Khac Duc Do
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Khac Duc Do has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Jie Pan
School of Mechanical and Chemical Engineering, The University of Western Australia, Perth, Western Australia 6009, Australia
4 shared publications Ke Wang
Department of Mechanical Engineering, Curtin University, Perth, WA 6102, Australia
3 shared publications- Lei Cui
Curtin University
3 shared publications Cheng-Heng Fua
Nat. Univ. of Singapore, Singapore
2 shared publicationsJ. Pan
2 shared publicationsJie Pan
2 shared publications
Latest Publications
- Open Access
- 23 January 2025
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 147 (5) , 1-14
Stabilization of a Rigid Body in Two Fluids With Surface Tension
This paper poses and solves a stabilization problem of a rigid body governed by nonlinear differential equations in two viscous incompressible fluids governed by Navier–Stokes equations (NSEs), where surface tension of the interface between the two fluids is considered, in a bounded domain in three dimensional space. Since only weak solutions of the NSEs exist globally while global existence of their strong/smooth solutions is a millennium problem, point-wise fluid forces and moments acting on the rigid body are not able to bound. This difficulty is overcome by designing an appropriate control law and performing stability analysis of the closed-loop system including the NSEs and surface tension, where “work and power of the two fluids” instead of forces and moments on the rigid body are used. A simulation is included to illustrate the results.
- 23 January 2025
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 147 (5) , 1-14
Open AccessStabilization of a Rigid Body in Two Fluids With Surface Tension
This paper poses and solves a stabilization problem of a rigid body governed by nonlinear differential equations in two viscous incompressible fluids governed by Navier–Stokes equations (NSEs), where surface tension of the interface between the two fluids is considered, in a bounded domain in three dimensional space. Since only weak solutions of the NSEs exist globally while global existence of their strong/smooth solutions is a millennium problem, point-wise fluid forces and moments acting on the rigid body are not able to bound. This difficulty is overcome by designing an appropriate control law and performing stability analysis of the closed-loop system including the NSEs and surface tension, where “work and power of the two fluids” instead of forces and moments on the rigid body are used. A simulation is included to illustrate the results.
- 11 November 2022
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 145 (2)
Inverse Optimal Control for Maximizing Harvested Energy From Dynamical Systems
This paper formulates and solves a new problem of inverse optimal control to maximize harvested energy from dynamical systems induced by external excitations. An inverse optimal control law is designed to minimize a cost function penalizing negativeness of the harvested energy and positiveness of the control and system (partial) states, where it does not require to solve a Hamilton–Jacobi–Belman (HJB) equation or a Hamilton–Jacobi–Isaacs (HJI) equation. An application to a point absorber wave energy converter (PAWEC) is included to illustrate the effectiveness of the proposed theory.
- 11 November 2022
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 145 (2)
Inverse Optimal Control for Maximizing Harvested Energy From Dynamical Systems
This paper formulates and solves a new problem of inverse optimal control to maximize harvested energy from dynamical systems induced by external excitations. An inverse optimal control law is designed to minimize a cost function penalizing negativeness of the harvested energy and positiveness of the control and system (partial) states, where it does not require to solve a Hamilton–Jacobi–Belman (HJB) equation or a Hamilton–Jacobi–Isaacs (HJI) equation. An application to a point absorber wave energy converter (PAWEC) is included to illustrate the effectiveness of the proposed theory.
- 4 May 2022
- Published by Taylor & Francis in International Journal of Control
- Vol. 96 (7) , 1817-1833
Almost global practical exponential stabilisation of a floating rigid body
This paper designs a control law based on an extension of the forwarding method to solve the problem of almost global practical exponential stabilization of a rigid body floating on the interface between viscous incompressible air and water governed by Navier-Stokes equations in a bounded domain in three dimensional space, where “almost” means no collision between the rigid body and the domain boundary. Since less regularity of initial data (hence a weak solution) is considered, the forces and moments induced by the air and water on the rigid body are not possible to be bounded. Therefore, we derive bound of “work and power of air and water” on the rigid body for use in stability and convergence analysis of the closed-loop system.
- 4 May 2022
- Published by Taylor & Francis in International Journal of Control
- Vol. 96 (7) , 1817-1833
Almost global practical exponential stabilisation of a floating rigid body
This paper designs a control law based on an extension of the forwarding method to solve the problem of almost global practical exponential stabilization of a rigid body floating on the interface between viscous incompressible air and water governed by Navier-Stokes equations in a bounded domain in three dimensional space, where “almost” means no collision between the rigid body and the domain boundary. Since less regularity of initial data (hence a weak solution) is considered, the forces and moments induced by the air and water on the rigid body are not possible to be bounded. Therefore, we derive bound of “work and power of air and water” on the rigid body for use in stability and convergence analysis of the closed-loop system.
- 21 February 2022
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 144 (5)
Stochastic Simultaneous Stabilization and Parking Control of the Brockett Integrator
This paper proposes a design of stochastic control laws for simultaneous stabilization and tracking control of the Brockett integrator based on Lyapunov's direct method, recent developments in stabilization of stochastic systems, Itôs formula for nonsmooth (weakly differentiable) functions, several inequalities. The control laws use two independent Wiener processes with the same covariance. The proposed control design guarantees κ∞-exponential or even finite-time stability of the closed-loop system in probability.
- 21 February 2022
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 144 (5)
Stochastic Simultaneous Stabilization and Parking Control of the Brockett Integrator
This paper proposes a design of stochastic control laws for simultaneous stabilization and tracking control of the Brockett integrator based on Lyapunov's direct method, recent developments in stabilization of stochastic systems, Itôs formula for nonsmooth (weakly differentiable) functions, several inequalities. The control laws use two independent Wiener processes with the same covariance. The proposed control design guarantees κ∞-exponential or even finite-time stability of the closed-loop system in probability.
- 3 January 2022
- Published by Taylor & Francis in International Journal of Control
- Vol. 96 (4) , 935-948
Boundary feedback stabilisation of a viscous incompressible fluid in a bounded domain
This paper presents a boundary feedback control design based on Lyapunov's direct method to globally practically exponentially stabilize a viscous incompressible fluid governed by Navier-Stokes equations at its equilibrium state in a bounded domain in three dimensional space. The control is implemented on a part of the rigid boundary and requires only boundary measurements. The Rothe method and an elliptic approximation are used to handle the time-dependent domain due to the boundary control in the proof of global existence of a weak solution of the closed-loop system. Due to consideration of less regular initial values of the fluid velocity (i.e., a global weak solution of the closed-loop system is obtained), the forces induced by the fluid on the part of the boundary, on which the control is implemented, are not able to bound. Thus, the paper derives the bound on “fluid work” on that part of the boundary in stability and convergence analysis of the closed-loop system. The advantage of considering the weak solution is its global existence and less regularity of the initial data versus local existence of strong solution requiring more regularity of the initial data.
- 3 January 2022
- Published by Taylor & Francis in International Journal of Control
- Vol. 96 (4) , 935-948
Boundary feedback stabilisation of a viscous incompressible fluid in a bounded domain
This paper presents a boundary feedback control design based on Lyapunov's direct method to globally practically exponentially stabilize a viscous incompressible fluid governed by Navier-Stokes equations at its equilibrium state in a bounded domain in three dimensional space. The control is implemented on a part of the rigid boundary and requires only boundary measurements. The Rothe method and an elliptic approximation are used to handle the time-dependent domain due to the boundary control in the proof of global existence of a weak solution of the closed-loop system. Due to consideration of less regular initial values of the fluid velocity (i.e., a global weak solution of the closed-loop system is obtained), the forces induced by the fluid on the part of the boundary, on which the control is implemented, are not able to bound. Thus, the paper derives the bound on “fluid work” on that part of the boundary in stability and convergence analysis of the closed-loop system. The advantage of considering the weak solution is its global existence and less regularity of the initial data versus local existence of strong solution requiring more regularity of the initial data.
- 6 December 2021
- Published by Taylor & Francis in International Journal of Control
- Vol. 96 (3) , 684-698
Forwarding inverse optimal formation control design for stochastic mobile agents
This paper proposes a new forwarding design of inverse optimal formation control laws for mobile agents with limited sensing ranges and driven by both deterministic and stochastic disturbances (drifts, diffusions, and jumps). The disturbances are allowed to be functions of arbitrarily high order polynomial of agent velocities. The proposed control laws guarantee that there is no collision between any agents, and a cost functional penalizing both states and controls without having to solve a Hamilton-Jacobi-Bellman equation or a Hamilton-Jaccobi-Isaacs equation. The control design is based on flexibility of the forwarding method.
- 6 December 2021
- Published by Taylor & Francis in International Journal of Control
- Vol. 96 (3) , 684-698
Forwarding inverse optimal formation control design for stochastic mobile agents
This paper proposes a new forwarding design of inverse optimal formation control laws for mobile agents with limited sensing ranges and driven by both deterministic and stochastic disturbances (drifts, diffusions, and jumps). The disturbances are allowed to be functions of arbitrarily high order polynomial of agent velocities. The proposed control laws guarantee that there is no collision between any agents, and a cost functional penalizing both states and controls without having to solve a Hamilton-Jacobi-Bellman equation or a Hamilton-Jaccobi-Isaacs equation. The control design is based on flexibility of the forwarding method.
- 19 April 2021
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 39 (12) , 2306-2332
Global inverse optimal exponential path-tracking control of mobile robots driven by Lévy processes
This paper formulates and solves a new problem of global practical inverse optimal exponential path-tracking control of mobile robots driven by Lévy processes with unknown characteristics. The control design is based on a new inverse optimal control design for nonlinear systems driven by Lévy processes and ensures global practical exponential stability almost surely and in the pth moment for the path-tracking errors. Moreover, it minimizes cost function that penalizes tracking errors and control torques without having to solve a Hamilton–Jacobi–Bellman or Hamilton–Jaccobi–Isaacs equation.
- 19 April 2021
- Published by Cambridge University Press (CUP) in Robotica
- Vol. 39 (12) , 2306-2332
Global inverse optimal exponential path-tracking control of mobile robots driven by Lévy processes
This paper formulates and solves a new problem of global practical inverse optimal exponential path-tracking control of mobile robots driven by Lévy processes with unknown characteristics. The control design is based on a new inverse optimal control design for nonlinear systems driven by Lévy processes and ensures global practical exponential stability almost surely and in the pth moment for the path-tracking errors. Moreover, it minimizes cost function that penalizes tracking errors and control torques without having to solve a Hamilton–Jacobi–Bellman or Hamilton–Jaccobi–Isaacs equation.
- 1 March 2021
- Published by Elsevier in IFAC Journal of Systems and Control
- Vol. 15
Global inverse optimal control of vertical take-off and landing aircraft
- 1 March 2021
- Published by Elsevier in IFAC Journal of Systems and Control
- Vol. 15
Global inverse optimal control of vertical take-off and landing aircraft
- 7 January 2021
- Published by Taylor & Francis in International Journal of Control
- Vol. 95 (6) , 1611-1624
Design of feedback stabilisers using Wiener processes for nonlinear systems
A Lyapunov-type theorem is developed to design feedback-stabilizers using Wiener processes for dynamical systems that can contain non-vanishing disturbances and arbitrarily nonlinear growths in their system functions. The proposed stabilizers guarantee that the resulting closed-loop system is globally well-posed, and is globally practically -exponentially -stable, almost surely globally practically -exponentially stable, and globally practically -exponentially stable in probability. Examples on a highly nonlinear system and mobile robots are included to illustrate the fact that although the theory is complicated, its application is straightforward. It is shown that the developed stabilizers can be applied to stabilize dynamical systems that cannot be stabilized by existing deterministic control laws.- 7 January 2021
- Published by Taylor & Francis in International Journal of Control
- Vol. 95 (6) , 1611-1624
Design of feedback stabilisers using Wiener processes for nonlinear systems
A Lyapunov-type theorem is developed to design feedback-stabilizers using Wiener processes for dynamical systems that can contain non-vanishing disturbances and arbitrarily nonlinear growths in their system functions. The proposed stabilizers guarantee that the resulting closed-loop system is globally well-posed, and is globally practically -exponentially -stable, almost surely globally practically -exponentially stable, and globally practically -exponentially stable in probability. Examples on a highly nonlinear system and mobile robots are included to illustrate the fact that although the theory is complicated, its application is straightforward. It is shown that the developed stabilizers can be applied to stabilize dynamical systems that cannot be stabilized by existing deterministic control laws.- 30 November 2020
- Published by Wiley in Asian Journal of Control
- Vol. 24 (1) , 16-45
Nonlinear control with wave observer to maximize harvested power for point absorber wave energy converters
This paper designs control laws that maximize the harvested power for submerged point absorber wave energy converters (PAWECs) constrained to heave motion. First, a mathematical model of a submerged PAWEC driven by nonlinear hydrodynamic, friction, restoring, and harvested power forces is derived. Second, a new disturbance observer is designed that globally practically exponentially estimate the wave velocity and its time derivatives. Next, the optimal operating points are derived such that when the PAWEC operates at these points, the harvested power is maximized. Fourth, nonlinear control laws are designed to track the optimal operating points based on the proposed disturbance observer and Lyapunov's direct method. In addition to maximize the harvested power, these optimal control laws ensure that the harvested power is always nonnegative; i.e., no power is drawn from the network to the PAWEC at any time. For comparison, a control law that maximizes the hydrodynamic extraction power is also designed. Several simulations are carried out and illustrate that the maximizing harvested power control yields better results than others.
- 30 November 2020
- Published by Wiley in Asian Journal of Control
- Vol. 24 (1) , 16-45
Nonlinear control with wave observer to maximize harvested power for point absorber wave energy converters
This paper designs control laws that maximize the harvested power for submerged point absorber wave energy converters (PAWECs) constrained to heave motion. First, a mathematical model of a submerged PAWEC driven by nonlinear hydrodynamic, friction, restoring, and harvested power forces is derived. Second, a new disturbance observer is designed that globally practically exponentially estimate the wave velocity and its time derivatives. Next, the optimal operating points are derived such that when the PAWEC operates at these points, the harvested power is maximized. Fourth, nonlinear control laws are designed to track the optimal operating points based on the proposed disturbance observer and Lyapunov's direct method. In addition to maximize the harvested power, these optimal control laws ensure that the harvested power is always nonnegative; i.e., no power is drawn from the network to the PAWEC at any time. For comparison, a control law that maximizes the hydrodynamic extraction power is also designed. Several simulations are carried out and illustrate that the maximizing harvested power control yields better results than others.