MBMilan Bižić

Milan Bižić

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Milan Bižić has a total of 27 co-authors. Here are the top co-authors by number of shared publications:

  • Dragan Petrović

    University of Kragujevac, Faculty of Mechanical and Civil Engineering in Kraljevo, Dositejeva 19, 36000 Kraljevo, Serbia

    15 shared publications
  • Dragan Petrović

    Faculty of Mechanical and Civil Engineering in Kraljevo, University of Kragujevac, Kraljevo, Serbia

    4 shared publications
  • Aleksandar Antonijević

    Tehnoliv Komerc d.o.o Oraška 46 11320 Velika Plana Serbia

    1 shared publication
  • D. Petrovic

    Faculty of Mechanical Engineering Kraljevo, University of Kragujevac, Kraljevo, Serbia

    1 shared publication
  • Dragoslav Antonijević

    Tehnoliv Komerc d.o.o Oraška 46 11320 Velika Plana Serbia

    1 shared publication
  • Isidora Pančić

    Faculty of Civil Engineering University of Belgrade Belgrade Serbia

    1 shared publication

Latest Publications

  • Development of a systematic instrumentation methodology for continuous torque measurement in high-capacity shafts

    by Milan Bižić, Dragan Z Petrovic

    This paper presents the development of a systematic instrumentation methodology for continuous torque measurement in high-capacity shafts, based on the application of strain gauges. Within the proposed methodology, systematically derived solutions to the most important challenges in the development of instrumented shafts for torque measurement are presented, including the determination of optimal strain gauge locations, their arrangement and number, as well as the configuration of their connection into Wheatstone bridges. The main objective of the proposed methodology is to achieve high sensitivity and accuracy of torque measurement while simultaneously neutralizing parasitic effects in the output signal of the Wheatstone bridge. In addition, the model-based calibration procedure of the measurement system and an inverse torque determination algorithm based on the output signal of the Wheatstone bridge are presented. The developed methodology was tested on a finite element method (FEM) model of a high-capacity wind turbine shaft under various loading conditions, considering the combined effects of torque (to be measured), bending moments, as well as axial and transverse forces. The obtained results demonstrate that the developed methodology enables high numerical consistency in torque determination, with deviations between the prescribed torque in the FEM model and the torque obtained by inverse determination being less than 0.04%. Thus, it is confirmed that the proposed methodology can be successfully applied in the development of high-capacity instrumented shafts intended for continuous torque measurement.

  • Open Access

    CONCEPTUAL SOLUTION OF A TEST STAND FOR CALIBRATION OF MEASURING RAILWAY WHEELSETS FOR DIFFERENT TRACK GAUGES

    by Milan Bižić, Dragan Petrović

    The paper presents a conceptual solution of a test stand for calibration of measuring railway wheelsets. Unlike existing test stands that are designed for a single, fixed track gauge (1435 mm), the proposed conceptual solution enables testing and calibration of measuring wheelsets for different track gauges – 1435 mm and 1676 mm. The test stand is equipped with a linear platform for moving the contact point and a rotary platform for simulating the wheel angle of attack (angle up to 2.5°). The paper provides the basic concept, a description of the main functional units and technical specifications. The proposed solution is modular and adaptable, and can serve as a basis for further development and fabrication of the test stand.

  • Methodology for measuring pressure at the contact surface between a column footing model and a soil layer limited by a rigid base using Earth pressure cells

    by Stefan Mihajlović, Milan Bižić, Iva Despotović, Jovana Bojković, Marijana J anićijević Milačak

    The design of all building structures largely depends on the foundation support system, i.e., the relevant actions for structural design depend on soil–structure interaction. This paper describes a methodology for measuring pressures at the contact surface between a column footing model and a soil layer limited by a rigid base using earth pressure cells. The purpose of the research is to assess the reliability of the obtained results representing contact stress distributions between the interacting components under laboratory conditions. The concept of a reduced-scale footing model is presented, along with the procedure for preparing and installing earth pressure cells in the soil, with special emphasis on their position and data acquisition method. The main factors affecting measurement accuracy are also discussed, including soil characteristics, geometric and material properties of the tested footing model. The aim of this paper is to define an experimental procedure for a footing model and a soil layer limited by a rigid base that can serve as a basis for further experimental research and validation of numerical models. The reliability control of the measured contact stresses using earth pressure cells is based on comparison with analytical results. This experimental study examined contact pressures between a footing model and compacted sand using earth pressure cells. Measured pressures deviated significantly from calculated uniform values in the first test (48.3%) due to installation-induced soil disturbance, but improved to an acceptable 9.2% in the third test with proper surface preparation. The load–pressure relationship remained nearly linear across all measurements, consistent with sensor specifications.

  • Influence of signal-to-noise ratio on the accuracy of experimental determination of wheel-rail interaction forces

    by Milan Bižić, Dragan Petrović

    This paper analyzes the influence of the signal-to-noise ratio (SNR) on the accuracy of the experimental determination of wheel-rail interaction parameters – vertical force Q, lateral force Y, and contact point position ytk. The research was conducted on an instrumented wheelset developed from a standard wheelset, with strain gauges optimally positioned and connected into Wheatstone bridges. Experimental tests were carried out on a specialized test stand within the Laboratory for Railway Engineering and Structural Testing at the Faculty of Mechanical and Civil Engineering in Kraljevo, University of Kragujevac. The noise level in the electronic components of the measurement system and its influence on the final measurement error were analyzed based on the results of corresponding static and dynamic measurements. Using appropriate statistical analysis, it was determined that the noise level originating from the Wheatstone bridges and associated electronics causes significant dispersion of output signals, especially at lower force intensities. The results show that under lower loads (characteristic of empty vehicles) the SNR is less favorable, leading to an increase in the relative measurement errors of the aforementioned parameters. Conversely, under higher loads and critical values of the Y/Q ratio, which are of interest for assessing vehicle running stability according to relevant international standards, the SNR is significantly more favorable and measurement errors decrease. The obtained results confirm that the SNR is a key factor in the reliability of the measurement system for the experimental determination of wheel-rail interaction parameters. One of the directions for further improvement in measurement accuracy is the application of modern fiber-optic sensors, which have significantly higher resistance to electromagnetic interference and enable a more favorable SNR, thus opening a promising path toward a new generation of instrumented wheelsets with even higher measurement accuracy.

  • Open Access

    Design and calculation of test stand for testing personal fall protection equipment according to EN 364

    by Milan Bižić, Dragan Petrović

    This paper presents the design and calculation of a test stand intended for testing personal fall protection equipment in accordance with the requirements of the international standard EN 364. The objective of the study was to develop a reliable, safe, and structurally adequate test stand capable of performing both static and dynamic tests on components of fall arrest systems, including different types of personal fall protection systems, fall-arresters, anchor lines, safety harnesses, lanyards, energy absorbers, and connecting elements. The paper analyzes the requirements of EN 364 and defines the functional and structural characteristics of the test stand. Particular emphasis was placed on the static strength of the supporting structure, which was designed to withstand the maximum prescribed test forces without permanent deformation or structural failure, ensuring an adequate safety factor under the most unfavorable loading conditions. Furthermore, the dynamic performance of the test stand was analyzed through the evaluation of its natural frequencies, in accordance with standard requirements. The obtained calculation results confirm that the designed test stand fully complies with the requirements of EN 364 and enables accurate, reliable, and safe testing of personal fall protection equipment, thereby contributing to improved occupational safety and compliance with relevant standards.

  • Open Access

    Methodology of testing guided-type fall arresters with rail-based rigid anchor lines

    by Milan Bižić, Dragan Petrović

    Guided-type fall arresters with a rigid anchor line made of rail are among the most effective ways of fall protection from height. Their primary role is to ensure the user's safe movement during climbing and to protect them in the event of a sudden fall. Given that the functionality and reliability of this personal fall protection equipment directly impact the user's safety, the requirements for its quality are very rigorous. These requirements are precisely defined in European standards. Therefore, the aim of this paper is to provide a systematic overview of the methodology of testing of guided-type fall arresters with a rigid anchor line made of rail, in accordance with standard EN 353-1. This methodology is developed by the Laboratory for Railway Engineering and Structures Testing at the Faculty of Mechanical and Civil Engineering in Kraljevo, University of Kragujevac, Serbia. The paper analyzes the requirements for the physical, geometric, and mechanical characteristics of guided-type fall arresters and rigid anchor lines made of rail. Special attention is given to the procedures for performing both static and dynamic tests. The results of the conducted research provide a basis for assessing the potential for developing and manufacturing this type of personal fall protection equipment for the international market, while also contributing to ongoing efforts to improve its quality and safety by offering insights relevant to global production and certification processes.


  • Open Access

    Static testing of brake triangles of railway vehicles

    by Milan Bižić, Dragan Petrović, Dragoslav Antonijević, Aleksandar Antonijević, Ivan Miljković

    Brake triangles are very important parts of the braking system of railway vehicles that can significantly affect safety and security on the railway. In accordance with the international standard UIC 833, the requirements for manufacturers of brake triangles are very strict and require the supplier to provide proof of the quality of the brake triangles. Therefore, manufacturers must provide appropriate evidence of the quality of production of brake triangles in accordance with the above-mentioned international standard. The paper presents the basic requirements of the international standard UIC 833 and the development of the test stand for static testing of brake triangles of railway vehicles in the Serbian company Tehnoliv Komerc from Velika Plana. This allowed this company to start a very successful mass production of brake triangles for the international market.


  • Open Access

    Design of instrumented wheelset for measuring wheel-rail interaction forces

    by Milan Bižić, Dragan Petrović

    The paper presents the design of a specific type of instrumented wheelset intended for continuous measuring of lateral and vertical wheel-rail interaction forces 𝑌 and 𝑄, in accordance with regulations EN 14363 and UIC 518. The platform is a standard heavy wheelset BA314 with an axle-load of 25 tons. The key problems of smart instrumentalization are solved by the use of the wheel's numerical FEM model, which provides a significant cost reduction in the initial stage of development of the instrumented wheelset. The main goal is to ensure high measuring accuracy. The results of the FEM calculations in ANSYS are basis for identification of the distribution of strains on the internal and external side of the wheel disc. Consequently, the most convenient radial distances for installation of strain gauges of Wheatstone measuring bridges are determined. In the next stage, the disposition, number and ways of interconnection of strain gauges in the measuring bridges are defined. Ultimately, an algorithm for inverse determination of parameters 𝑌 and 𝑄 based on mixed signals from the measuring bridges is developed. The developed solution is validated through tests on specific examples, using a created numerical FEM model. A high accuracy of estimation of unknown parameters 𝑌 and 𝑄 is obtained with an error of less than 4.5%, while the error of estimation of their ratio 𝑌 /𝑄 is less than 2%. Therefore, the proposed solution can be efficiently used in the instrumentalization of the considered wheelset, while the problems of its practical implementation will be the subject of further research.


  • Optimization of suspension of rail vehicles with coil springs using marine predators algorithm

    by Milan Bižić, Radovan Bulatović, Dragan Petrović

    The topic of this paper is the usage of the algorithm of marine predator (MPA) in the optimization of the suspension of rail vehicles with coil springs. The aim is to reduce the mass of set of coil springs as the main parts of rail vehicles suspension. The optimized set of coil springs must satisfy the appropriate conditions related to the suspension characteristics, with the aim of achieving the required operation quality and running security of the observed rail vehicle. Starting from the bi-linear characteristic of rail vehicles suspension and the analytical description of its parameters, an optimization problem is formulated. It is composed of six optimization parameters, an objective function and 16 constraints (eight for each coil spring in the set). The developed approach is applied in two specific examples of suspension optimization of four-axled freight wagons, the first with axle load of 200 kN and the second with axle load of 225 kN. The optimization problem is resolved using MPA. The acquired results showed that the given optimization approach with MPA provide a significant mass decrease compared to conventional design method of rail vehicles suspension with coil springs. The mass decrease of one set of coil springs in both examples is about 15.5%. Given that each considered four-axled freight wagon has 16 sets of coil springs, the decrease of the total coil springs mass per wagon in both examples is more than 60 kg. Since certified rail vehicles are commonly produced in large series, the proposed approach can be very significant for increasing profitability in the rail vehicles industry.