Benoit Fournier
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Benoit Fournier has a total of 95 co-authors. Here are the top co-authors by number of shared publications:
- Josée Duchesne
Université Laval
7 shared publications L.F.M. Sanchez
3 shared publicationsM. Jolin
3 shared publicationsAbdelgadir Abbas
Amec Americas, Calgary, Alberta, Canada
2 shared publications- Abdul Ghani Razaqpur
Department of Civil Engineering, McMaster University, Hamilton, ON L8S 4L7, Canada
2 shared publications - António Santos Silva
Materials Department, National Laboratory for Civil Engineering, 1700-066 Lisbon, Portugal
2 shared publications
Latest Publications
- Open Access
- 4 September 2026
- Published by Elsevier in SSRN Electronic Journal
Long-term effectiveness of hydrophobic penetrating sealers in counteracting alkali–silica reaction and chloride ingress in highway median barrier sections exposed to wetting and drying, freezing and thawing, and de-icing salts
There is a range of opinions among materials suppliers and engineers regarding the longevity of hydrophobic surface treatments for protecting concrete elements in outdoor conditions, due to a lack of field data. This paper presents a follow-up study on the use of silane/siloxane-based penetrating sealers to mitigate/control ASR in highway median barrier sections in the Quebec City area and their impact on chloride ingress. The original field study was conducted in the early 1990’s. The aim of the present study was to assess the condition of the median barrier sections approximately 25 years after treatment. This was achieved by assessing their superficial condition with a semi-automated image analysis procedure and their internal damage by the Damage Rating Index and polarising microscopy. Furthermore, a qualitative assessment of chloride ingress was performed with a μXRF device. The results indicate that all tested penetrating sealers have been effective in mitigating/controlling ASR over that 25-year period, demonstrating convincingly the potential long-term in situ durability of such hydrophobic surface treatment. The semi-automated map cracking assessment tool by image analysis of inspection pictures yielded promising results, which should prompt further development/testing. The qualitative chloride assessment suggests that one silane application has provided a chloride protection equal to approximately 15 mm of concrete cover to that ASR-affected barrier section, over the 25-year period, which can be related to a combination of the hydrophobic effect of the sealer and the reduction of cracking induced by ASR.
- 4 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessLong-term effectiveness of hydrophobic penetrating sealers in counteracting alkali–silica reaction and chloride ingress in highway median barrier sections exposed to wetting and drying, freezing and thawing, and de-icing salts
There is a range of opinions among materials suppliers and engineers regarding the longevity of hydrophobic surface treatments for protecting concrete elements in outdoor conditions, due to a lack of field data. This paper presents a follow-up study on the use of silane/siloxane-based penetrating sealers to mitigate/control ASR in highway median barrier sections in the Quebec City area and their impact on chloride ingress. The original field study was conducted in the early 1990’s. The aim of the present study was to assess the condition of the median barrier sections approximately 25 years after treatment. This was achieved by assessing their superficial condition with a semi-automated image analysis procedure and their internal damage by the Damage Rating Index and polarising microscopy. Furthermore, a qualitative assessment of chloride ingress was performed with a μXRF device. The results indicate that all tested penetrating sealers have been effective in mitigating/controlling ASR over that 25-year period, demonstrating convincingly the potential long-term in situ durability of such hydrophobic surface treatment. The semi-automated map cracking assessment tool by image analysis of inspection pictures yielded promising results, which should prompt further development/testing. The qualitative chloride assessment suggests that one silane application has provided a chloride protection equal to approximately 15 mm of concrete cover to that ASR-affected barrier section, over the 25-year period, which can be related to a combination of the hydrophobic effect of the sealer and the reduction of cracking induced by ASR.
- 1 September 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Cold Regions Engineering
- Vol. 40 (3) , 04026049
Monte Carlo Modeling of Asphalt Surface Wear under Studded-Tire Traffic
In this paper, the evolution of surface damage of asphalt pavements under studded tire traffic is examined using a combined experimental and stochastic modeling approach. Laboratory tests on six asphalt mixtures were integrated into a Monte Carlo framework that represents rutting wear as the cumulative effect of random stud impacts. The introduced model accurately captures the transition from the initial phase to the steady linear rutting regime and exhibits consistency with the experimental results. A strong linear relationship was identified between the stochastic detachment parameter Λ and the laboratory rutting rate κ lab , as well as with the abrasion resistance AbrA, confirming the model’s ability to reproduce measurable material responses. By linking key mixture parameters to probabilistic descriptions of surface deterioration, the proposed framework provides a predictive tool for assessing and guiding the design of more durable pavements in cold climate regions.
- 1 September 2026
- Published by American Society of Civil Engineers (ASCE) in Journal of Cold Regions Engineering
- Vol. 40 (3) , 04026049
Monte Carlo Modeling of Asphalt Surface Wear under Studded-Tire Traffic
In this paper, the evolution of surface damage of asphalt pavements under studded tire traffic is examined using a combined experimental and stochastic modeling approach. Laboratory tests on six asphalt mixtures were integrated into a Monte Carlo framework that represents rutting wear as the cumulative effect of random stud impacts. The introduced model accurately captures the transition from the initial phase to the steady linear rutting regime and exhibits consistency with the experimental results. A strong linear relationship was identified between the stochastic detachment parameter Λ and the laboratory rutting rate κ lab , as well as with the abrasion resistance AbrA, confirming the model’s ability to reproduce measurable material responses. By linking key mixture parameters to probabilistic descriptions of surface deterioration, the proposed framework provides a predictive tool for assessing and guiding the design of more durable pavements in cold climate regions.
- Open Access
- 30 March 2026
- Published by Elsevier in SSRN Electronic Journal
Impact of sample preparation on XRD quantification of sulfides and XPS identification of oxidation products in concrete aggregates
The accurate quantification of sulfide minerals in rock aggregates is critical for assessing the long-term durability of concrete structures. However, establishing an optimal sample preparation protocol remains challenging, as mechanical processing can introduce significant methodological uncertainties. This study evaluates the impact of milling methods (dry vs wet) and duration (2, 5, and 10 minutes) on the quantification of pyrite and pyrrhotite using X-ray diffraction (XRD), Electron Probe Microanalysis (EPMA), and X-ray Photoelectron Spectroscopy (XPS).Results show that wet milling improves analytical reliability compared to dry milling by reducing variability and enhancing powder homogeneity. Although longer milling durations improve reproducibility, they also increase the susceptibility of sulfides, particularly pyrrhotite, to mechanical stress, leading to selective degradation and underestimation. Textural analysis reveals that sulfide liberation is strongly controlled by the host rock matrix. Fine-grained matrices with disseminated sulfides, such as the mudslate mainly composed of quartz and muscovite, achieve homogeneity more efficiently due to weaker intergranular bonding. In contrast, coarse sulfide clusters within harder silicate matrices, exemplified by the maskimo (MSK) aggregate, exhibit greater variability.Furthermore, XPS data show that pyrrhotite undergoes rapid surface oxidation even before preparation, with an inferred surface recession rate of 0.5 nm day−1, potentially causing systematic underestimation of its true abundance. These findings suggest that conventional XRD analysis of pyrrhotite-bearing aggregates should be regarded as providing a lower-bound estimate, highlighting the need for a multi-technique framework to ensure reliable assessment of potentially reactive sulfides in concrete environments.
- 30 March 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessImpact of sample preparation on XRD quantification of sulfides and XPS identification of oxidation products in concrete aggregates
The accurate quantification of sulfide minerals in rock aggregates is critical for assessing the long-term durability of concrete structures. However, establishing an optimal sample preparation protocol remains challenging, as mechanical processing can introduce significant methodological uncertainties. This study evaluates the impact of milling methods (dry vs wet) and duration (2, 5, and 10 minutes) on the quantification of pyrite and pyrrhotite using X-ray diffraction (XRD), Electron Probe Microanalysis (EPMA), and X-ray Photoelectron Spectroscopy (XPS).Results show that wet milling improves analytical reliability compared to dry milling by reducing variability and enhancing powder homogeneity. Although longer milling durations improve reproducibility, they also increase the susceptibility of sulfides, particularly pyrrhotite, to mechanical stress, leading to selective degradation and underestimation. Textural analysis reveals that sulfide liberation is strongly controlled by the host rock matrix. Fine-grained matrices with disseminated sulfides, such as the mudslate mainly composed of quartz and muscovite, achieve homogeneity more efficiently due to weaker intergranular bonding. In contrast, coarse sulfide clusters within harder silicate matrices, exemplified by the maskimo (MSK) aggregate, exhibit greater variability.Furthermore, XPS data show that pyrrhotite undergoes rapid surface oxidation even before preparation, with an inferred surface recession rate of 0.5 nm day−1, potentially causing systematic underestimation of its true abundance. These findings suggest that conventional XRD analysis of pyrrhotite-bearing aggregates should be regarded as providing a lower-bound estimate, highlighting the need for a multi-technique framework to ensure reliable assessment of potentially reactive sulfides in concrete environments.
- Open Access
- 17 February 2026
- Published by Elsevier in SSRN Electronic Journal
Characterization of aggregate reactivity to alkali-silica reaction through diffusion and dissolution properties
Transport and dissolution mechanisms govern the Alkali-Silica Reaction (ASR) sequences. Ion diffusion by concentration gradient triggers dissolution, which leads to the precipitation of new phases, initiating pressures that cause the aggregate cracking. Quantifying these transport and kinetic properties is therefore essential to assess aggregate reactivity and to support predictive modelling. An experimental campaign for the characterization of diffusion coefficients and dissolution rates has been conducted. Four aggregates, representative of various kinetics and level of expansion in similar concrete conditions, were selected: greywacke, limestone, quartzitic sandstone and a non-reactive quartzite. Diffusion coefficients were measured using X-ray spectroscopy. Iodide ions (1M I-) were used as a conservative tracer. Both parallel- and perpendicular-to bedding diffusion coefficients were measured. For dissolution properties assessment, aggregates were immersed in a basic solution to promote the degradation of the silica reactive microstructure. Two particle size fractions for each aggregate (0.5-1 mm and 1-2 mm) and three temperatures (25, 40 and 60°C) were considered. The study displays the diffusion parameters and dissolution rate coefficients for the four aggregates. The values of effective diffusion coefficient determined lie within a wide range, from 10-11 to 10-15 m²/s, which strongly influence the reaction sequence according to aggregate nature. The dissolution rate values are in the range from 10-11 to 10-13 mol/(m².s). The combined analysis demonstrates that diffusion and dissolution processes control ASR advancement by governing the characteristic time of aggregate degradation. The data provided constitute valuable input for improving the evaluation of ASR kinetics through predictive modelling.
- 17 February 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCharacterization of aggregate reactivity to alkali-silica reaction through diffusion and dissolution properties
Transport and dissolution mechanisms govern the Alkali-Silica Reaction (ASR) sequences. Ion diffusion by concentration gradient triggers dissolution, which leads to the precipitation of new phases, initiating pressures that cause the aggregate cracking. Quantifying these transport and kinetic properties is therefore essential to assess aggregate reactivity and to support predictive modelling. An experimental campaign for the characterization of diffusion coefficients and dissolution rates has been conducted. Four aggregates, representative of various kinetics and level of expansion in similar concrete conditions, were selected: greywacke, limestone, quartzitic sandstone and a non-reactive quartzite. Diffusion coefficients were measured using X-ray spectroscopy. Iodide ions (1M I-) were used as a conservative tracer. Both parallel- and perpendicular-to bedding diffusion coefficients were measured. For dissolution properties assessment, aggregates were immersed in a basic solution to promote the degradation of the silica reactive microstructure. Two particle size fractions for each aggregate (0.5-1 mm and 1-2 mm) and three temperatures (25, 40 and 60°C) were considered. The study displays the diffusion parameters and dissolution rate coefficients for the four aggregates. The values of effective diffusion coefficient determined lie within a wide range, from 10-11 to 10-15 m²/s, which strongly influence the reaction sequence according to aggregate nature. The dissolution rate values are in the range from 10-11 to 10-13 mol/(m².s). The combined analysis demonstrates that diffusion and dissolution processes control ASR advancement by governing the characteristic time of aggregate degradation. The data provided constitute valuable input for improving the evaluation of ASR kinetics through predictive modelling.
- Open Access
- 11 August 2025
- Published by Elsevier in Cement and Concrete Research
- Vol. 198
Understanding long-term ASR expansion in glass powder ternary concrete blends through accelerated solubility test
- 11 August 2025
- Published by Elsevier in Cement and Concrete Research
- Vol. 198
Open AccessUnderstanding long-term ASR expansion in glass powder ternary concrete blends through accelerated solubility test
- Open Access
- 14 April 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 476
Microstructural and chemical characterization of glass powder and silica fume ternary concrete after seven years of alkali-silica reaction expansion exposure
- 14 April 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 476
Open AccessMicrostructural and chemical characterization of glass powder and silica fume ternary concrete after seven years of alkali-silica reaction expansion exposure
- 1 June 2022
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Construction Materials
- Vol. 175 (3) , 125-136
Long-term alkali–silica mitigation of high-alkali concrete with cement replacements
In this study, the impact of high-alkali Portland cements on the prescribed level of supplementary cementitious materials (SCMs) required in the Canadian standard for alkali–silica reaction mitigation was evaluated. On the basis of the results, for concretes containing aggregates exhibiting moderate reactivity, the maximum allowable cement alkali limit was increased from 1.00 to 1.15%. For all the levels of aggregate reactivity, cement alkali contents could be allowed up to 1.25% provided the recommended level of mitigation by SCMs was increased. In the initial laboratory study, mortar bars and concrete prisms were cast and monitored using two different reactive aggregates and recommended levels of fly ash and slag. For the concrete prism tests, the alkali contents of cements were increased to 1.25%, as per the standard, or were increased by 0.25%. Instrumented outdoor exposure concrete blocks, along with additional concrete prisms stored at different temperatures, were cast from numerous mixtures prepared with cement alkali equivalents ranging up to 1.22%. This paper reports on the long-term performance of prisms and concrete blocks after 12 and 27 years. The performance of the outdoor blocks is also compared with the predicted performance based on the results of accelerated mortar bar and concrete prism test.
- 1 June 2022
- Published by Emerald Publishing in Proceedings of the Institution of Civil Engineers - Construction Materials
- Vol. 175 (3) , 125-136
Long-term alkali–silica mitigation of high-alkali concrete with cement replacements
In this study, the impact of high-alkali Portland cements on the prescribed level of supplementary cementitious materials (SCMs) required in the Canadian standard for alkali–silica reaction mitigation was evaluated. On the basis of the results, for concretes containing aggregates exhibiting moderate reactivity, the maximum allowable cement alkali limit was increased from 1.00 to 1.15%. For all the levels of aggregate reactivity, cement alkali contents could be allowed up to 1.25% provided the recommended level of mitigation by SCMs was increased. In the initial laboratory study, mortar bars and concrete prisms were cast and monitored using two different reactive aggregates and recommended levels of fly ash and slag. For the concrete prism tests, the alkali contents of cements were increased to 1.25%, as per the standard, or were increased by 0.25%. Instrumented outdoor exposure concrete blocks, along with additional concrete prisms stored at different temperatures, were cast from numerous mixtures prepared with cement alkali equivalents ranging up to 1.22%. This paper reports on the long-term performance of prisms and concrete blocks after 12 and 27 years. The performance of the outdoor blocks is also compared with the predicted performance based on the results of accelerated mortar bar and concrete prism test.
- Open Access
- 9 May 2022
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 72 (346) , e278
Alkali-silica reaction in volcanic rocks: a worldwide comparative approach
The potential alkali-silica reactivity (ASR) of volcanic aggregates, especially basalts, remains a source of debate in the scientific community. When evaluating the potentially deleterious character of this type of aggregate, different laboratory testing methods may produce contradictory data; this is particularly evident when using the accelerated mortar bar test (AMBT). In order to better understand such discrepancies, this study applied several methods of characterizing potential aggregate alkali reactivity, including the accelerated mortar bar test (AMBT), petrographic characterization, and the concrete prism test (CPT). Moreover, this study assessed volcanic aggregate samples from sites around the world, including the Azores, Brazil, Canada, the Canary and Hawaiian Islands, Iceland, Japan, Mozambique, New Zealand, Norway, and Turkey. The results obtained contribute to accurately assessing the potential alkali reactivity of volcanic aggregates and enhance the understanding of their different behaviours.
- 9 May 2022
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 72 (346) , e278
Open AccessAlkali-silica reaction in volcanic rocks: a worldwide comparative approach
The potential alkali-silica reactivity (ASR) of volcanic aggregates, especially basalts, remains a source of debate in the scientific community. When evaluating the potentially deleterious character of this type of aggregate, different laboratory testing methods may produce contradictory data; this is particularly evident when using the accelerated mortar bar test (AMBT). In order to better understand such discrepancies, this study applied several methods of characterizing potential aggregate alkali reactivity, including the accelerated mortar bar test (AMBT), petrographic characterization, and the concrete prism test (CPT). Moreover, this study assessed volcanic aggregate samples from sites around the world, including the Azores, Brazil, Canada, the Canary and Hawaiian Islands, Iceland, Japan, Mozambique, New Zealand, Norway, and Turkey. The results obtained contribute to accurately assessing the potential alkali reactivity of volcanic aggregates and enhance the understanding of their different behaviours.
- Open Access
- 29 April 2022
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 72 (346) , e279
RILEM TC 258-AAA Round Robin Test: Alkali release from aggregates and petrographic analysis. Critical review of the test method AAR-8
To create an international recommendation concerning the release of alkalis, test method AAR-8 was developed within the scope of RILEM TC 258-AAA activities. The first round robin test was performed using five aggregate types, and further investigation was conducted as RRT2, leading to the final version of the AAR-8 recommendation. Five aggregates with different mineralogies and origins were immersed in specific volumes of NaOH or KOH solutions with excess calcium hydroxide maintained 38 °C and 60 °C respectively. Samples of the immersion test solution were removed at intervals of 2, 6, 13, 26, and 52 weeks by pipetting and chemically analyzed for NaOH or KOH test solutions. The amount of alkali released was expressed in grams of Na2O, K2O, and Na2Oe per kilogram of the respective aggregate. The results obtained are presented. Based on the data, several changes to the original version of the test method are proposed.
- 29 April 2022
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 72 (346) , e279
Open AccessRILEM TC 258-AAA Round Robin Test: Alkali release from aggregates and petrographic analysis. Critical review of the test method AAR-8
To create an international recommendation concerning the release of alkalis, test method AAR-8 was developed within the scope of RILEM TC 258-AAA activities. The first round robin test was performed using five aggregate types, and further investigation was conducted as RRT2, leading to the final version of the AAR-8 recommendation. Five aggregates with different mineralogies and origins were immersed in specific volumes of NaOH or KOH solutions with excess calcium hydroxide maintained 38 °C and 60 °C respectively. Samples of the immersion test solution were removed at intervals of 2, 6, 13, 26, and 52 weeks by pipetting and chemically analyzed for NaOH or KOH test solutions. The amount of alkali released was expressed in grams of Na2O, K2O, and Na2Oe per kilogram of the respective aggregate. The results obtained are presented. Based on the data, several changes to the original version of the test method are proposed.