Saeid Amini
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Saeid Amini has a total of 72 co-authors. Here are the top co-authors by number of shared publications:
- Mohammad Lotfi
Department of Manufacturing, Faculty of Mechanical Engineering, University of Kashan, Kashan, Iran
13 shared publications - Mohammad Baraheni
Arak University of Technology
6 shared publications Reza Teimouri
6 shared publicationsHossein Paktinat
Department of Manufacturing, Faculty of Mechanical Engineering, University of Kashan, Kashan 8731753153, Iran
5 shared publicationsMohsen Aghaei
5 shared publicationsA. Barani
Department of Mechanical Engineering, Isfahan University of Technology, Isfahan, Iran
4 shared publications
Latest Publications
- 3 October 2026
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48  (11) , 766
Ultrasonic vibration effects on machining deformation and residual stress in precision milling of Al-7075
- 3 October 2026
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 48  (11) , 766
Ultrasonic vibration effects on machining deformation and residual stress in precision milling of Al-7075
- 8 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Experimental analysis of chip-breaker geometry effects on cutting forces, thermal load, and surface quality in turning AISI 304 stainless steel
This study experimentally investigates the influence of chip-breaker geometry on cutting forces, temperature, material removal rate, chip formation, and surface quality during the dry turning of AISI 304 stainless steel. Three chip-breaker geometries (A, B, and C) were evaluated using a full factorial experimental design with spindle speeds of 500, 710, and 1000 r/min and feed rates of 0.08, 0.12, and 0.16 mm/rev. The results showed that increasing the spindle speed reduced cutting forces and maximum cutting temperature, whereas increasing the feed rate led to higher mechanical and thermal loads. Among the investigated geometries, chip-breaker type B exhibited the most favorable overall performance, reducing cutting forces and temperature by approximately 20–25% compared with types A and C while simultaneously improving the surface quality. Chip morphology analysis revealed that type A generated the smallest chip curl radius, whereas type B produced the lowest chip thickness, indicating more favorable chip-flow conditions and reduced chip compression. The experimentally measured material removal rate values for type B were approximately 35% higher than those of type A, although type C exhibited the highest material removal rate values at the expense of increased thermal loading. Overall, the results demonstrate that the chip-breaker geometry significantly affects the thermo-mechanical behavior of the turning process, and chip-breaker type B provides the most balanced combination of cutting performance, thermal stability, chip control, and surface integrity for machining AISI 304 stainless steel under dry cutting conditions.
- 8 August 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Experimental analysis of chip-breaker geometry effects on cutting forces, thermal load, and surface quality in turning AISI 304 stainless steel
This study experimentally investigates the influence of chip-breaker geometry on cutting forces, temperature, material removal rate, chip formation, and surface quality during the dry turning of AISI 304 stainless steel. Three chip-breaker geometries (A, B, and C) were evaluated using a full factorial experimental design with spindle speeds of 500, 710, and 1000 r/min and feed rates of 0.08, 0.12, and 0.16 mm/rev. The results showed that increasing the spindle speed reduced cutting forces and maximum cutting temperature, whereas increasing the feed rate led to higher mechanical and thermal loads. Among the investigated geometries, chip-breaker type B exhibited the most favorable overall performance, reducing cutting forces and temperature by approximately 20–25% compared with types A and C while simultaneously improving the surface quality. Chip morphology analysis revealed that type A generated the smallest chip curl radius, whereas type B produced the lowest chip thickness, indicating more favorable chip-flow conditions and reduced chip compression. The experimentally measured material removal rate values for type B were approximately 35% higher than those of type A, although type C exhibited the highest material removal rate values at the expense of increased thermal loading. Overall, the results demonstrate that the chip-breaker geometry significantly affects the thermo-mechanical behavior of the turning process, and chip-breaker type B provides the most balanced combination of cutting performance, thermal stability, chip control, and surface integrity for machining AISI 304 stainless steel under dry cutting conditions.
- 22 July 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Influence of ultrasonic peening treatment parameters on surface hardness, wear, and friction behavior of wire EDMed hardened Mo40 alloy steel
Wire Electrical Discharge Machining (WEDM) allows for the accurate machining of materials with high hardness and limited machinability but inherently generates tensile residual stresses and surface microcracks due to rapid thermal cycling. These defects can deteriorate the mechanical integrity and wear resistance of machined components.This research applied Ultrasonic Peening Treatment (UPT) as a cost-effective and practical post-processing approach aimed at improving the surface integrity, microhardness, and wear characteristics of WEDM-processed AISI 4140 (DIN 1.7225) steel. Specimens cut at discharge currents of 7, 9, and 15 A were treated to the UPT with feed rates ranging from 0.08 to 0.16 mm/rev and 1–5 passes. Surface roughness, microhardness, and wear behavior were characterized using profilometry, Vickers hardness testing, scanning electron microscopy (SEM), and pin-on-disc tribometry. A Taguchi L9 orthogonal array and ANOVA were applied to identify the dominant parameters influencing surface properties. The discharge current and peening feed rate were found to have the most significant effects (p < 0.05), with the optimal condition (15 A, 0.12 mm/rev, 3 passes) yielding a 48% increase in surface hardness, a hardened layer depth of approximately 200 μm, and a 65% reduction in wear rate relative to the untreated surface. SEM analyses revealed pronounced dislocation rearrangement and nanoscale grain refinement near the surface, confirming that the UPT effectively mitigates WEDM-induced tensile stresses and refines the microstructure. Overall, the combined WEDM–UPT process demonstrates a robust pathway for producing high-performance components with superior surface and mechanical properties.
- 22 July 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Influence of ultrasonic peening treatment parameters on surface hardness, wear, and friction behavior of wire EDMed hardened Mo40 alloy steel
Wire Electrical Discharge Machining (WEDM) allows for the accurate machining of materials with high hardness and limited machinability but inherently generates tensile residual stresses and surface microcracks due to rapid thermal cycling. These defects can deteriorate the mechanical integrity and wear resistance of machined components.This research applied Ultrasonic Peening Treatment (UPT) as a cost-effective and practical post-processing approach aimed at improving the surface integrity, microhardness, and wear characteristics of WEDM-processed AISI 4140 (DIN 1.7225) steel. Specimens cut at discharge currents of 7, 9, and 15 A were treated to the UPT with feed rates ranging from 0.08 to 0.16 mm/rev and 1–5 passes. Surface roughness, microhardness, and wear behavior were characterized using profilometry, Vickers hardness testing, scanning electron microscopy (SEM), and pin-on-disc tribometry. A Taguchi L9 orthogonal array and ANOVA were applied to identify the dominant parameters influencing surface properties. The discharge current and peening feed rate were found to have the most significant effects (p < 0.05), with the optimal condition (15 A, 0.12 mm/rev, 3 passes) yielding a 48% increase in surface hardness, a hardened layer depth of approximately 200 μm, and a 65% reduction in wear rate relative to the untreated surface. SEM analyses revealed pronounced dislocation rearrangement and nanoscale grain refinement near the surface, confirming that the UPT effectively mitigates WEDM-induced tensile stresses and refines the microstructure. Overall, the combined WEDM–UPT process demonstrates a robust pathway for producing high-performance components with superior surface and mechanical properties.
- 5 February 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine
- Vol. 240  (2) , 122-138
Ultrasonic-assisted micro-milling of cortical bone: An experimental study
Bone machining is a critical aspect of orthopedic surgeries, where excessive heat generation can cause thermal necrosis and hinder patient recovery. Ultrasonic-assisted micro-milling (UAM) offers advantages by reducing cutting forces and heat generation. This study examines the effects of feed rate, rotational speed, tool diameter, depth of cut, and vibration amplitude on cutting force and temperature in UAM of cortical bone. 64 experiments were performed on fresh bovine cortical bone specimens prepared to consistent dimensions and stored to prevent moisture loss. Repeated central points in the design quantified experimental error and repeatability. Precision, calibrated instruments ensured accurate force and temperature measurements. Data were analyzed using regression modeling and statistical methods. Results showed that increasing rotational speed and vibration amplitude generally reduced cutting force and temperature, while feed rate and tool diameter had complex interactive effects. Multi-objective optimization using NSGA-II identified optimal conditions: for the X-axis, 1047 rpm, 63 mm/min feed, 1.5 mm diameter, 0.6 mm depth, and 30 μm amplitude; for the Y-axis, 990 rpm, 22 mm/min, 0.8 mm diameter, 0.2 mm depth, and 20 μm amplitude. Predictive models achieved temperature errors of 1.6% (X) and 7.6% (Y), and force errors of 12.9% (X) and 14.5% (Y). These models can help surgeons anticipate cutting conditions preoperatively, reducing surgical risks and preserving bone integrity. The findings support optimization of orthopedic machining processes, improving surgical outcomes and advancing bone-milling techniques.
- 5 February 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part H: Journal of Engineering in Medicine
- Vol. 240  (2) , 122-138
Ultrasonic-assisted micro-milling of cortical bone: An experimental study
Bone machining is a critical aspect of orthopedic surgeries, where excessive heat generation can cause thermal necrosis and hinder patient recovery. Ultrasonic-assisted micro-milling (UAM) offers advantages by reducing cutting forces and heat generation. This study examines the effects of feed rate, rotational speed, tool diameter, depth of cut, and vibration amplitude on cutting force and temperature in UAM of cortical bone. 64 experiments were performed on fresh bovine cortical bone specimens prepared to consistent dimensions and stored to prevent moisture loss. Repeated central points in the design quantified experimental error and repeatability. Precision, calibrated instruments ensured accurate force and temperature measurements. Data were analyzed using regression modeling and statistical methods. Results showed that increasing rotational speed and vibration amplitude generally reduced cutting force and temperature, while feed rate and tool diameter had complex interactive effects. Multi-objective optimization using NSGA-II identified optimal conditions: for the X-axis, 1047 rpm, 63 mm/min feed, 1.5 mm diameter, 0.6 mm depth, and 30 μm amplitude; for the Y-axis, 990 rpm, 22 mm/min, 0.8 mm diameter, 0.2 mm depth, and 20 μm amplitude. Predictive models achieved temperature errors of 1.6% (X) and 7.6% (Y), and force errors of 12.9% (X) and 14.5% (Y). These models can help surgeons anticipate cutting conditions preoperatively, reducing surgical risks and preserving bone integrity. The findings support optimization of orthopedic machining processes, improving surgical outcomes and advancing bone-milling techniques.
- 2 December 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 142  (1-2) , 215-233
Distortion and residual stresses in ultrasonic assisted milling: FE analysis and experimental study
- 2 December 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 142  (1-2) , 215-233
Distortion and residual stresses in ultrasonic assisted milling: FE analysis and experimental study
- 3 October 2025
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 47  (12) , 1-31
An investigation of ultrasonic-assisted ball burnishing process: surface properties and work-hardening behavior of AISI 1045 steel
- 3 October 2025
- Published by Springer Nature in Journal of the Brazilian Society of Mechanical Sciences and Engineering
- Vol. 47  (12) , 1-31
An investigation of ultrasonic-assisted ball burnishing process: surface properties and work-hardening behavior of AISI 1045 steel
- 3 September 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Enhancing surface quality in ultrasonic vibration-assisted micro-milling of bone: A combined RSM-PSO approach and sensitivity analysis
This study presents a novel approach to optimizing surface roughness in ultrasonic vibration-assisted micro-milling (UVAMM) of cortical bone by integrating Response Surface Methodology (RSM) with Particle Swarm Optimization (PSO), complemented by global sensitivity analysis using Sobol indices. Unlike prior studies that focus on conventional bone machining or single-variable optimization, this research provides a multi-parametric and data-driven framework specifically tailored to address the anisotropic nature of bone tissue. Experiments were performed on bovine bone, a validated analog to human cortical bone, using key input variables such as spindle speed, feed rate, depth of cut, tool diameter, and ultrasonic vibration amplitude. A Central Composite Design (CCD) structured the experiments, with RSM-derived regression models optimized via PSO to identify parameter combinations minimizing surface roughness (Ra). Key findings include optimal parameter ranges: for the x -axis, spindle speed of 950 rpm, feed rate of 22 mm/min, tool diameter of 1.14 mm, depth of cut of 0.25 mm, and ultrasonic amplitude of 27 µm; for the y -axis, spindle speed of 950 rpm, feed rate of 22 mm/min, tool diameter of 1.30 mm, depth of cut of 0.50 mm, and ultrasonic amplitude of 26 µm, achieving surface roughness values of 0.30 µm ( x -axis) and 0.50 µm ( y -axis) with prediction errors under 7%. Sobol-based sensitivity analysis revealed direction-dependent (anisotropic) behavior in bone machining, underscoring the clinical relevance of cutting direction with respect to osteonal alignment. By providing a robust optimization-sensitivity framework tailored to the biomechanical complexity of bone, this work offers practical and innovative insights for enhancing surface integrity, precision, and osteointegration in orthopedic and dental procedures.
- 3 September 2025
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
Enhancing surface quality in ultrasonic vibration-assisted micro-milling of bone: A combined RSM-PSO approach and sensitivity analysis
This study presents a novel approach to optimizing surface roughness in ultrasonic vibration-assisted micro-milling (UVAMM) of cortical bone by integrating Response Surface Methodology (RSM) with Particle Swarm Optimization (PSO), complemented by global sensitivity analysis using Sobol indices. Unlike prior studies that focus on conventional bone machining or single-variable optimization, this research provides a multi-parametric and data-driven framework specifically tailored to address the anisotropic nature of bone tissue. Experiments were performed on bovine bone, a validated analog to human cortical bone, using key input variables such as spindle speed, feed rate, depth of cut, tool diameter, and ultrasonic vibration amplitude. A Central Composite Design (CCD) structured the experiments, with RSM-derived regression models optimized via PSO to identify parameter combinations minimizing surface roughness (Ra). Key findings include optimal parameter ranges: for the x -axis, spindle speed of 950 rpm, feed rate of 22 mm/min, tool diameter of 1.14 mm, depth of cut of 0.25 mm, and ultrasonic amplitude of 27 µm; for the y -axis, spindle speed of 950 rpm, feed rate of 22 mm/min, tool diameter of 1.30 mm, depth of cut of 0.50 mm, and ultrasonic amplitude of 26 µm, achieving surface roughness values of 0.30 µm ( x -axis) and 0.50 µm ( y -axis) with prediction errors under 7%. Sobol-based sensitivity analysis revealed direction-dependent (anisotropic) behavior in bone machining, underscoring the clinical relevance of cutting direction with respect to osteonal alignment. By providing a robust optimization-sensitivity framework tailored to the biomechanical complexity of bone, this work offers practical and innovative insights for enhancing surface integrity, precision, and osteointegration in orthopedic and dental procedures.
- 12 November 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240  (4) , 4260-4275
Delamination assessment and prediction in ultrasonic-assisted drilling of laminated hybrid composites
This study presents a novel application of the Random Forest (RF) algorithm to predict delamination in ultrasonic-assisted drilling (UAD) of carbon fiber reinforced polymers (CFRPs). It performs a multi-dimensional analysis of factors including graphene nanoplatelet (GNP) addition, ultrasonic vibration, cutting tool type, and feed rate on delamination damage. The RF algorithm was chosen for its ability to handle both regression and categorical tasks. The model demonstrated strong predictive performance, achieving an R² value of 0.9445 on test data, with a root mean squared error (RMSE) of 0.32% and a mean absolute error (MAE) of 0.29% relative to the average values. Analysis of variance (ANOVA), Sobol sensitivity, and Shapley additive explanations (SHAP) analysis were used to assess the impact of input parameters. Sobol identified the cutting tool type and feed rate as the most influential factors, contributing 37.7% and 34.3% to delamination variance, aligning with ANOVA findings. SHAP further confirmed the tooling type and feed rate as key factors, with contributions of 48.75% and 32.61%. The analyses revealed that GNPs increased delamination due to higher thrust forces, while ultrasonic vibration and high-cobalt tools reduced delamination. Optimal conditions were a feed rate of 0.08 mm/rev with an 8% cobalt tool and ultrasonic vibration, excluding GNPs.
- 12 November 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
- Vol. 240  (4) , 4260-4275
Delamination assessment and prediction in ultrasonic-assisted drilling of laminated hybrid composites
This study presents a novel application of the Random Forest (RF) algorithm to predict delamination in ultrasonic-assisted drilling (UAD) of carbon fiber reinforced polymers (CFRPs). It performs a multi-dimensional analysis of factors including graphene nanoplatelet (GNP) addition, ultrasonic vibration, cutting tool type, and feed rate on delamination damage. The RF algorithm was chosen for its ability to handle both regression and categorical tasks. The model demonstrated strong predictive performance, achieving an R² value of 0.9445 on test data, with a root mean squared error (RMSE) of 0.32% and a mean absolute error (MAE) of 0.29% relative to the average values. Analysis of variance (ANOVA), Sobol sensitivity, and Shapley additive explanations (SHAP) analysis were used to assess the impact of input parameters. Sobol identified the cutting tool type and feed rate as the most influential factors, contributing 37.7% and 34.3% to delamination variance, aligning with ANOVA findings. SHAP further confirmed the tooling type and feed rate as key factors, with contributions of 48.75% and 32.61%. The analyses revealed that GNPs increased delamination due to higher thrust forces, while ultrasonic vibration and high-cobalt tools reduced delamination. Optimal conditions were a feed rate of 0.08 mm/rev with an 8% cobalt tool and ultrasonic vibration, excluding GNPs.
- 24 October 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Experimental study of the effects of the ultrasonic peening treatment on residual stress, surface hardness, and hardness depth of parts cut with wire EDM
The Wire EDM process is widely utilized in diverse industries due to its numerous advantages. Residual stresses in wire EDMed workpieces, mainly due to non-uniformity in heat flux, metallurgical phase change, and inhomogeneous plastic deformation, are tensile and have large values ​​in surface layers. These residual stresses lead to the formation of surface cracks and a decrease in superficial mechanical strength. The Ultrasonic Peening Treatment (UPT) is an innovative approach used in this study to generate compressive residual stress and modify the surface structure of wire EDMed workpieces, as a cost-effective alternative to traditional methods. The study highlights UPT's potential as an effective way to modify the mechanical properties of wire EDMed workpieces. The impact of parameters such as the number of peening passes, feeding rate, and the type of wire EDM cut on the residual stress generated in MO40 (1.7225) alloy steel was thoroughly investigated. The experiments performed with the Taguchi method demonstrated that the UPT caused a shift in residual stress from tensile to compressive, with a maximum residual compressive stress of 1654 MPa. In the initial peening pass, an enhancement of 30%, 31%, and 48% in surface hardness values was noted for the semi-finishing, finishing, and roughing workpieces. The depth of hardness distribution reached 200 μm, while surface hardness decreased with an increased feeding rate. SEM images showed improved dislocation rearrangement due to ultrasonic vibrations, resulting in smaller surface layers, even at the nanoscale.
- 24 October 2024
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Experimental study of the effects of the ultrasonic peening treatment on residual stress, surface hardness, and hardness depth of parts cut with wire EDM
The Wire EDM process is widely utilized in diverse industries due to its numerous advantages. Residual stresses in wire EDMed workpieces, mainly due to non-uniformity in heat flux, metallurgical phase change, and inhomogeneous plastic deformation, are tensile and have large values ​​in surface layers. These residual stresses lead to the formation of surface cracks and a decrease in superficial mechanical strength. The Ultrasonic Peening Treatment (UPT) is an innovative approach used in this study to generate compressive residual stress and modify the surface structure of wire EDMed workpieces, as a cost-effective alternative to traditional methods. The study highlights UPT's potential as an effective way to modify the mechanical properties of wire EDMed workpieces. The impact of parameters such as the number of peening passes, feeding rate, and the type of wire EDM cut on the residual stress generated in MO40 (1.7225) alloy steel was thoroughly investigated. The experiments performed with the Taguchi method demonstrated that the UPT caused a shift in residual stress from tensile to compressive, with a maximum residual compressive stress of 1654 MPa. In the initial peening pass, an enhancement of 30%, 31%, and 48% in surface hardness values was noted for the semi-finishing, finishing, and roughing workpieces. The depth of hardness distribution reached 200 μm, while surface hardness decreased with an increased feeding rate. SEM images showed improved dislocation rearrangement due to ultrasonic vibrations, resulting in smaller surface layers, even at the nanoscale.
- 30 September 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58  (30) , 3113-3138
Stacked generalization ensemble learning strategy for multivariate prediction of delamination and maximum thrust force in composite drilling
The complexity of drilling carbon fiber reinforced polymers (CFRP) requires accurate predictive models. This study addresses the challenge using an ensemble machine learning (ML) approach with stacked generalization. The model captures the relationships between key input variables—such as graphene nanoplatelet (GNP) content, ultrasonic assistance, tool type, stacking sequence, and feed rate—and output parameters, specifically thrust force and delamination. A nested feature scoring (NFS) method was employed for importance analysis, revealing tooling type and feed rate as key features for minimizing delamination and reducing thrust force, respectively. The machinability results revealed that ultrasonic drilling lowered thrust force by improving chip evacuation and reducing fiber breakage. HSS tools with cobalt content, alongside symmetrical stacking sequence, helped to further minimize both thrust force and delamination. However, the inclusion of GNPs led to an increase in thrust force and delamination, attributed to the increased strength of the CFRP/GNP composite. The process involved meticulous training, resulting in four optimal-fit models serving as inputs for the stacked meta-model. Iterative enhancements fortified the ensemble robustness, with fine-tuning of hyperparameters through Bayesian optimization. The ensemble superiority over individual models manifested in a remarkable reduction of mean absolute error (MAE) and root mean squared error (RMSE) by up to 97% and 124% for delamination, and 205% and 154% for thrust force, compared to the best base learner. Visual and statistical assessments effectively illuminated the intricate interactions between variables in the drilling process. The methodology resulted in a highly adaptable predictive model with applications across diverse manufacturing contexts.
- 30 September 2024
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 58  (30) , 3113-3138
Stacked generalization ensemble learning strategy for multivariate prediction of delamination and maximum thrust force in composite drilling
The complexity of drilling carbon fiber reinforced polymers (CFRP) requires accurate predictive models. This study addresses the challenge using an ensemble machine learning (ML) approach with stacked generalization. The model captures the relationships between key input variables—such as graphene nanoplatelet (GNP) content, ultrasonic assistance, tool type, stacking sequence, and feed rate—and output parameters, specifically thrust force and delamination. A nested feature scoring (NFS) method was employed for importance analysis, revealing tooling type and feed rate as key features for minimizing delamination and reducing thrust force, respectively. The machinability results revealed that ultrasonic drilling lowered thrust force by improving chip evacuation and reducing fiber breakage. HSS tools with cobalt content, alongside symmetrical stacking sequence, helped to further minimize both thrust force and delamination. However, the inclusion of GNPs led to an increase in thrust force and delamination, attributed to the increased strength of the CFRP/GNP composite. The process involved meticulous training, resulting in four optimal-fit models serving as inputs for the stacked meta-model. Iterative enhancements fortified the ensemble robustness, with fine-tuning of hyperparameters through Bayesian optimization. The ensemble superiority over individual models manifested in a remarkable reduction of mean absolute error (MAE) and root mean squared error (RMSE) by up to 97% and 124% for delamination, and 205% and 154% for thrust force, compared to the best base learner. Visual and statistical assessments effectively illuminated the intricate interactions between variables in the drilling process. The methodology resulted in a highly adaptable predictive model with applications across diverse manufacturing contexts.