Mohammad Lotfi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Mohammad Lotfi has a total of 30 co-authors. Here are the top co-authors by number of shared publications:
- Saeid Amini
Department of Manufacturing, Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
13 shared publications Saeid Amini
8 shared publications- Ali Akhavan Farid
Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham Malaysia, Semenyih, Malaysia
6 shared publications Mohsen Aghaei
5 shared publicationsMahnoush Alinaghian
3 shared publicationsReza Teimouri
3 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by Negah Scientific Publisher in Journal of Research and Health
- Vol. 16 (1) , 103-110
The Relationship Between Particulate Matter and Body Mass Index in Osteoporosis
A strong relationship is observed between air pollution and a higher risk of being overweight or obese, reduced bone mineral density (BMD), and an increased likelihood of osteoporosis. This study aimed to examine the relationship between suspended particles and body mass index (BMI) in patients with osteoporosis and osteopenia. Data on particulate ...
- 1 January 2026
- Published by Negah Scientific Publisher in Journal of Research and Health
- Vol. 16 (1) , 103-110
Open AccessThe Relationship Between Particulate Matter and Body Mass Index in Osteoporosis
A strong relationship is observed between air pollution and a higher risk of being overweight or obese, reduced bone mineral density (BMD), and an increased likelihood of osteoporosis. This study aimed to examine the relationship between suspended particles and body mass index (BMI) in patients with osteoporosis and osteopenia. Data on particulate ...
- Open Access
- 1 December 2019
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 2 (4) , 397-406
Sustainable drilling process of 1045 steel plates regarding minimum energy consumption and desired work quality
- 1 December 2019
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 2 (4) , 397-406
Open AccessSustainable drilling process of 1045 steel plates regarding minimum energy consumption and desired work quality
- 10 October 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine
- Vol. 233 (12) , 1226-1236
Improving the surface energy of titanium implants by the creation of hierarchical textures on the surface via three-dimensional elliptical vibration turning for enhanced osseointegration
An increase in bone-implant contact and an increase in surface hydrophilicity are the two important factors involved in improving osseointegration. Therefore, three-dimensional elliptical vibration turning method is applied to increase the hydrophilicity of titanium surface by the generation of hierarchical nano- and micro-textures. That being the case, face turning process at different cutting conditions is carried out in this research. Surface roughness and the contact angle of water drops with machined surfaces were selected to be measured for the analysis of surface hydrophilicity. The results show that an additional surface area can be achieved by the generation of micro- or nano-textures, resulting in a lower contact angle. Furthermore, intermittent movement of cutting tool in vibration cutting causes the process to be more stable, achieving the desired range of surface roughness.
- 10 October 2019
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine
- Vol. 233 (12) , 1226-1236
Improving the surface energy of titanium implants by the creation of hierarchical textures on the surface via three-dimensional elliptical vibration turning for enhanced osseointegration
An increase in bone-implant contact and an increase in surface hydrophilicity are the two important factors involved in improving osseointegration. Therefore, three-dimensional elliptical vibration turning method is applied to increase the hydrophilicity of titanium surface by the generation of hierarchical nano- and micro-textures. That being the case, face turning process at different cutting conditions is carried out in this research. Surface roughness and the contact angle of water drops with machined surfaces were selected to be measured for the analysis of surface hydrophilicity. The results show that an additional surface area can be achieved by the generation of micro- or nano-textures, resulting in a lower contact angle. Furthermore, intermittent movement of cutting tool in vibration cutting causes the process to be more stable, achieving the desired range of surface roughness.
- 5 September 2019
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 26 (08)
OPTIMUM FLANK WEAR OF TiAlN-COATED TOOL: TOWARD PRODUCTIVE ROUGH CUTTING OF INCONEL 625
Long tool life and high material removal rate (MRR) are the two essential requirements in rough cutting of materials. The rapid rate of the flank wear propagation in machining of nickel-based superalloys has induced the utilization of low cutting parameters when the goal was set to maximize the tool life based on the machining time or cutting length. However, this method may not provide an effective rate for the material being cut. This work presents two mathematical models to find the optimum cutting parameters results for the minimum flank wear and maximum MRR. Experimental tests were carried out based on the central composite design (CCD) in rough cutting of Inconel 625 by using TiAlN-coated insert. Maximum flank wear was measured to determine the tool wear propagation. The wear mechanisms which contribute in the tool wear were analyzed by using scanning electron microscope (SEM) to evaluate the effects of cutting parameters on the flank wear propagation. The results showed that cutting speed and depth of cut had the most significant effect on the tool wear. However, optimum cutting condition was achieved by reducing the cutting speed when feed rate and depth of cut maintained at the highest level. This was associated to the interaction of cutting speed and depth of cut, and predominant of abrasion and notching at their highest levels, respectively.
- 5 September 2019
- Published by World Scientific Pub Co Pte Ltd in Surface Review and Letters
- Vol. 26 (08)
OPTIMUM FLANK WEAR OF TiAlN-COATED TOOL: TOWARD PRODUCTIVE ROUGH CUTTING OF INCONEL 625
Long tool life and high material removal rate (MRR) are the two essential requirements in rough cutting of materials. The rapid rate of the flank wear propagation in machining of nickel-based superalloys has induced the utilization of low cutting parameters when the goal was set to maximize the tool life based on the machining time or cutting length. However, this method may not provide an effective rate for the material being cut. This work presents two mathematical models to find the optimum cutting parameters results for the minimum flank wear and maximum MRR. Experimental tests were carried out based on the central composite design (CCD) in rough cutting of Inconel 625 by using TiAlN-coated insert. Maximum flank wear was measured to determine the tool wear propagation. The wear mechanisms which contribute in the tool wear were analyzed by using scanning electron microscope (SEM) to evaluate the effects of cutting parameters on the flank wear propagation. The results showed that cutting speed and depth of cut had the most significant effect on the tool wear. However, optimum cutting condition was achieved by reducing the cutting speed when feed rate and depth of cut maintained at the highest level. This was associated to the interaction of cutting speed and depth of cut, and predominant of abrasion and notching at their highest levels, respectively.
- 1 September 2019
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 160, 241-254
Development of a friction model based on oblique cutting theory
- 1 September 2019
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 160, 241-254
Development of a friction model based on oblique cutting theory
- Open Access
- 1 September 2019
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 2 (3) , 235-240
Wettability analysis of titanium alloy in 3D elliptical ultrasonic assisted turning
- 1 September 2019
- Published by KEAI Publishing in International Journal of Lightweight Materials and Manufacture
- Vol. 2 (3) , 235-240
Open AccessWettability analysis of titanium alloy in 3D elliptical ultrasonic assisted turning
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Machining and Machinability of Materials
- Vol. 21 (4) , 321
Tool wear deceleration in turning of Inconel 625
- 1 January 2019
- Published by Inderscience Publishers in International Journal of Machining and Machinability of Materials
- Vol. 21 (4) , 321
Tool wear deceleration in turning of Inconel 625
- 15 November 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 233 (4) , 824-838
Theoretical and numerical modeling of tool–chip friction in ultrasonic-assisted turning
Decrease of friction in tool–chip contact zone is a key subject in metal cutting operation. Therefore, effect of ultrasonic vibration in this area is analyzed by using experimental and simulation methods. In this study, a theoretical model is firstly developed based on the shear friction model, and then sticking–sliding contact zones plus their contact lengths are defined in order to simulate conventional and ultrasonic-assisted turning. Accordingly, shear angle, sticky length, and cutting forces were measured in experiments as input parameters for the calculation of friction coefficients. As a result, intermittent contact of vibrated tool decreases the time of thermal conduction in tool–chip interface, resulting in a significant reduction in friction coefficient and contact length, particularly, in sticky region.
- 15 November 2018
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 233 (4) , 824-838
Theoretical and numerical modeling of tool–chip friction in ultrasonic-assisted turning
Decrease of friction in tool–chip contact zone is a key subject in metal cutting operation. Therefore, effect of ultrasonic vibration in this area is analyzed by using experimental and simulation methods. In this study, a theoretical model is firstly developed based on the shear friction model, and then sticking–sliding contact zones plus their contact lengths are defined in order to simulate conventional and ultrasonic-assisted turning. Accordingly, shear angle, sticky length, and cutting forces were measured in experiments as input parameters for the calculation of friction coefficients. As a result, intermittent contact of vibrated tool decreases the time of thermal conduction in tool–chip interface, resulting in a significant reduction in friction coefficient and contact length, particularly, in sticky region.
- 1 September 2018
- Published by Elsevier in Simulation Modelling Practice and Theory
- Vol. 87, 226-238
Tool wear modeling in rotary turning modified by ultrasonic vibration
- 1 September 2018
- Published by Elsevier in Simulation Modelling Practice and Theory
- Vol. 87, 226-238
Tool wear modeling in rotary turning modified by ultrasonic vibration
- 1 August 2018
- Published by Elsevier in Ultrasonics
- Vol. 88, 106-114
3D FEM simulation of tool wear in ultrasonic assisted rotary turning
- 1 August 2018
- Published by Elsevier in Ultrasonics
- Vol. 88, 106-114
3D FEM simulation of tool wear in ultrasonic assisted rotary turning