Akhmad Zidni Hudaya
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Akhmad Zidni Hudaya has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Okto Dinaryanto
Institut Teknologi Dirgantara Adisutjipto
4 shared publications - Deendarlianto Deendarlianto
Universitas Gadjah Mada
3 shared publications - Akmal Irfan Majid
Centre For Energy Studies Universitas Gadjah Mada Kabupaten Sleman, Daerah Istimewa Yogyakarta Indonesia
2 shared publications - Hadiyan Yusuf Kuntoro
Fine Art Department, Faculty of Visual Arts, Institut Seni Indonesia Yogyakarta
2 shared publications Indarto
2 shared publicationsAdhika Widyaparaga
1 shared publication
Latest Publications
- Open Access
- 31 December 2024
- Published by Universitas Muria Kudus in Journal of Industrial Engineering and Technology
- Vol. 5 (1) , 98-107
SIMULASI ALIRAN DUA FASA STRATIFIED AIR - UDARA PADA PIPA HORIZONTAL DENGAN PENDEKATAN VOLUME OF FLUID (VOF)
The flow conditions inside a pipe can involve two different densities or commonly known as two-phase flow. Besides density differences, fluctuations also affect the flow patterns of two-phase flow. These fluctuations result in various flow patterns, including the stratified flow pattern often utilized in fluid industries and the slugging flow pattern, which is generally avoided. Therefore, understanding the characteristics of these flow patterns is crucial, and Computational Fluid Dynamics (CFD) simulation methods are employed for this purpose. In the simulation model used, Volume Of Fluid (VOF) is employed with turbulent k-ε flow in a 19 mm diameter, 9 m long T-shaped pipe with a separating plate between the inlet of water and air. This setup yields various flow patterns such as Stratified ripple, Stratified wave, roll wave, and pseudo slug. At low pressure differences and velocities of JL = 0.025 m/s and JG = 1.88 m/s, a smooth stratified interface profile is observed, clearly separating the phases of water flowing continuously at the bottom and gas flowing at the top due to density differences, without any waves. As the velocities are increased to JL = 0.040 m/s and JG = 5.246 m/s, a ripple wave flow pattern occurs, characterized by small waves accompanied by long waves. Furthermore, increasing JL while decreasing JG to JL = 0.050 m/s and JG = 4.140 m/s leads to the formation of a stratified roll flow pattern, marked by long rolls, while pseudo slug flow occurs at JG = 5.246 m/s and JL = 0.076 m/s. This happens due to the increased velocity of the water phase causing the gas phase to become unstable, forming bubbles within the liquid
- 31 December 2024
- Published by Universitas Muria Kudus in Journal of Industrial Engineering and Technology
- Vol. 5 (1) , 98-107
Open AccessSIMULASI ALIRAN DUA FASA STRATIFIED AIR - UDARA PADA PIPA HORIZONTAL DENGAN PENDEKATAN VOLUME OF FLUID (VOF)
The flow conditions inside a pipe can involve two different densities or commonly known as two-phase flow. Besides density differences, fluctuations also affect the flow patterns of two-phase flow. These fluctuations result in various flow patterns, including the stratified flow pattern often utilized in fluid industries and the slugging flow pattern, which is generally avoided. Therefore, understanding the characteristics of these flow patterns is crucial, and Computational Fluid Dynamics (CFD) simulation methods are employed for this purpose. In the simulation model used, Volume Of Fluid (VOF) is employed with turbulent k-ε flow in a 19 mm diameter, 9 m long T-shaped pipe with a separating plate between the inlet of water and air. This setup yields various flow patterns such as Stratified ripple, Stratified wave, roll wave, and pseudo slug. At low pressure differences and velocities of JL = 0.025 m/s and JG = 1.88 m/s, a smooth stratified interface profile is observed, clearly separating the phases of water flowing continuously at the bottom and gas flowing at the top due to density differences, without any waves. As the velocities are increased to JL = 0.040 m/s and JG = 5.246 m/s, a ripple wave flow pattern occurs, characterized by small waves accompanied by long waves. Furthermore, increasing JL while decreasing JG to JL = 0.050 m/s and JG = 4.140 m/s leads to the formation of a stratified roll flow pattern, marked by long rolls, while pseudo slug flow occurs at JG = 5.246 m/s and JL = 0.076 m/s. This happens due to the increased velocity of the water phase causing the gas phase to become unstable, forming bubbles within the liquid
- Open Access
- 24 October 2024
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in ROTASI
- Vol. 26 (4)
PROSES MANUFAKTUR LENGAN PROSTESIS BERBASIS PENGGERAK KABEL HARNESS MENGGUNAKAN TEKNOLOGI 3D PRINTING
Enelitian ini menyoroti tantangan dan solusi dalam pengembangan prostesis tangan yang fungsional, terutama bagi individu dengan amputasi transradial, yang mengalami hambatan signifikan dalam aktivitas sehari-hari. WHO menyatakan bahwa 10% dari populasi global memiliki disabilitas, dengan 80% di antaranya berada di negara berpenghasilan rendah. Amputasi lengan dan tangan menyebabkan gangguan fungsional yang besar dan menurunkan kualitas hidup. Prostesis modern, meskipun menawarkan manfaat kosmetik dan mekanis, seringkali mahal dan sulit diakses di negara berkembang. Penelitian ini mengeksplorasi penggunaan teknologi pencetakan 3D dan desain berbantu komputer (CAD) untuk menciptakan prostesis yang lebih terjangkau dan fungsional. Dalam penelitian ini, proses desain menggunakan Autodesk Inventor 2020 dan Ultimaker Cura 5.7.1 untuk slicing (lapisan tipis) dan pencetakan 3D prostesis tangan. Hasil menunjukkan penyimpangan waktu dan dimensi dalam pencetakan yang memerlukan peningkatan proses untuk mencapai akurasi yang lebih baik. Uji coba dengan satu pasien menunjukkan fungsi dasar prostesis yang memadai, tetapi perlu penyesuaian lebih lanjut untuk meningkatkan kenyamanan dan efisiensi penggunaan. Penelitian ini menekankan pentingnya inovasi dan pengoptimalan dalam desain dan produksi prostesis untuk memenuhi kebutuhan pengguna dan meningkatkan kualitas hidup mereka
- 24 October 2024
- Published by Institute of Research and Community Services Diponegoro University (LPPM UNDIP) in ROTASI
- Vol. 26 (4)
Open AccessPROSES MANUFAKTUR LENGAN PROSTESIS BERBASIS PENGGERAK KABEL HARNESS MENGGUNAKAN TEKNOLOGI 3D PRINTING
Enelitian ini menyoroti tantangan dan solusi dalam pengembangan prostesis tangan yang fungsional, terutama bagi individu dengan amputasi transradial, yang mengalami hambatan signifikan dalam aktivitas sehari-hari. WHO menyatakan bahwa 10% dari populasi global memiliki disabilitas, dengan 80% di antaranya berada di negara berpenghasilan rendah. Amputasi lengan dan tangan menyebabkan gangguan fungsional yang besar dan menurunkan kualitas hidup. Prostesis modern, meskipun menawarkan manfaat kosmetik dan mekanis, seringkali mahal dan sulit diakses di negara berkembang. Penelitian ini mengeksplorasi penggunaan teknologi pencetakan 3D dan desain berbantu komputer (CAD) untuk menciptakan prostesis yang lebih terjangkau dan fungsional. Dalam penelitian ini, proses desain menggunakan Autodesk Inventor 2020 dan Ultimaker Cura 5.7.1 untuk slicing (lapisan tipis) dan pencetakan 3D prostesis tangan. Hasil menunjukkan penyimpangan waktu dan dimensi dalam pencetakan yang memerlukan peningkatan proses untuk mencapai akurasi yang lebih baik. Uji coba dengan satu pasien menunjukkan fungsi dasar prostesis yang memadai, tetapi perlu penyesuaian lebih lanjut untuk meningkatkan kenyamanan dan efisiensi penggunaan. Penelitian ini menekankan pentingnya inovasi dan pengoptimalan dalam desain dan produksi prostesis untuk memenuhi kebutuhan pengguna dan meningkatkan kualitas hidup mereka
- 16 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2001 (1) , 030003
Visualization study in the transition flow pattern of stratified to slug flow of air-water two phase flow in a horizontal pipe
Slug is one of the most avoided flows in the piping system network. The high pressure fluctuations can cause damage to the pipes. Therefore, prevention of the slug flow is very important. To understand the phenomenon, an experimental study to investigate the pattern of stratified to slug flow transition has been examined. The present work was conducted on a 26 mm diameter acrylic horizontal pipe with the length of 10 m. Air and water are used as working fluids. Visual image capture is done using Phantom Miro M310 High speed camera on L/D 180-210 from inlet. As a supporting visual observation result, CECM method is also used to measure liquid holdup of fluid flow. The onset of slugging mechanism due to change of both gas and liquid superficial velocity will be discussed. As a result, it is found that the slug formation from stratified flow is at least divided into two basic mechanisms. At low gas velocity, the slug stability condition is created by wave growth mechanism. The increase of JG resulted in the increase of aeration and the of the liquid slug length. When the gas velocity is above 3 m/s, wave coalescence and large disturbance waves initiated the onset of slugging. The Increase of JL on the high JG makes the roll waves higher to create a pseudo slug. In addition, it is found that the formation of high aeration slug is seen at JL = 0.3 m/s when JG is maintained at 3.77 m/s.
- 16 August 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 2001 (1) , 030003
Visualization study in the transition flow pattern of stratified to slug flow of air-water two phase flow in a horizontal pipe
Slug is one of the most avoided flows in the piping system network. The high pressure fluctuations can cause damage to the pipes. Therefore, prevention of the slug flow is very important. To understand the phenomenon, an experimental study to investigate the pattern of stratified to slug flow transition has been examined. The present work was conducted on a 26 mm diameter acrylic horizontal pipe with the length of 10 m. Air and water are used as working fluids. Visual image capture is done using Phantom Miro M310 High speed camera on L/D 180-210 from inlet. As a supporting visual observation result, CECM method is also used to measure liquid holdup of fluid flow. The onset of slugging mechanism due to change of both gas and liquid superficial velocity will be discussed. As a result, it is found that the slug formation from stratified flow is at least divided into two basic mechanisms. At low gas velocity, the slug stability condition is created by wave growth mechanism. The increase of JG resulted in the increase of aeration and the of the liquid slug length. When the gas velocity is above 3 m/s, wave coalescence and large disturbance waves initiated the onset of slugging. The Increase of JL on the high JG makes the roll waves higher to create a pseudo slug. In addition, it is found that the formation of high aeration slug is seen at JL = 0.3 m/s when JG is maintained at 3.77 m/s.
- 1 February 2017
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 81, 93-108
Experimental investigation on the initiation and flow development of gas-liquid slug two-phase flow in a horizontal pipe
- 1 February 2017
- Published by Elsevier in Experimental Thermal and Fluid Science
- Vol. 81, 93-108
Experimental investigation on the initiation and flow development of gas-liquid slug two-phase flow in a horizontal pipe
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1737 (1) , 040010
An improved algorithm of image processing technique for film thickness measurement in a horizontal stratified gas-liquid two-phase flow
Due to the importance of the two-phase flow researches for the industrial safety analysis, many researchers developed various methods and techniques to study the two-phase flow phenomena on the industrial cases, such as in the chemical, petroleum and nuclear industries cases. One of the developing methods and techniques is image processing technique. This technique is widely used in the two-phase flow researches due to the non-intrusive capability to process a lot of visualization data which are contain many complexities. Moreover, this technique allows to capture direct-visual information data of the flow which are difficult to be captured by other methods and techniques. The main objective of this paper is to present an improved algorithm of image processing technique from the preceding algorithm for the stratified flow cases. The present algorithm can measure the film thickness (hL) of stratified flow as well as the geometrical properties of the interfacial waves with lower processing time and random-access memory (RAM) usage than the preceding algorithm. Also, the measurement results are aimed to develop a high quality database of stratified flow which is scanty. In the present work, the measurement results had a satisfactory agreement with the previous works.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1737 (1) , 040010
An improved algorithm of image processing technique for film thickness measurement in a horizontal stratified gas-liquid two-phase flow
Due to the importance of the two-phase flow researches for the industrial safety analysis, many researchers developed various methods and techniques to study the two-phase flow phenomena on the industrial cases, such as in the chemical, petroleum and nuclear industries cases. One of the developing methods and techniques is image processing technique. This technique is widely used in the two-phase flow researches due to the non-intrusive capability to process a lot of visualization data which are contain many complexities. Moreover, this technique allows to capture direct-visual information data of the flow which are difficult to be captured by other methods and techniques. The main objective of this paper is to present an improved algorithm of image processing technique from the preceding algorithm for the stratified flow cases. The present algorithm can measure the film thickness (hL) of stratified flow as well as the geometrical properties of the interfacial waves with lower processing time and random-access memory (RAM) usage than the preceding algorithm. Also, the measurement results are aimed to develop a high quality database of stratified flow which is scanty. In the present work, the measurement results had a satisfactory agreement with the previous works.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1737 (1) , 040012
Experimental investigation on the interfacial characteristics of stratified air-water two-phase flow in a horizontal pipe
The interfacial wave characteristics of stratified air-water two-phase flow in a horizontal pipe were experimentally investigated by using the flush-mounted constant electric current method (CECM) sensors. The experiments were conducted in a horizontal two-phase flow loop 9.5 m long (L) consisting of transparent acrylic pipe of 26 mm i.d. (D). To obtain the stratified flow pattern, the superficial gas and liquid velocities were set to 1.02 – 3.77 m/s and 0.016 – 0.92 m/s, respectively. Several interfacial wave patterns as described by several investigators were identified. The common parameters such as liquid hold-up, probability distribution function, wave velocity and wave frequency were investigated as the function of the liquid and gas flow rates. The interfacial curvature was calculated on the basis of the liquid hold-up data from the CECM sensors and the liquid film thickness data from the image processing technique in the previous work. As a result, it was found that the mean liquid hold-up decreases with the increase of the superficial gas velocity. In the same sub flow pattern, the wave velocity increases as the superficial gas velocity increases. On the other hand, in the two-dimensional wave region, the dominant frequency decreases with the increase of the superficial liquid velocity.
- 1 January 2016
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1737 (1) , 040012
Experimental investigation on the interfacial characteristics of stratified air-water two-phase flow in a horizontal pipe
The interfacial wave characteristics of stratified air-water two-phase flow in a horizontal pipe were experimentally investigated by using the flush-mounted constant electric current method (CECM) sensors. The experiments were conducted in a horizontal two-phase flow loop 9.5 m long (L) consisting of transparent acrylic pipe of 26 mm i.d. (D). To obtain the stratified flow pattern, the superficial gas and liquid velocities were set to 1.02 – 3.77 m/s and 0.016 – 0.92 m/s, respectively. Several interfacial wave patterns as described by several investigators were identified. The common parameters such as liquid hold-up, probability distribution function, wave velocity and wave frequency were investigated as the function of the liquid and gas flow rates. The interfacial curvature was calculated on the basis of the liquid hold-up data from the CECM sensors and the liquid film thickness data from the image processing technique in the previous work. As a result, it was found that the mean liquid hold-up decreases with the increase of the superficial gas velocity. In the same sub flow pattern, the wave velocity increases as the superficial gas velocity increases. On the other hand, in the two-dimensional wave region, the dominant frequency decreases with the increase of the superficial liquid velocity.