Krongthong Kamonsuangkasem
Krongthong Kamonsuangkasem has a total of 41 co-authors. Here are the top co-authors by number of shared publications:
Apichai Therdthianwong
3 shared publicationsSupaporn Therdthianwong
3 shared publicationsXiaohan Chen
National University of Singapore 4 Engineering Drive 4
3 shared publications- Sibudjing Kawi
Department of Chemical and Biomolecular Engineering, National University of Singapore, 4 Engineering Drive 4, 117585, Singapore
2 shared publications Cahyaning Fajar Kresna Murti
1 shared publication- Chatree Saiyasombat
Synchrotron Light Research Institute (Public Organization), Nakhon Ratchasima 30000, Thailand
1 shared publication
Latest Publications
- 22 October 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (43) , 19990-20002
Periodic Macroporous CuCe Catalyst with Prereduced Active Sites for Preferential CO Oxidation
The regulation of Cu valence states, which stabilizes the strongly adsorbed active sites, is a critical factor in improving the CO-PROX reaction performance. Herein, spherical CuCe catalysts were synthesized via the colloidal template method, with the Cu valence states subsequently regulated by prereduction. Among the prepared catalysts, the sample reduced at 100 °C (CuCe-100) exhibited superior activity, achieving 100% CO conversion at 120 °C and maintaining complete conversion up to 180 °C. As revealed by XRD, XPS, XANES, and EXAFS, the superior activity of CuCe-100 is attributed to its higher Cu+, which facilitates oxygen vacancy cycling and thereby enhances CO adsorption. Furthermore, key intermediate species (COOH–, Cu+–CO) were identified by in situ DRIFTS, and DFT verified that CO adsorption is most favorable on the Cu2O (111) surface. This work clarifies at the atomic level that Cu+ is the key adsorption site for CO, thereby deepening the understanding of CO-PROX and paving the way for designing high-performance catalysts via valence regulation.
- 22 October 2026
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 14 (43) , 19990-20002
Periodic Macroporous CuCe Catalyst with Prereduced Active Sites for Preferential CO Oxidation
The regulation of Cu valence states, which stabilizes the strongly adsorbed active sites, is a critical factor in improving the CO-PROX reaction performance. Herein, spherical CuCe catalysts were synthesized via the colloidal template method, with the Cu valence states subsequently regulated by prereduction. Among the prepared catalysts, the sample reduced at 100 °C (CuCe-100) exhibited superior activity, achieving 100% CO conversion at 120 °C and maintaining complete conversion up to 180 °C. As revealed by XRD, XPS, XANES, and EXAFS, the superior activity of CuCe-100 is attributed to its higher Cu+, which facilitates oxygen vacancy cycling and thereby enhances CO adsorption. Furthermore, key intermediate species (COOH–, Cu+–CO) were identified by in situ DRIFTS, and DFT verified that CO adsorption is most favorable on the Cu2O (111) surface. This work clarifies at the atomic level that Cu+ is the key adsorption site for CO, thereby deepening the understanding of CO-PROX and paving the way for designing high-performance catalysts via valence regulation.
Self‐Supported Cu Electrode as the Cathode for Hybrid Zn‐Air/Cu Batteries Achieving Long‐Term Operation Under Oxygen‐Free Condition
The integration of Zn‐air batteries with Zn‐metal batteries enables the efficient realization of hybrid Zn‐based batteries with synergistic high energy and power density. In this hybrid system, the reduction potential of CuO in the Zn‐Cu battery is lower than the oxygen reduction reaction (ORR), thus allowing CuO to replace the ORR and enable discharging under oxygen‐free conditions. Herein, carbon nanotubes are deposited onto copper foam, followed by one‐step calcination process to fabricate self‐supported electrode CuO x @CNTs/CF for hybrid Zn‐air/Cu batteries. The hybrid Zn‐air/Cu batteries deliver the peak power density of 117.5 mW cm −2 and specific capacity of 792.6 mAh g −1 , with a stable cycling life of 800 h. More importantly, the self‐supported electrode enables stable operation for up to 340 h in oxygen‐free environments. Furthermore, the introduction of NiFe‐based active species to construct hybrid Zn‐air/Cu/Ni batteries boosts the peak power density to an excellent 458.4 mW cm −2 . The hybrid batteries exhibit stable cycling life for 1200 h under oxygen‐rich conditions and 390 h in oxygen‐free environments, respectively. This work provides profound insights into the rational design, development and practical applications of hybrid Zn‐based batteries for future energy storage systems.
Self‐Supported Cu Electrode as the Cathode for Hybrid Zn‐Air/Cu Batteries Achieving Long‐Term Operation Under Oxygen‐Free Condition
The integration of Zn‐air batteries with Zn‐metal batteries enables the efficient realization of hybrid Zn‐based batteries with synergistic high energy and power density. In this hybrid system, the reduction potential of CuO in the Zn‐Cu battery is lower than the oxygen reduction reaction (ORR), thus allowing CuO to replace the ORR and enable discharging under oxygen‐free conditions. Herein, carbon nanotubes are deposited onto copper foam, followed by one‐step calcination process to fabricate self‐supported electrode CuO x @CNTs/CF for hybrid Zn‐air/Cu batteries. The hybrid Zn‐air/Cu batteries deliver the peak power density of 117.5 mW cm −2 and specific capacity of 792.6 mAh g −1 , with a stable cycling life of 800 h. More importantly, the self‐supported electrode enables stable operation for up to 340 h in oxygen‐free environments. Furthermore, the introduction of NiFe‐based active species to construct hybrid Zn‐air/Cu/Ni batteries boosts the peak power density to an excellent 458.4 mW cm −2 . The hybrid batteries exhibit stable cycling life for 1200 h under oxygen‐rich conditions and 390 h in oxygen‐free environments, respectively. This work provides profound insights into the rational design, development and practical applications of hybrid Zn‐based batteries for future energy storage systems.
- 9 September 2026
- Published by Elsevier in Molecular Catalysis
- Vol. 604
Synergistic interaction between cobalt and VOx species enhances CO2-assisted oxidative dehydrogenation of propane over Silicalite-1
- 9 September 2026
- Published by Elsevier in Molecular Catalysis
- Vol. 604
Synergistic interaction between cobalt and VOx species enhances CO2-assisted oxidative dehydrogenation of propane over Silicalite-1
- Open Access
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2580 (1)
The effects of concentration of sodium chloride solution on microstructure and corrosion resistance of AISI-304 austenitic stainless steel
Austenitic stainless steel (AISI) 304 is known to have excellent corrosion resistance under atmospheric conditions. However, corrosion resistance in austenitic stainless steel 304 can decrease in a medium containing chloride ions. In this work, the effects of the concentration of sodium chloride solution on microstructure, crystal phases, elemental composition, and corrosion behavior of AISI 304 were focused on by using a digital light microscope, SEM-EDS, XRD, XRF, and linear sweep voltammetry techniques. Various sodium chloride concentrations were prepared at 1%; 2%; 3.5%; 4%; and 5%. The AISI 304 samples were treated mechanically by polishing on the surface, then comparing it to the unpolished samples. Austenitic and ferrite phases were observed in a cubic structure. Iron (Fe), chromium (Cr), nickel (Ni), manganese (Mn), and carbon (C) were found as the major elements. After the AISI 304 samples were immersed in a chlorinated solution, the corrosion from pitting, intergranular, and rust was observed only on the surfaces of the unpolished samples. However, the changes for the crystal structures and major elemental compositions were insignificant when the concentration of chlorinated solution increased. On the other hand, an increase in the corrosion rate was observed. The lowest corrosion resistance of AISI 304 was found at 5% NaCl. When the NaCl concentration increased, the corrosion rate increased.
- 1 January 2023
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2580 (1)
Open AccessThe effects of concentration of sodium chloride solution on microstructure and corrosion resistance of AISI-304 austenitic stainless steel
Austenitic stainless steel (AISI) 304 is known to have excellent corrosion resistance under atmospheric conditions. However, corrosion resistance in austenitic stainless steel 304 can decrease in a medium containing chloride ions. In this work, the effects of the concentration of sodium chloride solution on microstructure, crystal phases, elemental composition, and corrosion behavior of AISI 304 were focused on by using a digital light microscope, SEM-EDS, XRD, XRF, and linear sweep voltammetry techniques. Various sodium chloride concentrations were prepared at 1%; 2%; 3.5%; 4%; and 5%. The AISI 304 samples were treated mechanically by polishing on the surface, then comparing it to the unpolished samples. Austenitic and ferrite phases were observed in a cubic structure. Iron (Fe), chromium (Cr), nickel (Ni), manganese (Mn), and carbon (C) were found as the major elements. After the AISI 304 samples were immersed in a chlorinated solution, the corrosion from pitting, intergranular, and rust was observed only on the surfaces of the unpolished samples. However, the changes for the crystal structures and major elemental compositions were insignificant when the concentration of chlorinated solution increased. On the other hand, an increase in the corrosion rate was observed. The lowest corrosion resistance of AISI 304 was found at 5% NaCl. When the NaCl concentration increased, the corrosion rate increased.
- 29 April 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1101, 318-321
Steam Reforming of Glycerol for Hydrogen Production over Ni Catalysts Supported by CeO2-Al2O3 Xerogel
The Ni catalysts supported by CeO2-Al2O3 xerogel were prepared by sol-gel method. The effect of hydrolysis ratio (R at 16.5 and 165) on CeO2-Al2O3 textural properties and phase formation were investigated. The results revealed that the porous texture and the Ni crystalline phase can be controlled by adjusting the hydrolysis ratio. A high surface area and small Ni crystallite size were obtained by using the hydrolysis ratio of 16.5. For hydrogen production via glycerol steam reforming, the Ni catalyst supported on CeO2-Al2O3 xerogel showed a better catalytic performance than that supported on commercial alumina. The promoted Ni catalyst supported on commercial alumina suddenly deactivated after first 12 h, whereas that on Al2O3 xerogel performed the catalytic stability more than 20 h. This demonstrated that the catalyst prepared by sol-gel method is an interesting catalyst for using in the glycerol steam reforming because of the catalytic stability enhancement.
- 29 April 2015
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 1101, 318-321
Steam Reforming of Glycerol for Hydrogen Production over Ni Catalysts Supported by CeO2-Al2O3 Xerogel
The Ni catalysts supported by CeO2-Al2O3 xerogel were prepared by sol-gel method. The effect of hydrolysis ratio (R at 16.5 and 165) on CeO2-Al2O3 textural properties and phase formation were investigated. The results revealed that the porous texture and the Ni crystalline phase can be controlled by adjusting the hydrolysis ratio. A high surface area and small Ni crystallite size were obtained by using the hydrolysis ratio of 16.5. For hydrogen production via glycerol steam reforming, the Ni catalyst supported on CeO2-Al2O3 xerogel showed a better catalytic performance than that supported on commercial alumina. The promoted Ni catalyst supported on commercial alumina suddenly deactivated after first 12 h, whereas that on Al2O3 xerogel performed the catalytic stability more than 20 h. This demonstrated that the catalyst prepared by sol-gel method is an interesting catalyst for using in the glycerol steam reforming because of the catalytic stability enhancement.
- Open Access
- 1 February 2013
- Published by Elsevier in Fuel Processing Technology
- Vol. 106, 695-703
Hydrogen production from yellow glycerol via catalytic oxidative steam reforming
- 1 February 2013
- Published by Elsevier in Fuel Processing Technology
- Vol. 106, 695-703
Open AccessHydrogen production from yellow glycerol via catalytic oxidative steam reforming