James W. Murray
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
James W. Murray has a total of 85 co-authors. Here are the top co-authors by number of shared publications:
- Adam Thomas Clare
University of Nottingham
31 shared publications - Tanvir Hussain
Faculty of Engineering, University of Nottingham, Nottingham, UK
10 shared publications - Paul D. Brown
University of Nottingham
4 shared publications - David Graham McCartney
Department of Mechanical Engineering, University College London, London WC1E 7JE, UK
3 shared publications - David M. Grant
Advanced Materials Research Group, Faculty of Engineering, University of Nottingham, Nottingham, United Kingdom
3 shared publications - K. T. Voisey
University of Nottingham
3 shared publications
Latest Publications
- Open Access
- 19 May 2022
- Published by Elsevier in Additive Manufacturing Letters
- Vol. 3
Extending powder lifetime in additive manufacturing: Chemical etching of stainless steel spatter
- 19 May 2022
- Published by Elsevier in Additive Manufacturing Letters
- Vol. 3
Open AccessExtending powder lifetime in additive manufacturing: Chemical etching of stainless steel spatter
- 1 October 2021
- Published by Elsevier in International Journal of Machine Tools and Manufacture
- Vol. 169
Unprocessed machining chips as a practical feedstock in directed energy deposition
- 1 October 2021
- Published by Elsevier in International Journal of Machine Tools and Manufacture
- Vol. 169
Unprocessed machining chips as a practical feedstock in directed energy deposition
- 1 January 2021
- Published by Elsevier in CIRP Annals
- Vol. 70 (1) , 203-206
Interlaced layer thicknesses within single laser powder bed fusion geometries
- 1 January 2021
- Published by Elsevier in CIRP Annals
- Vol. 70 (1) , 203-206
Interlaced layer thicknesses within single laser powder bed fusion geometries
- 1 September 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 374, 21-31
Heat-treatment and mechanical properties of cold-sprayed high strength Al alloys from satellited feedstocks
- 1 September 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 374, 21-31
Heat-treatment and mechanical properties of cold-sprayed high strength Al alloys from satellited feedstocks
- 1 August 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 371, 97-106
Suspension high velocity oxy-fuel (SHVOF) spray of delta-theta alumina suspension: Phase transformation and tribology
- 1 August 2019
- Published by Elsevier in Surface and Coatings Technology
- Vol. 371, 97-106
Suspension high velocity oxy-fuel (SHVOF) spray of delta-theta alumina suspension: Phase transformation and tribology
- 1 May 2019
- Published by Elsevier in Powder Technology
- Vol. 350, 100-106
Spheroidisation of metal powder by pulsed electron beam irradiation
- 1 May 2019
- Published by Elsevier in Powder Technology
- Vol. 350, 100-106
Spheroidisation of metal powder by pulsed electron beam irradiation
- 1 January 2019
- Published by Elsevier in CIRP Annals
- Vol. 68 (1) , 177-180
Surface enhanced micro features using electrochemical jet processing
- 1 January 2019
- Published by Elsevier in CIRP Annals
- Vol. 68 (1) , 177-180
Surface enhanced micro features using electrochemical jet processing
- 1 December 2018
- Published by Elsevier in Additive Manufacturing
- Vol. 24, 486-497
Effect of post processing on the creep performance of laser powder bed fused Inconel 718
- 1 December 2018
- Published by Elsevier in Additive Manufacturing
- Vol. 24, 486-497
Effect of post processing on the creep performance of laser powder bed fused Inconel 718
- 1 October 2018
- Published by Elsevier in Materials & Design
- Vol. 155, 352-365
Defect-free TiC/Si multi-layer electrical discharge coatings
- 1 October 2018
- Published by Elsevier in Materials & Design
- Vol. 155, 352-365
Defect-free TiC/Si multi-layer electrical discharge coatings
- Open Access
- 28 September 2018
- Published by Springer Nature in Scientific Reports
- Vol. 8 (1) , 14530
Two step porosification of biomimetic thin-film hydroxyapatite/alpha-tri calcium phosphate coatings by pulsed electron beam irradiation
Here we show a new and effective methodology for rapid/controllable porosification of thin-film ceramics, which may be applied in medical devices/electronics and membrane nano-filtration. Dense hydroxyapatite applied to Ti6Al4V by plasma-assisted PVD was electron-beam irradiated to induce flash melting/boiling. Deposited coatings contained amorphous and nano-crystalline/stoichiometric hydroxyapatite (~35 nm). Irradiation (voltages 13–29 kV) led to ablation (up to 45% mass loss) and average/maximum pore areas from (0.07–1.66)/(0.69–92.53) μm2, mimicking the human cortical bone. Vitrification above 1150 °C formed (~62–30 nm) crystallites of α-Tri Calcium Phosphate. Unique porosification resulted from irradiation-induced sub-surface boiling and limited thermal conductivity of hydroxyapatite, causing material to expand/explode through the more quickly solidified top surface. Commercially applicable, roughened Ti6Al4V exacerbated the heating and boiling explosion phenomenon in certain regions, producing an array of pore sizes. Scaffold-like morphologies were generated by interconnection of micron/sub-micron porosity, showing great potential for facile generation of a biomimetic surface treatment for osseointegration.
- 28 September 2018
- Published by Springer Nature in Scientific Reports
- Vol. 8 (1) , 14530
Open AccessTwo step porosification of biomimetic thin-film hydroxyapatite/alpha-tri calcium phosphate coatings by pulsed electron beam irradiation
Here we show a new and effective methodology for rapid/controllable porosification of thin-film ceramics, which may be applied in medical devices/electronics and membrane nano-filtration. Dense hydroxyapatite applied to Ti6Al4V by plasma-assisted PVD was electron-beam irradiated to induce flash melting/boiling. Deposited coatings contained amorphous and nano-crystalline/stoichiometric hydroxyapatite (~35 nm). Irradiation (voltages 13–29 kV) led to ablation (up to 45% mass loss) and average/maximum pore areas from (0.07–1.66)/(0.69–92.53) μm2, mimicking the human cortical bone. Vitrification above 1150 °C formed (~62–30 nm) crystallites of α-Tri Calcium Phosphate. Unique porosification resulted from irradiation-induced sub-surface boiling and limited thermal conductivity of hydroxyapatite, causing material to expand/explode through the more quickly solidified top surface. Commercially applicable, roughened Ti6Al4V exacerbated the heating and boiling explosion phenomenon in certain regions, producing an array of pore sizes. Scaffold-like morphologies were generated by interconnection of micron/sub-micron porosity, showing great potential for facile generation of a biomimetic surface treatment for osseointegration.