Olayinka Omowunmi Adewumi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Olayinka Omowunmi Adewumi has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Ayowole Oyediran
2 shared publications- Theophilus Fashanu
Systems Engineering, University of Lagos, Lagos State, Nigeria
2 shared publications - Adekunle Adetayo Yekini
Lagos State University of Science and Technology
1 shared publication - Adeshina Adegoke
Department of Mechanical Engineering, University of Lagos, Nigeria
1 shared publication Adeshina S. Adegoke
1 shared publication- Antonio Marcos de Oliveira Siqueira
Universidade Federal de Viçosa, Brazil
1 shared publication
Latest Publications
- Open Access
- 15 October 2024
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 10 (10) , 21156
Computational Heat Transfer and Entropy Generation Analysis of Natural Convection in a Trapezoidal Cavity
A numerical study is carried out to investigate natural convective heat transfer process in a water-filled trapezoidal cavity heated from below using finite volume method in solving the governing equations. The study examined the effects of Rayleigh number (Ra = 101-106), heat source length (Ls = 0.1-0.9), angle of inclination (teta = 0º-75º) on the Nusselt number (Nu) and entropy generation of the trapezoidal cavity. The results of the investigation indicate that Nu increases when the source length increases, and the angle of inclination decreases. Also, Nu also increases with Ra when the source length and inclination angle are fixed. The total entropy is dominated by thermal entropy generation (Sthermal) and is seen to increase with source length. The results presented in isotherms and streamlines indicate that viscous and buoyancy forces are significant in the trapezoidal cavity.
- 15 October 2024
- Published by Universidade Federal de Vicosa in The Journal of Engineering and Exact Sciences
- Vol. 10 (10) , 21156
Open AccessComputational Heat Transfer and Entropy Generation Analysis of Natural Convection in a Trapezoidal Cavity
A numerical study is carried out to investigate natural convective heat transfer process in a water-filled trapezoidal cavity heated from below using finite volume method in solving the governing equations. The study examined the effects of Rayleigh number (Ra = 101-106), heat source length (Ls = 0.1-0.9), angle of inclination (teta = 0º-75º) on the Nusselt number (Nu) and entropy generation of the trapezoidal cavity. The results of the investigation indicate that Nu increases when the source length increases, and the angle of inclination decreases. Also, Nu also increases with Ra when the source length and inclination angle are fixed. The total entropy is dominated by thermal entropy generation (Sthermal) and is seen to increase with source length. The results presented in isotherms and streamlines indicate that viscous and buoyancy forces are significant in the trapezoidal cavity.
- 7 April 2023
- Published by Elsevier in Ocean Engineering
- Vol. 278
Modelling and nonlinear analysis of the wave-induced vibrations of a single hybrid riser conveying two-phase flow
- 7 April 2023
- Published by Elsevier in Ocean Engineering
- Vol. 278
Modelling and nonlinear analysis of the wave-induced vibrations of a single hybrid riser conveying two-phase flow
- Open Access
- 1 December 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1378 (2) , 022003
Characterization of a Finned Heat Sink for a Power Inverter
Heat is a by-product which is constantly being generated in the operation of a power inverter and if left unchecked will inevitably lead to the damage of the device. Hence a means to efficiently dissipate this heat has to be employed. In this research, a heat sink is mathematically modelled and its thermal performance was evaluated using ANSYS software and experimentally validated. The optimisation of the heat sink was done with the aid of the FMINCON optimization tool in MATLAB. A K-type thermocouple and a three channel temperature logger, MTM-380SD, with real time data logger were used to obtain temperature data of the heat sink for the purpose of experimental validation. The optimized heat sink parameters are heat sink length and width, number of fins, base thickness, fin height, thickness and spacing. Results show that the percentage deviation between the simulation and experimental temperature results for a pulse load of 300W is 8%, for a pulse load of 460W is 3%, for a pulse load of 600W is 8%, for a pulse load of 1015W is 2%. The maximum simulated and experimented temperatures are 84°C and 85.4°C. Thus the inverter can be safely and reliably operated.
- 1 December 2019
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 1378 (2) , 022003
Open AccessCharacterization of a Finned Heat Sink for a Power Inverter
Heat is a by-product which is constantly being generated in the operation of a power inverter and if left unchecked will inevitably lead to the damage of the device. Hence a means to efficiently dissipate this heat has to be employed. In this research, a heat sink is mathematically modelled and its thermal performance was evaluated using ANSYS software and experimentally validated. The optimisation of the heat sink was done with the aid of the FMINCON optimization tool in MATLAB. A K-type thermocouple and a three channel temperature logger, MTM-380SD, with real time data logger were used to obtain temperature data of the heat sink for the purpose of experimental validation. The optimized heat sink parameters are heat sink length and width, number of fins, base thickness, fin height, thickness and spacing. Results show that the percentage deviation between the simulation and experimental temperature results for a pulse load of 300W is 8%, for a pulse load of 460W is 3%, for a pulse load of 600W is 8%, for a pulse load of 1015W is 2%. The maximum simulated and experimented temperatures are 84°C and 85.4°C. Thus the inverter can be safely and reliably operated.
- 1 November 2013
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 66, 315-323
Constructal design of combined microchannel and micro pin fins for electronic cooling
- 1 November 2013
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 66, 315-323
Constructal design of combined microchannel and micro pin fins for electronic cooling