Yi Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yi Yang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Jun Wang
School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
1 shared publication- Min Li
Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
1 shared publication - Ping Mao
National & Local Joint Engineering Research Center for Mineral Salt Deep Utilization, Key Laboratory for Palygorskite Science and Applied Technology of Jiangsu Province, School of Chemical Engineering, Huaiyin Institute of Technology, Huaian 223003, China
1 shared publication Xinjie Yu
School of Chemical Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
1 shared publication- Yamiao Wang
Jiangsu Key Laboratory of Chemical Pollution Control and Resources Reuse, School of Environmental and Biological Engineering, Nanjing University of Science and Technology, Nanjing 210094, China
1 shared publication - Yan Jiao
Collaborative Innovation Center of Atmospheric Environment and Equipment Technology, Jiangsu Key Laboratory of Atmospheric Environment Monitoring and Pollution Control (AEMPC), Nanjing University of Information Science & Technology, Nanjing, 210044, China
1 shared publication
Latest Publications
- Open Access
- 1 January 2017
- Published by Wiley in Journal of Nanomaterials
- Vol. 2017, 1-8
Visible Light Excited Catalysis and Reusability Performances of TiO2@Pr:Y2SiO5 Upconversion Materials
To get high efficiency photodegradation on pollutants under visible light, Pr(III) doped Y2SiO5 upconversion materials and anatase TiO2 nanofilm coated Pr:Y2SiO5 composite have been prepared by using a sol-gel method. XRD and SEM test results indicated that TiO2 nanofilm was well coated on Pr:Y2SiO5 to form TiO2@Pr:Y2SiO5 composite particles with the sizes of 0.5–1.0 μm. To avoid secondary pollution resulting from incomplete recovery of catalyst particles, TiO2@Pr:Y2SiO5 was loaded on the glass fiber filters by using a dip-coating method. It is found that the catalyst particles were embedded into the carrier firmly, even after having been reused for 6 times. The luminescence intensities of TiO2@Pr:Y2SiO5 were getting down sharply with the coating contents of TiO2 increased, which was attributed to the adsorption of the luminescence by the TiO2 film in situ. As a result, TiO2@Pr:Y2SiO5 with 4% TiO2, which presented lowest luminescence intensity, showed the highest efficiency on the photodegradation of nitrobenzene wastewater. The catalysts loaded on glass fiber filters showed excellent reusability on the photodegradation of nitrobenzene and presented a photodegradation rate of 95% at the first time and up to 75.9% even after 6 times of reusing by the treatment time of 12 h.
- 1 January 2017
- Published by Wiley in Journal of Nanomaterials
- Vol. 2017, 1-8
Open AccessVisible Light Excited Catalysis and Reusability Performances of TiO2@Pr:Y2SiO5 Upconversion Materials
To get high efficiency photodegradation on pollutants under visible light, Pr(III) doped Y2SiO5 upconversion materials and anatase TiO2 nanofilm coated Pr:Y2SiO5 composite have been prepared by using a sol-gel method. XRD and SEM test results indicated that TiO2 nanofilm was well coated on Pr:Y2SiO5 to form TiO2@Pr:Y2SiO5 composite particles with the sizes of 0.5–1.0 μm. To avoid secondary pollution resulting from incomplete recovery of catalyst particles, TiO2@Pr:Y2SiO5 was loaded on the glass fiber filters by using a dip-coating method. It is found that the catalyst particles were embedded into the carrier firmly, even after having been reused for 6 times. The luminescence intensities of TiO2@Pr:Y2SiO5 were getting down sharply with the coating contents of TiO2 increased, which was attributed to the adsorption of the luminescence by the TiO2 film in situ. As a result, TiO2@Pr:Y2SiO5 with 4% TiO2, which presented lowest luminescence intensity, showed the highest efficiency on the photodegradation of nitrobenzene wastewater. The catalysts loaded on glass fiber filters showed excellent reusability on the photodegradation of nitrobenzene and presented a photodegradation rate of 95% at the first time and up to 75.9% even after 6 times of reusing by the treatment time of 12 h.
- Open Access
- 25 August 2010
- Published by Wiley in Journal of Nanomaterials
- Vol. 2011, 1-5
Effect of the Dispersibility of Nano-CuO Catalyst on Heat Releasing of AP/HTPB Propellant
Kneading time is adjusted to change the dispersibility of nano-CuO in AP/HTPB (Ammonia Perchlorate/Hydroxyl-Terminated Polybutadiene) composite propellants. Nano-CuO/AP is prepared to serve as the other dispersing method of nano-CuO, named predispersing procedure. Several kinds of heat releasing, thermal decomposition by DSC, combustion heat in oxygen environment, and explosion heat in nitrogen environment, are characterized to learn the effect of dispersibility of nano-CuO catalyst on heat releasing of propellants. With pre-dispersing procedures, thermal decomposition temperature of nano-CuO/AP and its propellant are about C and C lower than that of AP simple mixed with nano-CuO and its propellant, respectively. Comparing propellant with simple mixed nano-CuO kneading 3 hours, combustion heat and explosion heat of propellant with nano-CuO/AP increase about 1.4% and 1.7%, respectively. However, because of the breaking of nano-CuO/AP structure during kneading procedure, combustion heat and explosion heat of all the samples are decreased with the increase of kneading time after 3 hours.
- 25 August 2010
- Published by Wiley in Journal of Nanomaterials
- Vol. 2011, 1-5
Open AccessEffect of the Dispersibility of Nano-CuO Catalyst on Heat Releasing of AP/HTPB Propellant
Kneading time is adjusted to change the dispersibility of nano-CuO in AP/HTPB (Ammonia Perchlorate/Hydroxyl-Terminated Polybutadiene) composite propellants. Nano-CuO/AP is prepared to serve as the other dispersing method of nano-CuO, named predispersing procedure. Several kinds of heat releasing, thermal decomposition by DSC, combustion heat in oxygen environment, and explosion heat in nitrogen environment, are characterized to learn the effect of dispersibility of nano-CuO catalyst on heat releasing of propellants. With pre-dispersing procedures, thermal decomposition temperature of nano-CuO/AP and its propellant are about C and C lower than that of AP simple mixed with nano-CuO and its propellant, respectively. Comparing propellant with simple mixed nano-CuO kneading 3 hours, combustion heat and explosion heat of propellant with nano-CuO/AP increase about 1.4% and 1.7%, respectively. However, because of the breaking of nano-CuO/AP structure during kneading procedure, combustion heat and explosion heat of all the samples are decreased with the increase of kneading time after 3 hours.