Hans Butler
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hans Butler has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
Tuan T. Nguyen
Department of Electrical Engineering, Eindhoven, University of Technology, P.O. Box 513, Eindhoven, 5600 MB, The Netherlands
6 shared publications- Mircea Lazar
Eindhoven University of Technology
5 shared publications Marcel F. Heertjes
4 shared publicationsG. Honderd
Department of Electrical Engineering, Control Laboratory, Delft University of Technology, PO Box 5031, NL-2600 GA Delft, The Netherlands
3 shared publicationsMichiel A. Beijen
3 shared publicationsMircea Lazar
Department of Electrical Engineering, Eindhoven, University of Technology, P.O. Box 513, Eindhoven, 5600 MB, The Netherlands
3 shared publications
Latest Publications
- Open Access
- 6 January 2025
- Published by Elsevier in Mechatronics
- Vol. 106
Structured physics-guided neural networks for electromagnetic commutation applied to industrial linear motors
- 6 January 2025
- Published by Elsevier in Mechatronics
- Vol. 106
Open AccessStructured physics-guided neural networks for electromagnetic commutation applied to industrial linear motors
- 21 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Control Systems Letters
- Vol. 7, 2593-2598
On Improved Commutation for Moving-Magnet Planar Actuators
The demand for high-precision and high-throughput motion control systems has increased significantly in recent years. The use of moving-magnet planar actuators (MMPAs) is gaining popularity due to their advantageous characteristics, such as complete environmental decoupling and reduction of stage mass. Nonetheless, model-based commutation techniques for MMPAs are compromised by misalignment between the mover and coil array and mismatch between the ideal electromagnetic model and the physical system, often leading to decreased system performance. To address this issue, a novel improved commutation approach is proposed in this paper, which is applicable for general planar motor applications, by means of dynamic regulation of the position dependence of the ideal model-based commutation algorithm, which allows for attenuation of magnetic misalignment, manufacturing inaccuracies and other unmodelled phenomena. The effectiveness of the proposed approach is validated through experiments using a state-of-the-art moving-magnet planar actuator prototype.
- 21 June 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Control Systems Letters
- Vol. 7, 2593-2598
On Improved Commutation for Moving-Magnet Planar Actuators
The demand for high-precision and high-throughput motion control systems has increased significantly in recent years. The use of moving-magnet planar actuators (MMPAs) is gaining popularity due to their advantageous characteristics, such as complete environmental decoupling and reduction of stage mass. Nonetheless, model-based commutation techniques for MMPAs are compromised by misalignment between the mover and coil array and mismatch between the ideal electromagnetic model and the physical system, often leading to decreased system performance. To address this issue, a novel improved commutation approach is proposed in this paper, which is applicable for general planar motor applications, by means of dynamic regulation of the position dependence of the ideal model-based commutation algorithm, which allows for attenuation of magnetic misalignment, manufacturing inaccuracies and other unmodelled phenomena. The effectiveness of the proposed approach is validated through experiments using a state-of-the-art moving-magnet planar actuator prototype.
- 11 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (1) , 242-249
Active Deformation Control for a Magnetically Levitated Planar Motor Mover
This article describes a method for the active control of the deformations on a magnetically levitated moving-magnet planar motor. The planar motor under consideration is comprised of a stator on a double coil array configuration and a mover with permanent magnets, and it is designed to perform positioning tasks with nanometer level of accuracy. Due to the spatially asymmetric, nonuniform force distribution on the magnet plate, mechanical deformations are induced to the mover, which can severely hinder the desired positioning accuracy. The proposed method overcomes this challenge by properly shaping the force distribution on the moving magnet plate, which is enabled by the presence of multiple coils interacting with the mover, corresponding to an “overactuation” scheme. As a consequence, the independent control of elementary deformation shapes (modes) is achieved. The proposed overactuation scheme is experimentally validated on a planar motor prototype, proving the efficiency of the proposed method during both standstill and motion.
- 11 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (1) , 242-249
Active Deformation Control for a Magnetically Levitated Planar Motor Mover
This article describes a method for the active control of the deformations on a magnetically levitated moving-magnet planar motor. The planar motor under consideration is comprised of a stator on a double coil array configuration and a mover with permanent magnets, and it is designed to perform positioning tasks with nanometer level of accuracy. Due to the spatially asymmetric, nonuniform force distribution on the magnet plate, mechanical deformations are induced to the mover, which can severely hinder the desired positioning accuracy. The proposed method overcomes this challenge by properly shaping the force distribution on the moving magnet plate, which is enabled by the presence of multiple coils interacting with the mover, corresponding to an “overactuation” scheme. As a consequence, the independent control of elementary deformation shapes (modes) is achieved. The proposed overactuation scheme is experimentally validated on a planar motor prototype, proving the efficiency of the proposed method during both standstill and motion.
- 1 December 2018
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 436, 220-235
Disturbance feedforward control for active vibration isolation systems with internal isolator dynamics
- 1 December 2018
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 436, 220-235
Disturbance feedforward control for active vibration isolation systems with internal isolator dynamics
- 1 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 927-932
Nonlinear Model Predictive Control of Ironless Linear Motors
As the demands for accuracy and throughput in industrial positioning systems are increasing, classical control of ironless linear motors (ILMs) is facing its limit. Classical control scheme of an ILM typically consists of a simple sinusoidal commutation algorithm and a PID feedback controller. Classical commutation cannot compensate for parasitic effects, while classical PID feedback controller cannot guarantee constraints satisfaction. This problem can be addressed by replacing classical commutation with optimal commutation and PID controller with linear model predictive controller (LMPC). However, this LMPC and optimal commutation scheme requires solving two separate optimization problems, which is not optimal and can lead to infeasibility. In this paper we present a nonlinear model predictive control (NMPC) scheme for ILMs. The scheme requires solving only a single optimization problem. It can guarantee constraints satisfaction and is capable of compensating for parasitic forces. Simulation results are presented for demonstration.
- 1 August 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 927-932
Nonlinear Model Predictive Control of Ironless Linear Motors
As the demands for accuracy and throughput in industrial positioning systems are increasing, classical control of ironless linear motors (ILMs) is facing its limit. Classical control scheme of an ILM typically consists of a simple sinusoidal commutation algorithm and a PID feedback controller. Classical commutation cannot compensate for parasitic effects, while classical PID feedback controller cannot guarantee constraints satisfaction. This problem can be addressed by replacing classical commutation with optimal commutation and PID controller with linear model predictive controller (LMPC). However, this LMPC and optimal commutation scheme requires solving two separate optimization problems, which is not optimal and can lead to infeasibility. In this paper we present a nonlinear model predictive control (NMPC) scheme for ILMs. The scheme requires solving only a single optimization problem. It can guarantee constraints satisfaction and is capable of compensating for parasitic forces. Simulation results are presented for demonstration.
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 6690-6696
Experimental Validation of Inversion Techniques for an LPV motion system
- 1 June 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 6690-6696
Experimental Validation of Inversion Techniques for an LPV motion system
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 3781-3786
A method to guarantee local convergence for sequential quadratic programming with poor Hessian approximation
Sequential Quadratic Programming (SQP) is a powerful class of algorithms for solving nonlinear optimization problems. Local convergence of SQP algorithms is guaranteed when the Hessian approximation used in each Quadratic Programming subproblem is close to the true Hessian. However, a good Hessian approximation can be expensive to compute. Low cost Hessian approximations only guarantee local convergence under some assumptions, which are not always satisfied in practice. To address this problem, this paper proposes a simple method to guarantee local convergence for SQP with poor Hessian approximation. The effectiveness of the proposed algorithm is demonstrated in a numerical example.
- 1 December 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 3781-3786
A method to guarantee local convergence for sequential quadratic programming with poor Hessian approximation
Sequential Quadratic Programming (SQP) is a powerful class of algorithms for solving nonlinear optimization problems. Local convergence of SQP algorithms is guaranteed when the Hessian approximation used in each Quadratic Programming subproblem is close to the true Hessian. However, a good Hessian approximation can be expensive to compute. Low cost Hessian approximations only guarantee local convergence under some assumptions, which are not always satisfied in practice. To address this problem, this paper proposes a simple method to guarantee local convergence for SQP with poor Hessian approximation. The effectiveness of the proposed algorithm is demonstrated in a numerical example.
- 1 July 2017
- Published by Elsevier in IFAC-PapersOnLine
- Vol. 50 (1) , 13384-13389
H∞ feedback and feedforward controller design for active vibration isolators
- 1 July 2017
- Published by Elsevier in IFAC-PapersOnLine
- Vol. 50 (1) , 13384-13389
H∞ feedback and feedforward controller design for active vibration isolators