Tatiana Pais
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tatiana Pais has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Gianmarco Vergassola
University of Genova, Italy
8 shared publications A. Tonelli
3 shared publications- Dario Boote
University of Genova, Italy
3 shared publications Dario Boote
University of Genoa
2 shared publicationsL. Gragnani
2 shared publications- Paolo Silvestri
Department of Mechanical, Energy, Management and Transportation Engineering (DIME), University of Genova, Genova, Italy
2 shared publications
Latest Publications
- Open Access
- 11 November 2026
- Published by Elsevier in Ocean Engineering
- Vol. 371
A procedure for the numerical simulation of underwater radiated noise from machineries with real data validation
- 11 November 2026
- Published by Elsevier in Ocean Engineering
- Vol. 371
Open AccessA procedure for the numerical simulation of underwater radiated noise from machineries with real data validation
- Open Access
- 17 February 2025
- Published by Elsevier in Ocean Engineering
- Vol. 323
Sustainable yacht refits: Structural solutions in methanol-powered conversion
- 17 February 2025
- Published by Elsevier in Ocean Engineering
- Vol. 323
Open AccessSustainable yacht refits: Structural solutions in methanol-powered conversion
- Open Access
- 19 August 2024
- Published by Elsevier in Ocean Engineering
- Vol. 311
Full scale cruise ship dynamic identification using operational modal analysis on sea trial data measurements
- 19 August 2024
- Published by Elsevier in Ocean Engineering
- Vol. 311
Open AccessFull scale cruise ship dynamic identification using operational modal analysis on sea trial data measurements
- 28 July 2023
- Published by Elsevier in Ocean Engineering
- Vol. 285, 115428
Airborne sound transmission loss of ship bulkheads: A new methodological approach for in-laboratory assessment by including low frequencies
- 28 July 2023
- Published by Elsevier in Ocean Engineering
- Vol. 285, 115428
Airborne sound transmission loss of ship bulkheads: A new methodological approach for in-laboratory assessment by including low frequencies
- 1 June 2022
- Published by Springer Nature in Journal of Marine Science and Application
- Vol. 21 (2) , 59-68
Evaluation of the Residual Capacity of a Submarine for Different Limit States with Various Initial Imperfection Models
- 1 June 2022
- Published by Springer Nature in Journal of Marine Science and Application
- Vol. 21 (2) , 59-68
Evaluation of the Residual Capacity of a Submarine for Different Limit States with Various Initial Imperfection Models
- 1 October 2021
- Published by Elsevier in Ocean Engineering
- Vol. 238
An experimental-driven methodology for the evaluation of pre-tension of stays and shrouds for large sailing vessels
- 1 October 2021
- Published by Elsevier in Ocean Engineering
- Vol. 238
An experimental-driven methodology for the evaluation of pre-tension of stays and shrouds for large sailing vessels
- 18 July 2018
- Published by Taylor & Francis in Ships and Offshore Structures
- Vol. 14 (3) , 281-294
Hull–furniture interaction in the primary response to global loads of a carbon fibre sailing yacht
High performance sailing yachts are generally designed assuming high local and global loads transmitted by rigs to hull structures. The above-mentioned loading conditions can become critical for large hulls also in terms of displacements when composite materials are used. In this scenario, it is very important to use lightweight and high-performance materials, such as carbon fibres. In fact, also some ‘non structural’ components, such as outfit and furniture, are built in carbon fibres and, therefore, can be considered contributing to the hull local and global strength. The aim of this work is to investigate the contribution level of those ‘non-structural’ components to the hull strength. Two different finite element models of a 94 ft sailing yacht, with and without ‘non structural components’, have been carried out in order to evaluate their contribution to the primary hull response to longitudinal bending moment and dock tuning load.
- 18 July 2018
- Published by Taylor & Francis in Ships and Offshore Structures
- Vol. 14 (3) , 281-294
Hull–furniture interaction in the primary response to global loads of a carbon fibre sailing yacht
High performance sailing yachts are generally designed assuming high local and global loads transmitted by rigs to hull structures. The above-mentioned loading conditions can become critical for large hulls also in terms of displacements when composite materials are used. In this scenario, it is very important to use lightweight and high-performance materials, such as carbon fibres. In fact, also some ‘non structural’ components, such as outfit and furniture, are built in carbon fibres and, therefore, can be considered contributing to the hull local and global strength. The aim of this work is to investigate the contribution level of those ‘non-structural’ components to the hull strength. Two different finite element models of a 94 ft sailing yacht, with and without ‘non structural components’, have been carried out in order to evaluate their contribution to the primary hull response to longitudinal bending moment and dock tuning load.
- 1 May 2018
- Published by Elsevier in Ocean Engineering
- Vol. 155, 310-323
Vibration analysis for the comfort assessment of a superyacht under hydrodynamic loads due to mechanical propulsion
- 1 May 2018
- Published by Elsevier in Ocean Engineering
- Vol. 155, 310-323
Vibration analysis for the comfort assessment of a superyacht under hydrodynamic loads due to mechanical propulsion
- 7 December 2017
- Published by SAGE Publications in International Shipbuilding Progress
- Vol. 64 (1-2) , 25-40
On the damping coefficient of laminated glass for yacht industry
After a long period in which the most attractive characteristic of a motor yacht was represented by her maximum speed, nowadays the target has moved towards comfort on board which became the fundamental parameter to deal with in the yacht design proc
- 7 December 2017
- Published by SAGE Publications in International Shipbuilding Progress
- Vol. 64 (1-2) , 25-40
On the damping coefficient of laminated glass for yacht industry
After a long period in which the most attractive characteristic of a motor yacht was represented by her maximum speed, nowadays the target has moved towards comfort on board which became the fundamental parameter to deal with in the yacht design proc
- 1 December 2017
- Published by Royal Institution of Naval Architects
- Vol. 159 (B2)
THERMAL LOAD EFFECTS ON ALUMINUM LIGHT ALLOY PLATES WITH EPOXY COATINGS
When the assembling of hull structure is completed, the sides of metal motor yachts are usually affected by bumps and hollows coming from welding plates to each other and plates to frames. These defects, normally tolerated on merchant ships, cannot be accepted on superyachts for which the external surface must be smooth and glossy. For this reason the surface finishing is achieved by a long and delicate process of filling, fairing and painting. The final result of this process is very important for the yacht aesthetics as the general appearance of the vessel depends on the external painting. As a matter of fact the quality of painting depends mainly on the undercoat preparation to assure an adequate grip and, most of all, a perfect smooth and faired surface. Despite accurate preparation and painting, surface conditions can undergo undesired alteration because of excessive heating due, as an example, to a long exposure to solar radiation. While stresses do not reach significant values because of the relatively low intensity of thermal loads, strains could still cause very slight surface distortions and undulations which are perceived by human eye as a surface defect. The phenomenon becomes particularly evident if the surface is painted with a dark colour. In this paper an investigation on the influence of temperature on the stress and strain distribution of aluminium light alloy plates coated by filler layers of different kind and thickness is reported. The study has been performed by FEM structural analyses calibrated by experimental measurements performed on laboratory specimens. This work represents the continuation of a research begun some time ago with the measurement of temperatures on yacht hulls exposed to solar radiation in different conditions.
- 1 December 2017
- Published by Royal Institution of Naval Architects
- Vol. 159 (B2)
THERMAL LOAD EFFECTS ON ALUMINUM LIGHT ALLOY PLATES WITH EPOXY COATINGS
When the assembling of hull structure is completed, the sides of metal motor yachts are usually affected by bumps and hollows coming from welding plates to each other and plates to frames. These defects, normally tolerated on merchant ships, cannot be accepted on superyachts for which the external surface must be smooth and glossy. For this reason the surface finishing is achieved by a long and delicate process of filling, fairing and painting. The final result of this process is very important for the yacht aesthetics as the general appearance of the vessel depends on the external painting. As a matter of fact the quality of painting depends mainly on the undercoat preparation to assure an adequate grip and, most of all, a perfect smooth and faired surface. Despite accurate preparation and painting, surface conditions can undergo undesired alteration because of excessive heating due, as an example, to a long exposure to solar radiation. While stresses do not reach significant values because of the relatively low intensity of thermal loads, strains could still cause very slight surface distortions and undulations which are perceived by human eye as a surface defect. The phenomenon becomes particularly evident if the surface is painted with a dark colour. In this paper an investigation on the influence of temperature on the stress and strain distribution of aluminium light alloy plates coated by filler layers of different kind and thickness is reported. The study has been performed by FEM structural analyses calibrated by experimental measurements performed on laboratory specimens. This work represents the continuation of a research begun some time ago with the measurement of temperatures on yacht hulls exposed to solar radiation in different conditions.