Loleï Khoun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Loleï Khoun has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Pascal Hubert
Department of Mechanical Engineering, McGill University, Canada
5 shared publications- Pascal Hubert
McGill University
5 shared publications - Leonardo Barcenas
Department of Mechanical and Aerospace Engineering, Carleton University, Ottawa, ON, Canada
2 shared publications Andrew Johnston
1 shared publication- Behnam Ashrafi
National Research Council Canada
1 shared publication - Benoit Simard
National Research Council Canada
1 shared publication
Latest Publications
- Open Access
- 4 September 2025
- Published by Elsevier in Composites Communications
- Vol. 59
A thermochemical and rheological model incorporating inhibition time for highly reactive polyester resins in liquid moulding processes
- 4 September 2025
- Published by Elsevier in Composites Communications
- Vol. 59
Open AccessA thermochemical and rheological model incorporating inhibition time for highly reactive polyester resins in liquid moulding processes
- 8 September 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (11) , 6146-6159
Manufacturing of bio‐based thermoplastic composites using industrial process for high‐volume applications
The use of high strength‐to‐weight ratio materials in automotive component is a solution to reduce fuel consumption and decrease greenhouse gases emissions. Fiber reinforced composite materials are believed to enable weight saving that cannot be achieved with metals while meeting component mechanical requirements. Moreover, the use of renewable bio‐based composites is seen as a key aspect to further address the reduction of greenhouse gases emission. However, composite manufacturing process must meet short cycle time, performance, and cost targeted by the transportation industry in order to be considered as replacement materials. This article investigates the use of an industrial compression—direct long fiber thermoplastic (D‐LFT) process line to manufacture cellulose reinforced bio‐based polyamide parts in order to increase the penetration of sustainable materials in the transportation sectors. Process evaluation and composite performance were first carried out on a simple 2D geometry. Then the use of 100% bio‐sourced materials with the high‐throughput D‐LFT process was validated with the manufacturing of an automotive composite seat pan demonstrator. Bio‐based composite parts were successfully manufactured. Tensile properties in the range of glass fiber reinforced polypropylene composites traditionally used with the D‐LFT process were measured, validating the potential of cellulose–biopolyamide composite materials for industrial applications.
- 8 September 2021
- Published by Wiley in Polymer Composites
- Vol. 42 (11) , 6146-6159
Manufacturing of bio‐based thermoplastic composites using industrial process for high‐volume applications
The use of high strength‐to‐weight ratio materials in automotive component is a solution to reduce fuel consumption and decrease greenhouse gases emissions. Fiber reinforced composite materials are believed to enable weight saving that cannot be achieved with metals while meeting component mechanical requirements. Moreover, the use of renewable bio‐based composites is seen as a key aspect to further address the reduction of greenhouse gases emission. However, composite manufacturing process must meet short cycle time, performance, and cost targeted by the transportation industry in order to be considered as replacement materials. This article investigates the use of an industrial compression—direct long fiber thermoplastic (D‐LFT) process line to manufacture cellulose reinforced bio‐based polyamide parts in order to increase the penetration of sustainable materials in the transportation sectors. Process evaluation and composite performance were first carried out on a simple 2D geometry. Then the use of 100% bio‐sourced materials with the high‐throughput D‐LFT process was validated with the manufacturing of an automotive composite seat pan demonstrator. Bio‐based composite parts were successfully manufactured. Tensile properties in the range of glass fiber reinforced polypropylene composites traditionally used with the D‐LFT process were measured, validating the potential of cellulose–biopolyamide composite materials for industrial applications.
- 17 September 2013
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Carded Recycled Carbon Fiber Mats for the Production of Thermoset Composites via Infusion/Compression Molding
The use of carbon fiber reinforced thermoset composites has doubled in the last decade raising questions about the waste generated from manufacturing and at end-of-life, especially in the aircraft industry. In this study, 2.5 cm long carbon fibers were recovered from thermoset composite waste using a commercial scale pyrolysis process. Scanning electron microscopy, density measurements, single filament tensile testing as well as micro-droplet testing were performed to characterize the morphology, mechanical properties, and surface adhesion of the fibers. The recycled fibers appeared to be mostly undamaged and clean, exhibiting comparable mechanical properties to virgin carbon fibers. A carding process followed by an ultrasound treatment produced randomly aligned recycled fiber mats. These mats were used to fabricate composite plates, with fiber volume fractions up to 40 %, by infusion / compression molding. The mechanical properties of the plates were evaluated by tensile and flexural testing, and were found to be comparable to an equivalent containing virgin carbon fibers.
- 17 September 2013
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Carded Recycled Carbon Fiber Mats for the Production of Thermoset Composites via Infusion/Compression Molding
The use of carbon fiber reinforced thermoset composites has doubled in the last decade raising questions about the waste generated from manufacturing and at end-of-life, especially in the aircraft industry. In this study, 2.5 cm long carbon fibers were recovered from thermoset composite waste using a commercial scale pyrolysis process. Scanning electron microscopy, density measurements, single filament tensile testing as well as micro-droplet testing were performed to characterize the morphology, mechanical properties, and surface adhesion of the fibers. The recycled fibers appeared to be mostly undamaged and clean, exhibiting comparable mechanical properties to virgin carbon fibers. A carding process followed by an ultrasound treatment produced randomly aligned recycled fiber mats. These mats were used to fabricate composite plates, with fiber volume fractions up to 40 %, by infusion / compression molding. The mechanical properties of the plates were evaluated by tensile and flexural testing, and were found to be comparable to an equivalent containing virgin carbon fibers.
- 3 June 2013
- Published by IOP Publishing in Nanotechnology
- Vol. 24 (26) , 265701
Influence of the reaction stoichiometry on the mechanical and thermal properties of SWCNT-modified epoxy composites
Previous studies suggest that carbon nanotubes (CNTs) have a considerable influence on the curing behavior and crosslink density of epoxy resins. This invariably has an important effect on different thermal and mechanical properties of the epoxy network. This work focuses on the important role of the epoxy/hardener mixing ratio on the mechanical and thermal properties of a high temperature aerospace-grade epoxy (MY0510 Araldite as an epoxy and 4,4'-diaminodiphenylsulfone as an aromatic hardener) modified with single-walled carbon nanotubes (SWCNTs). The effects of three different stoichiometries (stoichiometric and off-stoichiometric) on various mechanical and thermal properties (fracture toughness, tensile properties, glass transition temperature) of the epoxy resin and its SWCNT-modified composites were obtained. The results were also supported by Raman spectroscopy and scanning electron microscopy (SEM). For the neat resin, it was found that an epoxy/hardener molar ratio of 1:0.8 provides the best overall properties. In contrast, the pattern in property changes with the reaction stoichiometry was considerably different for composites reinforced with unfunctionalized SWCNTs and reduced SWCNTs. A comparison among composites suggests that a 1:1 molar ratio considerably outperforms the other two ratios examined in this work (1:0.8 and 1:1.1). This composition at 0.2 wt% SWCNT loading provides the highest overall mechanical properties by improving fracture toughness, ultimate tensile strength and ultimate tensile strain of the epoxy resin by 40%, 34%, 54%, respectively.
- 3 June 2013
- Published by IOP Publishing in Nanotechnology
- Vol. 24 (26) , 265701
Influence of the reaction stoichiometry on the mechanical and thermal properties of SWCNT-modified epoxy composites
Previous studies suggest that carbon nanotubes (CNTs) have a considerable influence on the curing behavior and crosslink density of epoxy resins. This invariably has an important effect on different thermal and mechanical properties of the epoxy network. This work focuses on the important role of the epoxy/hardener mixing ratio on the mechanical and thermal properties of a high temperature aerospace-grade epoxy (MY0510 Araldite as an epoxy and 4,4'-diaminodiphenylsulfone as an aromatic hardener) modified with single-walled carbon nanotubes (SWCNTs). The effects of three different stoichiometries (stoichiometric and off-stoichiometric) on various mechanical and thermal properties (fracture toughness, tensile properties, glass transition temperature) of the epoxy resin and its SWCNT-modified composites were obtained. The results were also supported by Raman spectroscopy and scanning electron microscopy (SEM). For the neat resin, it was found that an epoxy/hardener molar ratio of 1:0.8 provides the best overall properties. In contrast, the pattern in property changes with the reaction stoichiometry was considerably different for composites reinforced with unfunctionalized SWCNTs and reduced SWCNTs. A comparison among composites suggests that a 1:1 molar ratio considerably outperforms the other two ratios examined in this work (1:0.8 and 1:1.1). This composition at 0.2 wt% SWCNT loading provides the highest overall mechanical properties by improving fracture toughness, ultimate tensile strength and ultimate tensile strain of the epoxy resin by 40%, 34%, 54%, respectively.
- 20 February 2012
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 46 (25) , 3121-3136
Thermo-mechanical properties of 5-harness satin fabric composites
The use of woven textile reinforcements in composite structures increased significantly in the past decades due to their interesting properties over unidirectional fibres. Therefore, the prediction of the thermo-mechanical properties of woven fabric composites is essential from a design and manufacturing standpoint. A micromechanical approach based on finite element method that utilizes three-dimensional unit cell was applied to predict the effective properties of a periodic woven fabric composite material. Using the resin processing properties models such as cure kinetics, shrinkage, glass transition temperature and elastic modulus models, the development of the periodic woven fabric composite material thermo-mechanical properties, as the cure progresses was predicted. The residual strains and stresses generated in the composite unit cell during the cure were also predicted and linked with the development of the material properties. The effective properties of the cured woven fabric composite material were compared to the one of an equivalent cross-ply composite material to verify the validity of neglecting the fibre waviness while modelling woven fabric composite.
- 20 February 2012
- Published by SAGE Publications in Journal of Composite Materials
- Vol. 46 (25) , 3121-3136
Thermo-mechanical properties of 5-harness satin fabric composites
The use of woven textile reinforcements in composite structures increased significantly in the past decades due to their interesting properties over unidirectional fibres. Therefore, the prediction of the thermo-mechanical properties of woven fabric composites is essential from a design and manufacturing standpoint. A micromechanical approach based on finite element method that utilizes three-dimensional unit cell was applied to predict the effective properties of a periodic woven fabric composite material. Using the resin processing properties models such as cure kinetics, shrinkage, glass transition temperature and elastic modulus models, the development of the periodic woven fabric composite material thermo-mechanical properties, as the cure progresses was predicted. The residual strains and stresses generated in the composite unit cell during the cure were also predicted and linked with the development of the material properties. The effective properties of the cured woven fabric composite material were compared to the one of an equivalent cross-ply composite material to verify the validity of neglecting the fibre waviness while modelling woven fabric composite.
- 4 August 2011
- Published by Wiley in Polymer Composites
- Vol. 32 (9) , 1473-1480
Relation between volumetric changes of unsaturated polyester resin and surface finish quality of fiberglass/unsaturated polyester composite panels
Resin dimensional changes, including cure shrinkage and thermal expansion, highly influence the surface finish quality of composite parts. Low profile additives (LPA) are commonly incorporated in unsaturated polyester (UP) resins to compensate for resin shrinkage and obtain a high quality surface finish. In this study, the dimensional change of an UP resin with different LPA contents was characterized. Both resin cure shrinkage and resin thermal expansion were measured. A simple methodology was then developed to estimate the surface finish quality of panels, manufactured by resin transfer molding (RTM), based on the prediction of part thickness variation during the process. Results show good agreement with the experimental investigations. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers
- 4 August 2011
- Published by Wiley in Polymer Composites
- Vol. 32 (9) , 1473-1480
Relation between volumetric changes of unsaturated polyester resin and surface finish quality of fiberglass/unsaturated polyester composite panels
Resin dimensional changes, including cure shrinkage and thermal expansion, highly influence the surface finish quality of composite parts. Low profile additives (LPA) are commonly incorporated in unsaturated polyester (UP) resins to compensate for resin shrinkage and obtain a high quality surface finish. In this study, the dimensional change of an UP resin with different LPA contents was characterized. Both resin cure shrinkage and resin thermal expansion were measured. A simple methodology was then developed to estimate the surface finish quality of panels, manufactured by resin transfer molding (RTM), based on the prediction of part thickness variation during the process. Results show good agreement with the experimental investigations. POLYM. COMPOS., 2011. © 2011 Society of Plastics Engineers
- 1 May 2011
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 30 (9) , 815-823
Effect of low-profile additives on thermo-mechanical properties of glass fiber-reinforced unsaturated polyester composites
Low profile additives (LPA) are thermoplastics particles incorporated into unsaturated polyester (UP) resin in order to improve the surface finish of fiber glass/UP composites by shrinkage compensation. They are widely used in automotive applications where high-quality surface finish is required. In this article, the effect of low-profile additives on the thermo-mechanical properties of resin transfer molded fiber glass/UP panels is investigated. A combination of poly vinyl-acetate and poly methyl-methacrylate additives was tested with three concentrations (0%, 10%, and 40%). The flexural and shear properties were measured by three-point bending and short-beam tests. Thermo-mechanical and dynamic mechanical analyses were performed to measure the coefficient of thermal expansion and the glass transition temperature. The mechanical properties as well as the coefficient of thermal expansion were reduced upon addition of low-profile additives, whereas the glass transition temperature was improved with the content of low profile additives due to a better compatibility of the LPA/UP system.
- 1 May 2011
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 30 (9) , 815-823
Effect of low-profile additives on thermo-mechanical properties of glass fiber-reinforced unsaturated polyester composites
Low profile additives (LPA) are thermoplastics particles incorporated into unsaturated polyester (UP) resin in order to improve the surface finish of fiber glass/UP composites by shrinkage compensation. They are widely used in automotive applications where high-quality surface finish is required. In this article, the effect of low-profile additives on the thermo-mechanical properties of resin transfer molded fiber glass/UP panels is investigated. A combination of poly vinyl-acetate and poly methyl-methacrylate additives was tested with three concentrations (0%, 10%, and 40%). The flexural and shear properties were measured by three-point bending and short-beam tests. Thermo-mechanical and dynamic mechanical analyses were performed to measure the coefficient of thermal expansion and the glass transition temperature. The mechanical properties as well as the coefficient of thermal expansion were reduced upon addition of low-profile additives, whereas the glass transition temperature was improved with the content of low profile additives due to a better compatibility of the LPA/UP system.
- 1 March 2011
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 42 (3) , 274-282
Investigation of process-induced strains development by fibre Bragg grating sensors in resin transfer moulded composites
- 1 March 2011
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 42 (3) , 274-282
Investigation of process-induced strains development by fibre Bragg grating sensors in resin transfer moulded composites
- 19 August 2010
- Published by Wiley in Polymer Composites
- Vol. 31 (9) , 1603-1610
Cure shrinkage characterization of an epoxy resin system by two in situ measurement methods
Dimensional accuracy of composites manufacturing is a major issue for part producers, especially when tight tolerances are required. One of the main causes of dimensional variations is the resin volumetric changes during the cure. In this article, volumetric cure shrinkage of a one part epoxy system was characterized using two different methods. First, a modified rheology method was used to measure the volumetric cure shrinkage after the gel point. Second, a gravimetric method measured the shrinkage over the entire cure. A linear relationship between the volumetric cure shrinkage and the degree‐of‐cure was deduced from the results and the resin cure kinetic models. Results show a good agreement between the two techniques. POLYM. COMPOS., 31:1603–1610, 2010. © 2009 Society of Plastics Engineers
- 19 August 2010
- Published by Wiley in Polymer Composites
- Vol. 31 (9) , 1603-1610
Cure shrinkage characterization of an epoxy resin system by two in situ measurement methods
Dimensional accuracy of composites manufacturing is a major issue for part producers, especially when tight tolerances are required. One of the main causes of dimensional variations is the resin volumetric changes during the cure. In this article, volumetric cure shrinkage of a one part epoxy system was characterized using two different methods. First, a modified rheology method was used to measure the volumetric cure shrinkage after the gel point. Second, a gravimetric method measured the shrinkage over the entire cure. A linear relationship between the volumetric cure shrinkage and the degree‐of‐cure was deduced from the results and the resin cure kinetic models. Results show a good agreement between the two techniques. POLYM. COMPOS., 31:1603–1610, 2010. © 2009 Society of Plastics Engineers