Serhat Çelikten
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Serhat Çelikten has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- İsmail İsa Atabey
Nevşehir Hacı Bektaş Veli University, Department of Civil Engineering, Nevşehir, Türkiye
9 shared publications - Mehmet Canbaz
Department of Civil Engineering, Eskisehir Osmangazi University, 26040 Eskisehir, Türkiye
7 shared publications Mustafa Sarıdemir
7 shared publications- Bilal Baran
NEVŞEHİR HACI BEKTAŞ VELİ ÜNİVERSİTES
3 shared publications - Zahide Bayer Ozturk
Nevşehir Haci Bektaş Veli University
3 shared publications - Burak Işıkdağ
Department of Construction, Porsuk Vocational School, Eskişehir Technical University, Eskişehir 26140, Turkey
2 shared publications
Latest Publications
- 4 February 2026
- Published by Elsevier in Environmental Research
- Vol. 295, 123914
Life-cycle assessment and microstructural performance of andesite dust–modified alkali-activated hybrid mortars at ambient curing conditions
- 4 February 2026
- Published by Elsevier in Environmental Research
- Vol. 295, 123914
Life-cycle assessment and microstructural performance of andesite dust–modified alkali-activated hybrid mortars at ambient curing conditions
- 10 September 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 113
The effect of basalt stone cutting waste on the high-temperature performance of fly ash-based geopolymers
- 10 September 2025
- Published by Elsevier in Journal of Building Engineering
- Vol. 113
The effect of basalt stone cutting waste on the high-temperature performance of fly ash-based geopolymers
- Open Access
- 25 March 2025
- Published by Elsevier in Cleaner Waste Systems
- Vol. 11
Green optimization of vapour-cured geopolymer mortars: Predicting cost, mechanical properties, and environmental impact with artificial neural networks
- 25 March 2025
- Published by Elsevier in Cleaner Waste Systems
- Vol. 11
Open AccessGreen optimization of vapour-cured geopolymer mortars: Predicting cost, mechanical properties, and environmental impact with artificial neural networks
- 16 January 2025
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 32 (7) , 3629-3648
Mechanical and microstructural properties of fiber-reinforced basalt rock cutting waste-based geopolymer composites exposed to high temperatures
Managing basalt rock cutting waste in an environmentally responsible manner is crucial to mitigate its negative impacts and protect both the environment and human health. Recycling basalt rock cutting waste in geopolymer applications offers multiple environmental, economic, and performance benefits, making it a promising approach for sustainable construction practices. For this purpose, this study concerns about the performance of fiber-reinforced basalt rock-cutting waste-based geopolymer composites at high temperatures up to 1000 °C. Geopolymer composites were manufactured by activating basalt rock cutting waste with sodium silicate. Alongside the fiber-free mixtures, fiber-reinforced geopolymer composites incorporating 0.5% and 1.0% basalt or polypropylene fibers by volume were synthesized. These composites underwent thermal curing at 100 °C for two distinct durations: 8 h and 24 h. In addition, the geopolymer composites were subjected to thermal exposure at three different temperatures: 600 °C, 800 °C, and 1000 °C. Changes in the strength and weights of the composites were determined after high-temperature exposure. In addition, XRD and SEM/EDX analyses were performed on the selected composites to investigate the changes in the microstructure of the composites. Thermal curing time and fiber content had significant influence on the high-temperature performance of the geopolymer composites. In this study, geopolymer mortars based on basalt rock cutting waste were successfully developed, demonstrating resistance to elevated temperatures up to 1000 °C. No reduction in compressive strength was observed in any of the composites when exposed to 600 °C, 800 °C, and 1000 °C. In fact, an increase in strength was recorded at varying rates, compared to the pre-exposure values.
- 16 January 2025
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 32 (7) , 3629-3648
Mechanical and microstructural properties of fiber-reinforced basalt rock cutting waste-based geopolymer composites exposed to high temperatures
Managing basalt rock cutting waste in an environmentally responsible manner is crucial to mitigate its negative impacts and protect both the environment and human health. Recycling basalt rock cutting waste in geopolymer applications offers multiple environmental, economic, and performance benefits, making it a promising approach for sustainable construction practices. For this purpose, this study concerns about the performance of fiber-reinforced basalt rock-cutting waste-based geopolymer composites at high temperatures up to 1000 °C. Geopolymer composites were manufactured by activating basalt rock cutting waste with sodium silicate. Alongside the fiber-free mixtures, fiber-reinforced geopolymer composites incorporating 0.5% and 1.0% basalt or polypropylene fibers by volume were synthesized. These composites underwent thermal curing at 100 °C for two distinct durations: 8 h and 24 h. In addition, the geopolymer composites were subjected to thermal exposure at three different temperatures: 600 °C, 800 °C, and 1000 °C. Changes in the strength and weights of the composites were determined after high-temperature exposure. In addition, XRD and SEM/EDX analyses were performed on the selected composites to investigate the changes in the microstructure of the composites. Thermal curing time and fiber content had significant influence on the high-temperature performance of the geopolymer composites. In this study, geopolymer mortars based on basalt rock cutting waste were successfully developed, demonstrating resistance to elevated temperatures up to 1000 °C. No reduction in compressive strength was observed in any of the composites when exposed to 600 °C, 800 °C, and 1000 °C. In fact, an increase in strength was recorded at varying rates, compared to the pre-exposure values.
- 3 December 2024
- Published by Elsevier in Advanced Powder Technology
- Vol. 36 (1)
High-temperature performance of geopolymer mortars containing ceramic filter press cake and pottery waste powders
- 3 December 2024
- Published by Elsevier in Advanced Powder Technology
- Vol. 36 (1)
High-temperature performance of geopolymer mortars containing ceramic filter press cake and pottery waste powders
- Open Access
- 12 August 2024
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 32 (2) , 1326-1334
UÇUCU KÜL VE PERLİT ESASLI GEOPOLİMER HARÇLARDA ÇÖMLEK SIR ATIĞI İKAMESİNİN YÜKSEK SICAKLIK DAYANIKLILIĞI ÜZERİNDEKİ ETKİSİ
Bu çalışmada, perlit (PT) ve uçucu kül (UK) bazlı geopolimerlere çömlek sırı atığı (ÇSA) ikamesinin mekanik özellikler ve yüksek sıcaklık performansı üzerindeki etkisi araştırılmıştır. Sadece PT, sadece UK ve ağırlıkça %75 UK ve %25 PT içeriği ile üretilen geopolimer harçlara %10, 20 ve 30 oranlarında ÇSA ikame edilmiştir. Harçlar, sabit 10M NaOH içeriği ve 8 saat 100 ºC ısıl kür ile üretilmiştir. Üretilen harçların 7, 28 ve 90 günlük eğilme ve basınç dayanımları belirlenmiş ve 500 ºC, 750 ºC ve 1000 ºC sıcaklıklarındaki performansları değerlendirilmiştir. Deneyler sonucunda, ÇSA malzemesinin PT ve UK+PT içeren numunelere kütlece %20 oranına kadar ikame edilmesinin nihai basınç dayanımı açısından olumlu yönde etkileri olduğu, UK içeren numunelerde ise ÇSA ikamesinin nihai basınç dayanımı açısından olumsuz etkileri olduğu tespit edilmiştir. Nihai dayanımlarda en yüksek değerler, 34.4 ve 32.41 MPa basınç ve 6.46 ve 6.3 MPa eğilme dayanımları ile UK+PT+ÇSA içeren numunelerde sırasıyla %10 ve 20 ÇSA oranlarında elde edilmiştir. Eğilme ve basınç dayanımları açısından optimum ÇSA oranının %10-20 aralığında olduğu söylenebilir. UK malzemesine ÇSA malzemesinin ikamesi, kür yaşına göre dayanım gelişimlerini olumsuz etkilerken, PT ve UK+PT içeren numunelere ÇSA malzemesi ikamesi dayanım gelişimlerinde olumlu etkiler meydana getirmiştir. ÇSA malzemesi yüksek sıcaklık performansı açısından tüm gruplarda olumlu etki meydana getirmiştir. ÇSA malzemesinin karışımlarda kütlece ikame yüzdesi arttıkça, dayanım kayıpları azalmıştır. UK malzemesinin yerine %30 ÇSA malzemesinin ikame edildiği numunelerde 750 ºC’de %40’a varan dayanım artışı tespit edilmiştir.
- 12 August 2024
- Published by Eskisehir Osmangazi Universitesi Muhendislik ve Mimarlik Fakultesi Dergisi in Eskişehir Osmangazi Üniversitesi Mühendislik ve Mimarlık Fakültesi Dergisi
- Vol. 32 (2) , 1326-1334
Open AccessUÇUCU KÜL VE PERLİT ESASLI GEOPOLİMER HARÇLARDA ÇÖMLEK SIR ATIĞI İKAMESİNİN YÜKSEK SICAKLIK DAYANIKLILIĞI ÜZERİNDEKİ ETKİSİ
Bu çalışmada, perlit (PT) ve uçucu kül (UK) bazlı geopolimerlere çömlek sırı atığı (ÇSA) ikamesinin mekanik özellikler ve yüksek sıcaklık performansı üzerindeki etkisi araştırılmıştır. Sadece PT, sadece UK ve ağırlıkça %75 UK ve %25 PT içeriği ile üretilen geopolimer harçlara %10, 20 ve 30 oranlarında ÇSA ikame edilmiştir. Harçlar, sabit 10M NaOH içeriği ve 8 saat 100 ºC ısıl kür ile üretilmiştir. Üretilen harçların 7, 28 ve 90 günlük eğilme ve basınç dayanımları belirlenmiş ve 500 ºC, 750 ºC ve 1000 ºC sıcaklıklarındaki performansları değerlendirilmiştir. Deneyler sonucunda, ÇSA malzemesinin PT ve UK+PT içeren numunelere kütlece %20 oranına kadar ikame edilmesinin nihai basınç dayanımı açısından olumlu yönde etkileri olduğu, UK içeren numunelerde ise ÇSA ikamesinin nihai basınç dayanımı açısından olumsuz etkileri olduğu tespit edilmiştir. Nihai dayanımlarda en yüksek değerler, 34.4 ve 32.41 MPa basınç ve 6.46 ve 6.3 MPa eğilme dayanımları ile UK+PT+ÇSA içeren numunelerde sırasıyla %10 ve 20 ÇSA oranlarında elde edilmiştir. Eğilme ve basınç dayanımları açısından optimum ÇSA oranının %10-20 aralığında olduğu söylenebilir. UK malzemesine ÇSA malzemesinin ikamesi, kür yaşına göre dayanım gelişimlerini olumsuz etkilerken, PT ve UK+PT içeren numunelere ÇSA malzemesi ikamesi dayanım gelişimlerinde olumlu etkiler meydana getirmiştir. ÇSA malzemesi yüksek sıcaklık performansı açısından tüm gruplarda olumlu etki meydana getirmiştir. ÇSA malzemesinin karışımlarda kütlece ikame yüzdesi arttıkça, dayanım kayıpları azalmıştır. UK malzemesinin yerine %30 ÇSA malzemesinin ikame edildiği numunelerde 750 ºC’de %40’a varan dayanım artışı tespit edilmiştir.