Krzysztof Komeza
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Krzysztof Komeza has a total of 86 co-authors. Here are the top co-authors by number of shared publications:
- Maria Dems
Institute of Mechatronics and Information Systems, Lodz University of Technology Poland, 90-924 Lodz, Poland
32 shared publications - Slawomir Wiak
Lodz University of Technology
14 shared publications - Ewa Napieralska-Juszczak
Univ. Artois, ER4025, LSEE, Béthune, France
10 shared publications - Piotr Napieralski
Lodz University of Technology
9 shared publications - Marcin Lefik
Institute of Mechatronics and Information Systems, Technical University of Lodz, Lodz, Poland
8 shared publications - Daniel Roger
Univ. Artois, UR 4025, Laboratoire Systèmes Électrotechniques et Environnement (LSEE)
7 shared publications
Latest Publications
- Open Access
Refinement of the Parameters of an Induction Motor by Changing the Design from an Internal Rotor to an External Rotor
To varying degrees, optimization is a widely accepted procedure in the design of electrical machines, especially induction machines. This is associated with stringent requirements stemming from international regulations. The use of induction machines in new solutions, including low-speed vehicle drives, introduces challenges because they require high electromagnetic torque at low speeds. These requirements, including dimensional constraints, mean that despite sophisticated optimization, the classic design does not achieve the desired results. In such a case, a general redesign of the motor is necessary, replacing the classic internal rotor motor with an external rotor motor. This paper presents an example of such a design change as part of the parameter refinement process for two selected high-power, high-pole induction motors. Both the FEM method and a suitably adapted analytical method were used to investigate the impact of the design change. This enabled verification of the analytical method’s accuracy and rapid modeling of phenomena and parameters in external rotor motors. The proposed approach can be used to design novel structures and select motor controls for various applications.
Open AccessRefinement of the Parameters of an Induction Motor by Changing the Design from an Internal Rotor to an External Rotor
To varying degrees, optimization is a widely accepted procedure in the design of electrical machines, especially induction machines. This is associated with stringent requirements stemming from international regulations. The use of induction machines in new solutions, including low-speed vehicle drives, introduces challenges because they require high electromagnetic torque at low speeds. These requirements, including dimensional constraints, mean that despite sophisticated optimization, the classic design does not achieve the desired results. In such a case, a general redesign of the motor is necessary, replacing the classic internal rotor motor with an external rotor motor. This paper presents an example of such a design change as part of the parameter refinement process for two selected high-power, high-pole induction motors. Both the FEM method and a suitably adapted analytical method were used to investigate the impact of the design change. This enabled verification of the analytical method’s accuracy and rapid modeling of phenomena and parameters in external rotor motors. The proposed approach can be used to design novel structures and select motor controls for various applications.
- Open Access
Optimization of Induction Motor Control to Limit the Maximum Current and Torque During Voltage Start-Up Using FEM and Analytical Simulation
The paper presents an optimal control strategy selection for an induction motor during voltage start-up, focusing on limiting the maximum current and starting torque surges at a given start-up time. Optimizing the operation of a soft-start system can be achieved using a simple system that assumes a linear voltage increase from a specific initial value. The advantage of this approach is the elimination of transducer systems for measuring voltages and currents. That approach requires simulating the drive system to select the optimal variant for a given system based on maximum and minimum torque values, maximum current, and optimal starting time. Transient calculations, for example, for the induction motor, were performed using both the analytical and circuit-field methods for different U/f time characteristics under varying motor load conditions, and the simulation results were compared with measurements.
Open AccessOptimization of Induction Motor Control to Limit the Maximum Current and Torque During Voltage Start-Up Using FEM and Analytical Simulation
The paper presents an optimal control strategy selection for an induction motor during voltage start-up, focusing on limiting the maximum current and starting torque surges at a given start-up time. Optimizing the operation of a soft-start system can be achieved using a simple system that assumes a linear voltage increase from a specific initial value. The advantage of this approach is the elimination of transducer systems for measuring voltages and currents. That approach requires simulating the drive system to select the optimal variant for a given system based on maximum and minimum torque values, maximum current, and optimal starting time. Transient calculations, for example, for the induction motor, were performed using both the analytical and circuit-field methods for different U/f time characteristics under varying motor load conditions, and the simulation results were compared with measurements.
- Open Access
Practical Verification of the Approximation Method of the Influence of Guillotine and Laser Cutting and Core Dimensions on Losses and Magnetization of Induction Motor Cores
Induction motors are a significant consumer of electricity. One of the crucial elements of losses in an induction motor is core losses. Core losses become dominant in motors powered by an inverter at higher frequencies. The core sheet loss depends on cutting the core using a die or laser. The article presents a practical method for approximating loss characteristics, enabling the determination of losses with high accuracy and the approximation of the magnetization characteristic. The method’s accuracy was verified using sheet metal samples cut with both a guillotine and a laser. The method is an area method; therefore, it is well-suited for use in analytical methods and calculations of power losses based on FEM (Finite Element Method) post-processing. Then, the developed approximations were used to calculate losses in sample induction motors of different powers. The results indicate that the developed method is accurate, making it a viable alternative to the approximate correction factor.
Open AccessPractical Verification of the Approximation Method of the Influence of Guillotine and Laser Cutting and Core Dimensions on Losses and Magnetization of Induction Motor Cores
Induction motors are a significant consumer of electricity. One of the crucial elements of losses in an induction motor is core losses. Core losses become dominant in motors powered by an inverter at higher frequencies. The core sheet loss depends on cutting the core using a die or laser. The article presents a practical method for approximating loss characteristics, enabling the determination of losses with high accuracy and the approximation of the magnetization characteristic. The method’s accuracy was verified using sheet metal samples cut with both a guillotine and a laser. The method is an area method; therefore, it is well-suited for use in analytical methods and calculations of power losses based on FEM (Finite Element Method) post-processing. Then, the developed approximations were used to calculate losses in sample induction motors of different powers. The results indicate that the developed method is accurate, making it a viable alternative to the approximate correction factor.
- 1 September 2024
- Published by SAGE Publications in International Journal of Applied Electromagnetics and Mechanics
- Vol. 76 (1-2) , 121-133
Design of coils for high-power medium-frequency transformers using Grain-Oriented hot cores
This article proposes a design of windings for medium-frequency transformers (MFTs) at the heart of high-power Solid-State Transformers (SSTs). With aluminum interleaved foils of the correct thicknesses, it is possible to obtain low winding losses and a very low leakage inductance well adapted to high-power SSTs able to operate in the medium-voltage grid (5–20 kV). The MFT equivalent resistance and leakage inductance are determined using an analytical model based on Dowell’s hypotheses. Several interleaved winding configurations are analyzed and compared to the standard structure made of two concentric foil coils. The experimental validation is made with short-circuit tests of an MFT fed by a low-level square voltage source at several kHz, which can provide the necessary high current.
- 1 September 2024
- Published by SAGE Publications in International Journal of Applied Electromagnetics and Mechanics
- Vol. 76 (1-2) , 121-133
Design of coils for high-power medium-frequency transformers using Grain-Oriented hot cores
This article proposes a design of windings for medium-frequency transformers (MFTs) at the heart of high-power Solid-State Transformers (SSTs). With aluminum interleaved foils of the correct thicknesses, it is possible to obtain low winding losses and a very low leakage inductance well adapted to high-power SSTs able to operate in the medium-voltage grid (5–20 kV). The MFT equivalent resistance and leakage inductance are determined using an analytical model based on Dowell’s hypotheses. Several interleaved winding configurations are analyzed and compared to the standard structure made of two concentric foil coils. The experimental validation is made with short-circuit tests of an MFT fed by a low-level square voltage source at several kHz, which can provide the necessary high current.
- Open Access
- 14 July 2024
- Published by MDPI AG in Electronics
- Vol. 13 (14) , 2766
Methods for Determining Losses and Parameters of Cylindrical-Rotor Medium-Power Synchronous Generators
This paper presents the analytical and numerical application of a method to determine the parameters and power losses in the core of two medium-power synchronous generators. These generators are used as emergency power sources powered by diesel engines, gas engines, and gas turbines. They cover peak electricity demand but can also be used in traction drives. This article presents a new numerical method for determining losses in the generator core based on the use of a time-stepping solution using the FEM method and calculating these losses using analytical formulas. In calculating the losses for the FEM method, approximations of the loss characteristics of the sheet were used with a wide range of induction values and frequencies. This method is specific to the solution used and was adapted from the authors’ previous work on losses in induction machines. A one-phase winding with alternating voltage was supplied to determine the basic parameters in the form of synchronous reactance. Also, an important novelty is the introduction of a new method of determining the saturation state of the magnetic circuit, which significantly affects the machine parameters. The obtained results were used in analytical calculations and implemented in a computer program that allows for the calculation of electromagnetic parameters, operating characteristics, and core losses, taking into account additional losses, total losses, and efficiency, as well as machine parameters in unsteady operating states and the current characteristics of a three-phase symmetrical short circuit at the machine terminals. The calculations obtained were verified experimentally by measurements of real machines.
- 14 July 2024
- Published by MDPI AG in Electronics
- Vol. 13 (14) , 2766
Open AccessMethods for Determining Losses and Parameters of Cylindrical-Rotor Medium-Power Synchronous Generators
This paper presents the analytical and numerical application of a method to determine the parameters and power losses in the core of two medium-power synchronous generators. These generators are used as emergency power sources powered by diesel engines, gas engines, and gas turbines. They cover peak electricity demand but can also be used in traction drives. This article presents a new numerical method for determining losses in the generator core based on the use of a time-stepping solution using the FEM method and calculating these losses using analytical formulas. In calculating the losses for the FEM method, approximations of the loss characteristics of the sheet were used with a wide range of induction values and frequencies. This method is specific to the solution used and was adapted from the authors’ previous work on losses in induction machines. A one-phase winding with alternating voltage was supplied to determine the basic parameters in the form of synchronous reactance. Also, an important novelty is the introduction of a new method of determining the saturation state of the magnetic circuit, which significantly affects the machine parameters. The obtained results were used in analytical calculations and implemented in a computer program that allows for the calculation of electromagnetic parameters, operating characteristics, and core losses, taking into account additional losses, total losses, and efficiency, as well as machine parameters in unsteady operating states and the current characteristics of a three-phase symmetrical short circuit at the machine terminals. The calculations obtained were verified experimentally by measurements of real machines.
- Open Access
- 27 December 2023
- Published by MDPI AG in Electronics
- Vol. 13 (1) , 119
Influence of the Cast Iron Frame on the Distribution of the Magnetic Field in the Stator Yoke and Additional Power Losses in the Induction Motor
Induction motors are a significant consumer of electricity. Therefore, their energy efficiency level plays a vital role in the world’s energy balance. The world’s markets strive to produce motors of efficiency class IE3 or IE4 while maximizing the use of wire and magnetic materials. However, high induction values in the motor core can also lead to significant losses in construction materials, especially in the magnetic motor housing. This article aimed to show how it is possible to determine the distribution of the magnetic field and additional losses in the yoke and the cast-iron motor frame using field-circuit methods to model the motor and to refine the analytical method for calculating these losses at the motor design stage.
- 27 December 2023
- Published by MDPI AG in Electronics
- Vol. 13 (1) , 119
Open AccessInfluence of the Cast Iron Frame on the Distribution of the Magnetic Field in the Stator Yoke and Additional Power Losses in the Induction Motor
Induction motors are a significant consumer of electricity. Therefore, their energy efficiency level plays a vital role in the world’s energy balance. The world’s markets strive to produce motors of efficiency class IE3 or IE4 while maximizing the use of wire and magnetic materials. However, high induction values in the motor core can also lead to significant losses in construction materials, especially in the magnetic motor housing. This article aimed to show how it is possible to determine the distribution of the magnetic field and additional losses in the yoke and the cast-iron motor frame using field-circuit methods to model the motor and to refine the analytical method for calculating these losses at the motor design stage.
- 2 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (5) , 6532-6542
Solid-State Transformers of Smart High-Power Battery Charger for Electric Vehicles
There is no doubt that society will not turn back: most thermal vehicles will switch to electric ones, not only for cars but also for bigger vehicles. Fast chargers will become more and more essential parts of the global system, they will provide a charge control of batteries and galvanic insulation from the grid. At the present times, compact realizations are based on Solid-State Transformers (SSTs) operating at high frequencies with their well-known advantages and disadvantages, including power limits and reasonably high costs. The authors propose a medium-frequency transformer (MFT) structure using Grain Oriented Electrical Steel (GOES) wound cores and aluminum foil windings. Thanks to this solution, the cost of the device can be reduced. GOES has losses that increase with frequency but decrease with temperature; therefore, the authors propose a transformer structure allowing a hot core inside coils at usual temperatures. This idea is applied to a 400-kW compact battery charger connected to a DC smart grid.
- 2 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 59 (5) , 6532-6542
Solid-State Transformers of Smart High-Power Battery Charger for Electric Vehicles
There is no doubt that society will not turn back: most thermal vehicles will switch to electric ones, not only for cars but also for bigger vehicles. Fast chargers will become more and more essential parts of the global system, they will provide a charge control of batteries and galvanic insulation from the grid. At the present times, compact realizations are based on Solid-State Transformers (SSTs) operating at high frequencies with their well-known advantages and disadvantages, including power limits and reasonably high costs. The authors propose a medium-frequency transformer (MFT) structure using Grain Oriented Electrical Steel (GOES) wound cores and aluminum foil windings. Thanks to this solution, the cost of the device can be reduced. GOES has losses that increase with frequency but decrease with temperature; therefore, the authors propose a transformer structure allowing a hot core inside coils at usual temperatures. This idea is applied to a 400-kW compact battery charger connected to a DC smart grid.
- Open Access
The Influence of Cutting Technology on Magnetic Properties of Non-Oriented Electrical Steel—Review State of the Art
The global drive to reduce energy consumption poses new challenges for designers of electrical machines. Losses in the core are a significant part of losses, especially for machines operating at an increased rotational speed powered by PWM inverters. One of the important problems when calculating core losses is considering the effect of material degradation due to mechanical or laser cutting. To this aim, this paper analyzes and summarizes the knowledge about the sources of material property deterioration and ways of describing this phenomenon. The cited results of material tests indicate the lack of unequivocal relationships allowing us to estimate the degree of material damage and the resulting deterioration of material properties. The main task of this article is to present the state of knowledge on the possibility of taking into account the impact of cutting the core sheets of electric motors on core losses and their impact on the efficiency of the machine. This is a significant problem due to the need to design and manufacture energy-saving electric motors powered with a voltage of 20 to 350 Hz, whose magnetic cores are made of laminates. However, the performed analysis indicates the most important parameters of the cutting process, affecting the degree of material structure destruction. The method of the solution proposed by the authors for core punching and laser cutting, illustrated with a practical example, is also presented.
Open AccessThe Influence of Cutting Technology on Magnetic Properties of Non-Oriented Electrical Steel—Review State of the Art
The global drive to reduce energy consumption poses new challenges for designers of electrical machines. Losses in the core are a significant part of losses, especially for machines operating at an increased rotational speed powered by PWM inverters. One of the important problems when calculating core losses is considering the effect of material degradation due to mechanical or laser cutting. To this aim, this paper analyzes and summarizes the knowledge about the sources of material property deterioration and ways of describing this phenomenon. The cited results of material tests indicate the lack of unequivocal relationships allowing us to estimate the degree of material damage and the resulting deterioration of material properties. The main task of this article is to present the state of knowledge on the possibility of taking into account the impact of cutting the core sheets of electric motors on core losses and their impact on the efficiency of the machine. This is a significant problem due to the need to design and manufacture energy-saving electric motors powered with a voltage of 20 to 350 Hz, whose magnetic cores are made of laminates. However, the performed analysis indicates the most important parameters of the cutting process, affecting the degree of material structure destruction. The method of the solution proposed by the authors for core punching and laser cutting, illustrated with a practical example, is also presented.
- Open Access
Practical Approximation of Sheet Losses Taking into Account the Guillotine and Laser Cutting Effect
Reducing losses in electrical devices is essential for reducing global energy consumption. Losses in the core of electrical machines constitute a significant part of the overall losses—their share increases with the number of machines powered by PWM converters, especially for high-speed machines. Limiting core losses requires precise determination at the design stage of the device. Achieving this goal is possible thanks to numerical or analytical simulation. A necessary input for this process is the correct determination of the properties of the core material. The sheet loss, however, changes due to the machining process, primarily punching. The subject of the work is to develop a sufficiently accurate approximation of electrical steel sheet-specific loss, taking into account the effects of cutting and the width of a given machine element for a wide range of induction and frequency. The method also enables the extrapolation of losses for higher frequencies relevant from the point of view of generating losses in the machine. The developed loss approximation can be used in the finite element simulation and in applying analytical methods. The technique can be successfully used for many grades of non-oriented sheet metal, provided that the requirements specified in the work are met. The proposed approximation allows us to determine the loss of a sample of a certain width in a wide range of magnetic induction magnitude and frequency with an accuracy not worse than 4%.
Open AccessPractical Approximation of Sheet Losses Taking into Account the Guillotine and Laser Cutting Effect
Reducing losses in electrical devices is essential for reducing global energy consumption. Losses in the core of electrical machines constitute a significant part of the overall losses—their share increases with the number of machines powered by PWM converters, especially for high-speed machines. Limiting core losses requires precise determination at the design stage of the device. Achieving this goal is possible thanks to numerical or analytical simulation. A necessary input for this process is the correct determination of the properties of the core material. The sheet loss, however, changes due to the machining process, primarily punching. The subject of the work is to develop a sufficiently accurate approximation of electrical steel sheet-specific loss, taking into account the effects of cutting and the width of a given machine element for a wide range of induction and frequency. The method also enables the extrapolation of losses for higher frequencies relevant from the point of view of generating losses in the machine. The developed loss approximation can be used in the finite element simulation and in applying analytical methods. The technique can be successfully used for many grades of non-oriented sheet metal, provided that the requirements specified in the work are met. The proposed approximation allows us to determine the loss of a sample of a certain width in a wide range of magnetic induction magnitude and frequency with an accuracy not worse than 4%.
- Open Access
- 31 July 2022
- Published by MDPI AG in Electronics
- Vol. 11 (15) , 2398
Design of High-Power Solid-State Transformers with Grain-Oriented Electrical Steel Cores
The paper proposes a simple structure of high-power solid-state transformers (SSTs) able to control the energy flow in critical lines of the medium-voltage (20 kV) distribution grid. With an increasing number of renewable intermittent sources connected at the nodes of the meshed distribution grid and a reduced number of nodes connected to large power plants, the distribution grid stability is more and more difficult to achieve. Control of the energy flow in critical lines can improve the stability of the distribution grid. This control can be provided by the proposed high-power SSTs operating a 20 kV with powers over 10 MW. This function is difficult to achieve with standard SST technologies that operate at high frequencies. These devices are made with expensive magnetic materials (amorphous or nanocrystalline cores) and a limited power by SST cells. The required total power is reached by assembling many SST cells. On the other hand, existing SST designs are mainly aimed at reducing the equipment’s size and it is difficult to design small objects able to operate at high voltages. The authors propose to use cores made with grain-oriented electrical steel (GOES) thin strips assembled in wound cores. Experimental results obtained, with GOES wound cores, show that the core losses are lower for a square voltage than for a sine one. This counterintuitive result is explained with an analytical calculus of eddy currents and confirmed by a non-linear time-stepping simulation. Therefore, simple converter structures, operating with rectangular voltages and low switching losses, are the best solutions. Experimental results also show that the core losses decrease with temperature. Consequently, high-power SST cells can be made with transformers whose GOES cores are hotter than coils for reducing core losses and keeping copper losses at low levels. The paper proposes an appropriate transformer mechanical structure that avoids any contact between the hot GOES wound core and the winding, with a specific cooling system and thermal insulation of the hot GOES wound core. The proposed design makes it possible to build SST cells over 1MW and full SSTs over 10 MW at moderate costs.
- 31 July 2022
- Published by MDPI AG in Electronics
- Vol. 11 (15) , 2398
Open AccessDesign of High-Power Solid-State Transformers with Grain-Oriented Electrical Steel Cores
The paper proposes a simple structure of high-power solid-state transformers (SSTs) able to control the energy flow in critical lines of the medium-voltage (20 kV) distribution grid. With an increasing number of renewable intermittent sources connected at the nodes of the meshed distribution grid and a reduced number of nodes connected to large power plants, the distribution grid stability is more and more difficult to achieve. Control of the energy flow in critical lines can improve the stability of the distribution grid. This control can be provided by the proposed high-power SSTs operating a 20 kV with powers over 10 MW. This function is difficult to achieve with standard SST technologies that operate at high frequencies. These devices are made with expensive magnetic materials (amorphous or nanocrystalline cores) and a limited power by SST cells. The required total power is reached by assembling many SST cells. On the other hand, existing SST designs are mainly aimed at reducing the equipment’s size and it is difficult to design small objects able to operate at high voltages. The authors propose to use cores made with grain-oriented electrical steel (GOES) thin strips assembled in wound cores. Experimental results obtained, with GOES wound cores, show that the core losses are lower for a square voltage than for a sine one. This counterintuitive result is explained with an analytical calculus of eddy currents and confirmed by a non-linear time-stepping simulation. Therefore, simple converter structures, operating with rectangular voltages and low switching losses, are the best solutions. Experimental results also show that the core losses decrease with temperature. Consequently, high-power SST cells can be made with transformers whose GOES cores are hotter than coils for reducing core losses and keeping copper losses at low levels. The paper proposes an appropriate transformer mechanical structure that avoids any contact between the hot GOES wound core and the winding, with a specific cooling system and thermal insulation of the hot GOES wound core. The proposed design makes it possible to build SST cells over 1MW and full SSTs over 10 MW at moderate costs.