MCMehmet Canbaz

Mehmet Canbaz

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Mehmet Canbaz has a total of 45 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Valorization of pinus and cedrus acicular leaves as bio-based fibers for reinforced cementitious composites: Extraction, microstructural characterization and mechanical performance

    by Fatih Şamdan, Canan Şamdan, Mehmet Canbaz

    In modern construction applications, various cement-based composite material systems are being developed using forest products and forest waste, such as biobased fibers. These composites serve as sustainable building materials, including wood-cement composites, fiber-reinforced panels, lightweight building elements, and precast building components, especially in non-load-bearing architectural applications. In this study, the physical and mechanical properties of a composite produced in a similar manner, using acicular leaves of Pinus nigra and Cedrus libani as natural fibers, were examined. In this context, the fibers underwent a multi-stage pre-treatment, including hot water extraction, alkaline treatment, and Ca(OH)₂ mineralization, followed by characterization; the treatments were verified by SEM, EDS, and FTIR analyses. Short Cedrus fibers are randomly distributed in the matrix to form an isotropic structure, while long Pinus fibers are oriented perpendicular to the load direction to obtain an orthotropic structure. Unit weight, ultrasonic pulse velocity, dynamic modulus of elasticity, and compressive, flexural, and splitting tensile strengths were determined. When compared, short, isotropic cedar fibers showed higher compressive strength, while long, oriented pine fibers exhibited superior bending and splitting tensile performance.

  • Open Access

    Effectiveness of TiO2 coating on concrete surfaces for photocatalytic degradation of solutions

    by Fatih Şamdan, Canan Şamdan, Emir Günaltılı, Serdal Ünal, Mehmet Canbaz

    In this study, the photocatalytic performance of TiO₂-coated concrete surfaces was systematically investigated with respect to coating configuration and catalyst loading using methylene blue (MB) and Rhodamine B (Rh-B) as model organic pollutants. TiO₂ was applied onto concrete surfaces at different concentrations (5, 10, 15, and 20 wt%) in both single-layer and double-layer configurations, and the degradation behavior of the dyes under UV irradiation was evaluated. The results revealed that increasing TiO₂ content significantly enhanced photocatalytic activity in both coating configurations. However, double-layer coatings consistently outperformed single-layer systems, particularly at higher TiO₂ loadings. The maximum degradation efficiencies reached 52.12% for MB and 77.4% for Rh-B under UV irradiation, demonstrating the effectiveness of TiO₂-coated surfaces in removing organic pollutants. Kinetic analysis indicated that the photocatalytic degradation process followed pseudo-first-order kinetics, with higher apparent rate constants (Kapp) observed in double-layer systems. This enhancement was attributed to increased availability of active sites, improved light utilization, and more efficient charge-carrier dynamics. Mechanistically, the generation of reactive oxygen species (ROS), such as hydroxyl and superoxide radicals, along with improved charge separation facilitated by surface hydroxyl groups and oxygen vacancies, played a key role in enhancing photocatalytic performance. Overall, the findings demonstrate that optimizing both TiO₂ loading and coating architecture provides an effective strategy for improving the photocatalytic efficiency of cement-based materials. The proposed double-layer TiO₂ coating system offers significant potential for developing self-cleaning, environmentally responsive construction materials for urban applications.

  • Open Access

    Bio-based cementitious composites reinforced with natural fibers derived from Cedrus libani A.Rich. acicular leaf: Extraction, microstructural characterization, and mechanical performance after thermal exposure

    by Fatih Şamdan, Canan Şamdan, Mehmet Canbaz

    This study investigates the physical and mechanical performance of bio-based cementitious composites produced with natural fibers obtained from dried, fallen acicular leaf of Cedrus libani A.Rich. The fibers underwent a multi-stage pre-treatment prior to composite production, including hot water extraction, alkaline treatment (NaOH), and Ca(OH)₂ mineralization. Changes in surface morphology and chemical composition were confirmed by SEM and EDS analyses, and significant calcium enrichment and increased roughness were observed on the fiber surface after mineralization. Specimens produced with aggregate- and additive-free mixtures were exposed to temperatures of 20, 200, and 400 °C for 3 hours at the end of the curing periods. Unit volume weight, ultrasonic pulse velocity, compressive, flexural, and splitting tensile strengths were determined, and the dynamic modulus of elasticity was calculated. The results showed that limited losses in mechanical properties occurred up to 200 °C, while more significant reductions in strength and stiffness occurred at 400 °C due to microcrack formation and weakening of the fiber-matrix interface. It was determined that mixtures with a high fiber/cement ratio partially limit crack progression and reduce strength loss in certain temperature ranges. The findings reveal the mechanical properties of Cedrus libani acicular leaf fibers as reinforcement in cementitious composites after thermal exposure.

  • Open Access

    Development of a sustainable geopolymer structural element with waste glass powder: Mechanical characteristics

    by Serdal Ünal, Mehmet Canbaz

    In this study, the potential of converting waste glass powder, sourced from glass manufacturing processes in Turkey, into sustainable and environmentally friendly construction materials was explored. A novel approach was adopted by producing geopolymeric building elements using only waste glass powder, water, and varying concentrations of sodium hydroxide (2%, 4%, and 6%) in a completely cement-free system. This distinguishes the study from previous works, as it focuses solely on waste glass powder as the primary aluminosilicate source without incorporating additional binders such as fly ash or slag. The physical and mechanical properties of the produced samples were evaluated through unit weight, ultrasonic pulse velocity, compressive strength, flexural strength, and tensile strength tests. The results indicated that the mixture containing 4% sodium hydroxide provided optimal performance, demonstrating superior mechanical strength, structural integrity, and durability. Notably, the specimens produced with 4% NaOH exhibited higher durability than aerated concrete and achieved strength and density values close to conventional bricks, suggesting their potential applicability in non-load-bearing structural elements. Furthermore, this study addresses a significant gap in the literature regarding the standalone use of waste glass powder in geopolymer systems and contributes valuable data on its performance in solid form. The findings also highlight the material's potential to reduce reliance on Portland cement, thereby lowering carbon emissions and promoting the circular economy through effective waste utilization. Overall, the study offers an innovative and practical solution for sustainable construction by demonstrating the feasibility of producing high-performance geopolymer elements entirely from waste-derived materials.


  • COMPARATIVE ANALYSIS OF MECHANICAL PROPERTIES OF EPOXY COATED AND UNCOATED REINFORCEMENT BAR

    by Kerem Aybar, Serdal Ünal, Ömer Karagöz, Mehmet Canbaz

    This study aims to enhance the mechanical and bond performance of reinforcing bars embedded in concrete by applying epoxy coatings as a protective layer against external effects. For this purpose, epoxy-coated and uncoated rebars with a diameter of 10 mm and length of 30 cm were embedded into 15×15×15 cm concrete blocks using two different methods: cast-in-place and post-installed with chemical anchoring after curing. Each specimen contained a single rebar, and mechanical tests including yield strength, tensile strength, fracture strength, reduction of area, elongation at break, toughness, modulus of elasticity, and adherence strength were conducted. The results showed that epoxy coating slightly improved mechanical properties such as yield and tensile strength, while enhancing toughness and maintaining sufficient ductility. Although a slight decrease in stiffness and plastic strain capacity was observed, the coating increased the reliability of yield behavior. Most notably, adherence strength was significantly improved by epoxy coating, particularly in post-installed specimens, where an increase of over 30% was recorded. Overall, epoxy coating proved to be an effective solution for improving both mechanical integrity and adhesion performance of reinforcing bars, especially in conditions where chemical durability and long-term performance are critical.

  • Performance of SIMCON in Structural Retrofitting Under Freeze–Thaw Exposure

    by Ömer Karagöz, Serdal Ünal, Kerem Aybar, Mehmet Canbaz

    This study investigates the freeze-thaw (F-T) durability and mechanical performance of Slurry Infiltrated Mat Concrete (SIMCON) produced with two different binders, Portland cement (CEM I 42.5R) and calcium aluminate cement (CAC). SIMCON composites were fabricated by infiltrating cement pastes into randomly oriented steel wool mats, aiming for improved fiber distribution and matrix-reinforcement interaction. Specimens were subjected to 0, 15, and 30 F-T cycles and evaluated on the basis of unit weight, ultrasonic pulse velocity (UPV), flexural strength, and compressive strength. The results showed that all properties deteriorated with increasing number of cycles; however, CAC-based composites consistently outperformed their CEM I counterparts. After 30 cycles, CAC specimens retained 54% higher compressive strength and exhibited slower deterioration rates in UPV and flexural strength. The superior performance of CAC is attributed to its denser, more stable microstructure and its improved resistance to internal cracking and moisture damage. These findings demonstrate that CAC is a promising binder for SIMCON in infrastructure and retrofit applications exposed to harsh environmental conditions where long-term durability is critical.

  • Physical and Mechanical Properties of Different Types of Mortars Produced with Hydrophobic Perlite

    by Serdal Ünal, Hasan Serkan Gökçen, Mehmet Canbaz

    This study contributes to the limited research in this field by enabling hydrophobic perlite to be used more efficiently in cement and gypsum based lightweight composites by reducing water absorption and explores an innovative approach to increase the hydrophobic properties of expanded perlite by making it hydrophobic. In the first stage, hydrophobic perlite was obtained by grinding expanded perlite together with a liquid chemical agent with hydrophobic properties. This hydrophobic perlite was mixed with cement and gypsum at different water ratios to produce various mortars. The physical properties of the mortars were analyzed in terms of unit weight, water absorption rate by weight, capillary water absorption rate and ultrasonic pulse velocity, while the compressive strength was investigated in terms of mechanical properties. Tests on criteria, such as water absorption test, ultrasonic transmission rate, unit weight and compressive strength revealed that mortars produced with hydrophobic perlite exhibited significantly lower water absorption rates and improved mechanical properties compared to conventional mortars. The findings of the study indicate that hydrophobic perlite is an effective contributor to the production of water-resistant and performance-enhanced building materials. This method offers potential applications in the construction and building industries for the development of mortars and other building materials with enhanced hydrophobic properties.


  • Open Access

    Impact of wrap quantity on strength of damaged and undamaged CFRP-reinforced structural members

    by Serdal Ünal, Ahmet Burak Kurt, Mehmet Canbaz

    In this study, the effect of carbon fiber reinforced polymer (CFRP) wrapping on the compressive and bending behavior of damaged reinforced concrete structural elements located in high earthquake risk areas was investigated in detail. The main objective was to evaluate the potential of CFRP wraps as an effective strengthening technique for improving the mechanical performance of concrete members that have already sustained damage. During the experimental phase, concrete specimens in the form of 15×15×15 cm cubes and 10×10×50 cm prisms were prepared using CEM IV 32.5 pozzolanic cement, which is commonly used in structural applications due to its durability and environmental benefits. After subjecting these specimens to controlled damage to simulate real-life structural degradation, they were reinforced using single and double layers of CFRP wrapping. The mechanical performances of these wrapped specimens were then assessed through compressive and bending strength tests. The results demonstrated that CFRP wrapping significantly enhanced the compressive strength of the specimens, with double-layer applications showing the greatest improvements. However, the effect on flexural strength was found to be more limited, indicating that although CFRP is 60.83% effective in resisting compressive loads, its contribution to flexural capacity may require additional considerations. Furthermore, double-layer CFRP wrapping not only improved strength but also increased deformation capacity, indicating enhanced ductility and energy absorption. Despite the relatively high cost of CFRP materials, these findings highlight the technique as a practical and efficient solution for the rehabilitation and strengthening of compression load-bearing members, particularly in regions vulnerable to seismic activity.

  • Open Access

    Utilization of expired cement and aged roof tile powder in the production of sustainable geopolymer: Mechanical and physical properties

    by Serdal Ünal, Mehmet Canbaz

    This study deals with the production of geopolymer mortar in order to promote the recycling of waste materials as sustainable building materials. The use of waste materials such as expired cement and aged roof tiles powders in cementitious systems is of great importance in terms of increasing environmental sustainability and reducing industrial waste. Recycling these materials and using them as alternative binders contributes to more environmentally friendly and economical concrete and mortar production by reducing natural resource consumption. Expired cement and aged roof tile powder were used as binder materials and mortar specimens were produced by activating these materials with alkalis such as NaOH and Na2SiO3 at different ratios. Within the scope of the experimental studies, mechanical and physical properties such as unit weight, ultrasonic pulse velocity, compressive strength and bending strength were investigated in detail. The results showed that the expired cement specimens performed better especially in unit weight, ultrasonic pulse velocity and compressive strength tests, while the roof tile powder had superior properties in terms of bending strength. It was also found that the specimens activated with sodium hydroxide (NaOH) exhibited generally higher strength and performance than those activated with sodium silicate (Na2SiO3). These findings prove that waste materials such as both expired cement and roof tile powder can be valuable alternatives in the construction industry in terms of sustainability and waste management and reveal the potential of using these materials in geopolymer mortar production.