers of passes. The results showed that, after flank wear, the most common wear is the thermal crack. It is also possible to observe the appearance of chipping and fracture as a consequence of the combination of thermal and mechanical cracks in the same insert. The inserts are more damaged in the raceway, due to the hardening of this region during its use. Inserts in the frieze region also showed higher values of wear, justified by the conditions of the railway. The highest values observed are around 0.1 mm. It is possible to notice that some inserts showed other damages, such as breaks and chipping, even before reaching the end of life due to wear.
- 6 January 2021
- Published by Springer Nature in SN Applied Sciences
- Vol. 3 (1) , 1-13
Open AccessTool wear analysis in milling of locomotives wheels
The present work aims to evaluate the tool wear during the milling process of locomotives wheels—class C. A digital microscope is used to identify both the wear and the damage. The wear or damage, when propagated, can compromise the wheel roughness, which has a significant economic importance to railroad maintenance. A system for image capture composed of an ISM-PM200S INSIZE Digital Microscope and the ISM-Pro software is used to measure the flank wear. Firstly, milling process is applied with different numbers of passes. The results showed that, after flank wear, the most common wear is the thermal crack. It is also possible to observe the appearance of chipping and fracture as a consequence of the combination of thermal and mechanical cracks in the same insert. The inserts are more damaged in the raceway, due to the hardening of this region during its use. Inserts in the frieze region also showed higher values of wear, justified by the conditions of the railway. The highest values observed are around 0.1 mm. It is possible to notice that some inserts showed other damages, such as breaks and chipping, even before reaching the end of life due to wear.