Igor Krasnikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Igor Krasnikov has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Anatolii Babichenko
National technical university «Kharkiv polytechnic institute
6 shared publications - Juliya Babichenko
Ukrainian State University of Railway Transport
6 shared publications - Ihor Lysachenko
National technical university «Kharkiv polytechnic institute
5 shared publications - Oleksandr Dzevochko
National Technical University “Kharkiv Polytechnic Institute
3 shared publications - Yana Kravchenko
National Technical University «Kharkiv Polytechnic Institute», Ukraine
3 shared publications Anatoliy Babichenko
2 shared publications
Latest Publications
- Open Access
- 30 June 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (2 (141)) , 101-110
Evaluation of edge-based data stream processing scenarios in industrial automation systems: data reduction, latency, and resource utilization
This study explores the stream of process measurements after processing at the edge node in the chain “field-level equipment → edge node → SCADA → database”. The task addressed relates to the insufficient quantitative assessment of the impact of processing scenarios at the edge level on the stream intensity, time characteristics, and load of system nodes. This paper considers an edge-based approach to the stream processing of process data from industrial automation systems. 5 scenarios for processing the stream of process data at the edge node have been considered. A comparative analysis was performed by the number of records after processing, end-to-end latency, reduction ratio, jitter, and resource load. To that end, a bench was implemented that reproduces data transmission from field-level equipment through an edge node to the SCADA system and database. The basic mode without optimization, filtering by the change threshold, periodic selection, aggregation in a time window, event filtering, and a hybrid scheme were investigated. All edge processing scenarios reduced the stream intensity compared to the baseline. The largest reduction was provided by EV and DB: 0.976 and 0.962. For most scenarios, the end-to-end latency was 71.064–81.197 ms, for HYB – 112.457 ms. The lowest jitter was obtained for EV – 25.98 ms and DB – 38.521 ms. This is explained by the fact that event and threshold selection cut off background signal changes. Preprocessing reduces the network load without a noticeable increase in the load of the edge node. This makes it possible to consider processing at the edge node as a means of data reduction and formation of a controlled stream for the SCADA system and database. The practical significance implies using the results for comparative selection of processing scenarios for process data taking into account network traffic, latency stability, as well as edge node resources
- 30 June 2026
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (2 (141)) , 101-110
Open AccessEvaluation of edge-based data stream processing scenarios in industrial automation systems: data reduction, latency, and resource utilization
This study explores the stream of process measurements after processing at the edge node in the chain “field-level equipment → edge node → SCADA → database”. The task addressed relates to the insufficient quantitative assessment of the impact of processing scenarios at the edge level on the stream intensity, time characteristics, and load of system nodes. This paper considers an edge-based approach to the stream processing of process data from industrial automation systems. 5 scenarios for processing the stream of process data at the edge node have been considered. A comparative analysis was performed by the number of records after processing, end-to-end latency, reduction ratio, jitter, and resource load. To that end, a bench was implemented that reproduces data transmission from field-level equipment through an edge node to the SCADA system and database. The basic mode without optimization, filtering by the change threshold, periodic selection, aggregation in a time window, event filtering, and a hybrid scheme were investigated. All edge processing scenarios reduced the stream intensity compared to the baseline. The largest reduction was provided by EV and DB: 0.976 and 0.962. For most scenarios, the end-to-end latency was 71.064–81.197 ms, for HYB – 112.457 ms. The lowest jitter was obtained for EV – 25.98 ms and DB – 38.521 ms. This is explained by the fact that event and threshold selection cut off background signal changes. Preprocessing reduces the network load without a noticeable increase in the load of the edge node. This makes it possible to consider processing at the edge node as a means of data reduction and formation of a controlled stream for the SCADA system and database. The practical significance implies using the results for comparative selection of processing scenarios for process data taking into account network traffic, latency stability, as well as edge node resources
- Open Access
- 2 April 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: New solutions in modern technologies
- No. 1(27),p. 54-60
DECISION-MAKING SUBSYSTEM OF THE CONTROL SYSTEM FOR ABSORPTION REFRIGERATION UNITS IN AMMONIA PRODUCTION
It is shown that in the technological complex of secondary condensation in ammonia production, seasonal and daily fluctuations of ambient air temperature change the heat removal conditions in air-cooled condensers, which leads to deviations of ammonia vapor condensation pressure and disturbs the stability of generation, rectification, and condensation modes. The consequences of such disturbances for the operation of jet compressors are analyzed, in particular the variation of the injection coefficient and the need for prompt coordination of the motive steam flow rate with the current condensation parameters. An approach to supervisory control is considered, within which the decision-making subsystem generates recommendations for the operator on switching individual jet compressors on or off and setting the motive steam flow rate based on the calculated assessment of the injection coefficient. Emphasis is placed on the algorithmic support based on a mathematical description of a single-phase jet compressor with a cylindrical mixing chamber and the use of gas-dynamic functions to determine limiting regimes and convergent computational procedures. It is confirmed that the proposed sequence of calculations makes it possible to coordinate the motive steam flow rate with changes in temperature and condensation pressure in air-cooled units and provides a formalized selection of the number of operating jet compressors under off-design conditions. The algorithm is implemented in the MATLAB software environment, and its validation is carried out using experimental data from industrial operation. The obtained results demonstrate the possibility of rapid switching of jet compressor configurations depending on condensation conditions and the calculated injection coefficient, which contributes to a reduction in electricity and natural gas consumption and improves the reproducibility of control decisions in the supervisory loop.
- 2 April 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University «KhPI» Series: New solutions in modern technologies
- No. 1(27),p. 54-60
Open AccessDECISION-MAKING SUBSYSTEM OF THE CONTROL SYSTEM FOR ABSORPTION REFRIGERATION UNITS IN AMMONIA PRODUCTION
It is shown that in the technological complex of secondary condensation in ammonia production, seasonal and daily fluctuations of ambient air temperature change the heat removal conditions in air-cooled condensers, which leads to deviations of ammonia vapor condensation pressure and disturbs the stability of generation, rectification, and condensation modes. The consequences of such disturbances for the operation of jet compressors are analyzed, in particular the variation of the injection coefficient and the need for prompt coordination of the motive steam flow rate with the current condensation parameters. An approach to supervisory control is considered, within which the decision-making subsystem generates recommendations for the operator on switching individual jet compressors on or off and setting the motive steam flow rate based on the calculated assessment of the injection coefficient. Emphasis is placed on the algorithmic support based on a mathematical description of a single-phase jet compressor with a cylindrical mixing chamber and the use of gas-dynamic functions to determine limiting regimes and convergent computational procedures. It is confirmed that the proposed sequence of calculations makes it possible to coordinate the motive steam flow rate with changes in temperature and condensation pressure in air-cooled units and provides a formalized selection of the number of operating jet compressors under off-design conditions. The algorithm is implemented in the MATLAB software environment, and its validation is carried out using experimental data from industrial operation. The obtained results demonstrate the possibility of rapid switching of jet compressor configurations depending on condensation conditions and the calculated injection coefficient, which contributes to a reduction in electricity and natural gas consumption and improves the reproducibility of control decisions in the supervisory loop.
- 27 March 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Integrated Technologies and Energy Saving
- No. 1,p. 72-83
HYBRID CONTROL SYSTEM FOR SPRAY DRYING OF EXTRACT WITH NEURO-FUZZY CORRECTION OF SETPOINTS
This paper proposes a hybrid control system for spray drying of extract, aimed at improving the accuracy of moisture stabilization of the dried product in the presence of crosscouplings between control loops and external disturbances caused by variations in raw material properties and air environment parameters. The basic control structure preserves the con-ventional industrial implementation of local PID control loops, while the coordination of in-teracting loops is performed at a supervisory level in the form of an ANFIS-based setpoint corrector. The corrector generates incremental adjustments to the setpoints of the inlet drying-agent temperature and its flow rate based on the current values of outlet gas temperature, product moisture content, and absolute humidity of the inlet air. This architecture enables par-tial compensation of mutual interactions between process channels without altering the struc-ture of local PID control or requiring modifications to the hardware configuration of the sys-tem.The mathematical model of the process was developed in the MATLAB/Simulink en-vironment by identifying individual channels using static characteristics and dynamic re-sponses within a selected operating range, followed by approximation with transfer functions including dead time. Model adequacy was confirmed by comparing simulated output varia-bles with published experimental data from open sources and by iterative refinement of trans-fer-function parameters until a mean relative error of 3% was achieved. Since experimental data from an actual industrial installation were unavailable for training the neuro-fuzzy model, ANFIS training was performed using training datasets generated in the simulation environ-ment based on the developed mathematical model, static dependencies, and a series of simula-tion runs.The effectiveness of the proposed approach was evaluated through comparative simu-lation of a conventional PID-based control system and a hybrid system with ANFIS-based setpoint correction. Performance indicators included overshoot, settling time, and the integral squared error (ISE) criterion under a baseline operating scenario. It was established that the application of the ANFIS corrector reduces the settling time by 33 % (from 180 to 120 s), de-creases overshoot by a factor of 2.4 (from 12 % to 5 %), and lowers the ISE value by 48 % (from 1.00 to 0.52) compared with the PID-only control system. Further research should focus on experimental validation of the proposed algorithm on real equipment, additional training of the ANFIS model using experimental data, and assessment of the supervisory control layer performance in the presence of measurement noise and actuator constraints.
- 27 March 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Integrated Technologies and Energy Saving
- No. 1,p. 72-83
HYBRID CONTROL SYSTEM FOR SPRAY DRYING OF EXTRACT WITH NEURO-FUZZY CORRECTION OF SETPOINTS
This paper proposes a hybrid control system for spray drying of extract, aimed at improving the accuracy of moisture stabilization of the dried product in the presence of crosscouplings between control loops and external disturbances caused by variations in raw material properties and air environment parameters. The basic control structure preserves the con-ventional industrial implementation of local PID control loops, while the coordination of in-teracting loops is performed at a supervisory level in the form of an ANFIS-based setpoint corrector. The corrector generates incremental adjustments to the setpoints of the inlet drying-agent temperature and its flow rate based on the current values of outlet gas temperature, product moisture content, and absolute humidity of the inlet air. This architecture enables par-tial compensation of mutual interactions between process channels without altering the struc-ture of local PID control or requiring modifications to the hardware configuration of the sys-tem.The mathematical model of the process was developed in the MATLAB/Simulink en-vironment by identifying individual channels using static characteristics and dynamic re-sponses within a selected operating range, followed by approximation with transfer functions including dead time. Model adequacy was confirmed by comparing simulated output varia-bles with published experimental data from open sources and by iterative refinement of trans-fer-function parameters until a mean relative error of 3% was achieved. Since experimental data from an actual industrial installation were unavailable for training the neuro-fuzzy model, ANFIS training was performed using training datasets generated in the simulation environ-ment based on the developed mathematical model, static dependencies, and a series of simula-tion runs.The effectiveness of the proposed approach was evaluated through comparative simu-lation of a conventional PID-based control system and a hybrid system with ANFIS-based setpoint correction. Performance indicators included overshoot, settling time, and the integral squared error (ISE) criterion under a baseline operating scenario. It was established that the application of the ANFIS corrector reduces the settling time by 33 % (from 180 to 120 s), de-creases overshoot by a factor of 2.4 (from 12 % to 5 %), and lowers the ISE value by 48 % (from 1.00 to 0.52) compared with the PID-only control system. Further research should focus on experimental validation of the proposed algorithm on real equipment, additional training of the ANFIS model using experimental data, and assessment of the supervisory control layer performance in the presence of measurement noise and actuator constraints.
- 27 February 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI" A series of "Information and Modeling"
- Vol. 1 (1(15)) , 69-82
Theoretical Foundations of Streaming Processing of Technological Data in Industrial Automation Systems
The processing of growing volumes of technological data in industrial automation systems, as well as the limitations of traditional archiving in databases with deferred analysis, are considered, taking into account time requirements and infrastructure load. The concepts of stream processing are generalized and adapted to technological measurements and events in automated control systems. A multi-level model is presented that combines data source levels, SCADA, and storage subsystems. A test bench demonstrates a reduction in the intensity of writing to a relational database while preserving characteristic signal changes and similar statistical delay indicators. Tabl.: 2. Refs.: 23 items.
- 27 February 2026
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI" A series of "Information and Modeling"
- Vol. 1 (1(15)) , 69-82
Theoretical Foundations of Streaming Processing of Technological Data in Industrial Automation Systems
The processing of growing volumes of technological data in industrial automation systems, as well as the limitations of traditional archiving in databases with deferred analysis, are considered, taking into account time requirements and infrastructure load. The concepts of stream processing are generalized and adapted to technological measurements and events in automated control systems. A multi-level model is presented that combines data source levels, SCADA, and storage subsystems. A test bench demonstrates a reduction in the intensity of writing to a relational database while preserving characteristic signal changes and similar statistical delay indicators. Tabl.: 2. Refs.: 23 items.
- Open Access
- 11 November 2025
- Published by Private Company Technology Center
Chapter 1. Technological aspects of computer control of the secondary condensation complex of ammonia production under uncertainty
The object of study is a technological complex of secondary condensation (TCS) of large-capacity ammonia synthesis units of AM-1360 series, which provides final cooling and separation of condensed product ammonia from circulating gas (CG). The possibility of increasing the energy efficiency of production by modernising the equipment and technological design of the TACC was established. This is achieved by removing an energy-intensive electrically driven turbo-compressor refrigeration unit (TCRU) from the scheme and creating an adaptive system of optimal software control. The expediency of applying a systematic approach to solving such a complex problem, the scientific basis of which is mathematical modelling and process identification, is shown. The peculiarities of the operating conditions of the TKVK and the primary condensation unit are analysed. The research results revealed uncertainties in the functioning of such components as the condensing column (CC) and low-temperature evaporators (LTE), which are connected to the operation scheme of two absorption-cooling units (ACU) and the ATC. The algorithms for generating an information array of experimental data and numerical estimation of uncertainties, in particular, heat transfer coefficients in the BF and LST, as well as ammonia concentration at the outlet of the primary condensation unit and the BF, were developed. The algorithms provide for the separation of transient modes in the operation of the TKVK, verification of stationarity, reproducibility of the process and the hypothesis of the normality of the empirical distribution, which makes it possible to use a stochastic approximation method for numerical estimation of uncertainties. Based on the results of processing the experimental data, a discrepancy between the real and design heat transfer coefficients was found, which is due to an underestimation of the condensation thermal resistance. The heat transfer processes in the BF and CNT as part of the CCS were identified and equations were obtained to determine the heat transfer coefficients, heat transfer, condensation thermal resistance, and ammonia concentration in the GHG at the inlet and outlet of the BF. The conditions of the required temperature distribution in the TCWC to exclude it from the ATC scheme and reduce the DH cooling temperature in the HST by 5 °C compared to the original variant at the maximum DH heat load at the inlet of the complex were determined by mathematical modelling. The developed scheme of the TACC is characterised by greater energy efficiency due to the use of only heat-using refrigeration systems of AHU and steam generating units (SGU), which utilise the heat of material flows of both low temperature potential (up to 150 °C) and ultra-low (up to 90 °C). Using the method of mathematical modelling of the VNT, the regularity of the extreme nature of the dependence of the cooling capacity and cooling temperature of the DH on the phlegm flow rate was established. The achievement of the maximum cooling capacity, and hence the minimum cooling temperature of the DH at a certain temperature head, is due to the critical mode of bubble boiling of the refrigerant. The dependencies of the DH cooling temperature on the controlling effect of the phlegm flow rate are determined, which characterise the shift of the extremum under conditions of changing the coordinates of the perturbation vector, and hence the change in the energy efficiency of ammonia production (annual natural gas consumption). Algorithmic software was developed to solve the problems of identification, obtaining a mathematical model of the CNT evaporator and numerical estimation of the optimal state vector (cooling temperature of the DH). The use of the algorithm implemented in the MatLab package ensures the solution of the optimisation problem in real time by a gradient-free stepwise method using one-dimensional extremum search methods. The technical structure of a computer-integrated system for optimal software control of the temperature regime of a low-temperature evaporator, adapted to the existing information system of an industrial synthesis unit, has been determined.
- 11 November 2025
- Published by Private Company Technology Center
Open AccessChapter 1. Technological aspects of computer control of the secondary condensation complex of ammonia production under uncertainty
The object of study is a technological complex of secondary condensation (TCS) of large-capacity ammonia synthesis units of AM-1360 series, which provides final cooling and separation of condensed product ammonia from circulating gas (CG). The possibility of increasing the energy efficiency of production by modernising the equipment and technological design of the TACC was established. This is achieved by removing an energy-intensive electrically driven turbo-compressor refrigeration unit (TCRU) from the scheme and creating an adaptive system of optimal software control. The expediency of applying a systematic approach to solving such a complex problem, the scientific basis of which is mathematical modelling and process identification, is shown. The peculiarities of the operating conditions of the TKVK and the primary condensation unit are analysed. The research results revealed uncertainties in the functioning of such components as the condensing column (CC) and low-temperature evaporators (LTE), which are connected to the operation scheme of two absorption-cooling units (ACU) and the ATC. The algorithms for generating an information array of experimental data and numerical estimation of uncertainties, in particular, heat transfer coefficients in the BF and LST, as well as ammonia concentration at the outlet of the primary condensation unit and the BF, were developed. The algorithms provide for the separation of transient modes in the operation of the TKVK, verification of stationarity, reproducibility of the process and the hypothesis of the normality of the empirical distribution, which makes it possible to use a stochastic approximation method for numerical estimation of uncertainties. Based on the results of processing the experimental data, a discrepancy between the real and design heat transfer coefficients was found, which is due to an underestimation of the condensation thermal resistance. The heat transfer processes in the BF and CNT as part of the CCS were identified and equations were obtained to determine the heat transfer coefficients, heat transfer, condensation thermal resistance, and ammonia concentration in the GHG at the inlet and outlet of the BF. The conditions of the required temperature distribution in the TCWC to exclude it from the ATC scheme and reduce the DH cooling temperature in the HST by 5 °C compared to the original variant at the maximum DH heat load at the inlet of the complex were determined by mathematical modelling. The developed scheme of the TACC is characterised by greater energy efficiency due to the use of only heat-using refrigeration systems of AHU and steam generating units (SGU), which utilise the heat of material flows of both low temperature potential (up to 150 °C) and ultra-low (up to 90 °C). Using the method of mathematical modelling of the VNT, the regularity of the extreme nature of the dependence of the cooling capacity and cooling temperature of the DH on the phlegm flow rate was established. The achievement of the maximum cooling capacity, and hence the minimum cooling temperature of the DH at a certain temperature head, is due to the critical mode of bubble boiling of the refrigerant. The dependencies of the DH cooling temperature on the controlling effect of the phlegm flow rate are determined, which characterise the shift of the extremum under conditions of changing the coordinates of the perturbation vector, and hence the change in the energy efficiency of ammonia production (annual natural gas consumption). Algorithmic software was developed to solve the problems of identification, obtaining a mathematical model of the CNT evaporator and numerical estimation of the optimal state vector (cooling temperature of the DH). The use of the algorithm implemented in the MatLab package ensures the solution of the optimisation problem in real time by a gradient-free stepwise method using one-dimensional extremum search methods. The technical structure of a computer-integrated system for optimal software control of the temperature regime of a low-temperature evaporator, adapted to the existing information system of an industrial synthesis unit, has been determined.
- Open Access
- 17 June 2025
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI" A series of "Information and Modeling"
- Vol. 1 (1 (13)) , 35-46
Determination of the structure of the control system for the technological complex of secondary condensation of ammonia production
The conditions of functioning of the technological complex of secondary condensation of ammonia production are studied, which allowed to establish the nature of uncertainties. The expediency of using a stochastic method of their calculation for identifying and creating mathematical models of heat exchangers is substantiated. The necessity of using an adaptive system of optimal software control to minimise and stabilise the temperature regime in the devices of the complex is determined.
- 17 June 2025
- Published by National Technical University Kharkiv Polytechnic Institute in Bulletin of the National Technical University "KhPI" A series of "Information and Modeling"
- Vol. 1 (1 (13)) , 35-46
Open AccessDetermination of the structure of the control system for the technological complex of secondary condensation of ammonia production
The conditions of functioning of the technological complex of secondary condensation of ammonia production are studied, which allowed to establish the nature of uncertainties. The expediency of using a stochastic method of their calculation for identifying and creating mathematical models of heat exchangers is substantiated. The necessity of using an adaptive system of optimal software control to minimise and stabilise the temperature regime in the devices of the complex is determined.
- Open Access
- 14 May 2024
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 3 (2(77)) , 49-52
Creation of an identifier database for the ammonia synthesis computer control system
The object of research is the control system of the synthesis department of the large-tonnage ammonia production unit of the AM-1360 series. An analysis of the functioning conditions of the synthesis department was carried out. The significant influence of the content of inerts in the synthesis cycle on the energy efficiency of ammonia production is shown, the optimal value of which depends both on the accepted level of prices for energy carriers and on the method of using purge gases. The need to create a computer-integrated control technology to optimize the use of purge gases is established. The function of the identifier of such a control technology is defined, namely, continuous refinement based on current information about the state of the main sections of the synthesis department, such as the synthesis column, primary and secondary condensation. The operation of these stations takes place in the conditions of seasonal and daily changes in the heat load, which causes parametric uncertainty of such parameters of the connection of the mathematical model as the concentration of ammonia in the circulating gas at the outlet of the stations listed above. Numerical assessment of these uncertainties according to the results of analytical studies for such technological objects is most often performed using stochastic approximation methods. Let’s note that the significant inertia of the objects of the synthesis department under certain conditions makes it impossible to adapt the parameter to its actual value. An algorithmic base has been created for the formation of an information array of the identifier of the computer-integrated control technology of the ammonia synthesis department, which ensures the separation of transient modes under conditions of uncertainty and allows to perform the task of identifying processes in the synthesis column, in the primary and secondary condensation units. The proposed algorithm allows to perform convergence in the department both on the general and on the component material balances. The algorithm is implemented in the MatLab application program package and tested by means of simulation based on experimental data of industrial operation of AM-1360 series ammonia synthesis units.
- 14 May 2024
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 3 (2(77)) , 49-52
Open AccessCreation of an identifier database for the ammonia synthesis computer control system
The object of research is the control system of the synthesis department of the large-tonnage ammonia production unit of the AM-1360 series. An analysis of the functioning conditions of the synthesis department was carried out. The significant influence of the content of inerts in the synthesis cycle on the energy efficiency of ammonia production is shown, the optimal value of which depends both on the accepted level of prices for energy carriers and on the method of using purge gases. The need to create a computer-integrated control technology to optimize the use of purge gases is established. The function of the identifier of such a control technology is defined, namely, continuous refinement based on current information about the state of the main sections of the synthesis department, such as the synthesis column, primary and secondary condensation. The operation of these stations takes place in the conditions of seasonal and daily changes in the heat load, which causes parametric uncertainty of such parameters of the connection of the mathematical model as the concentration of ammonia in the circulating gas at the outlet of the stations listed above. Numerical assessment of these uncertainties according to the results of analytical studies for such technological objects is most often performed using stochastic approximation methods. Let’s note that the significant inertia of the objects of the synthesis department under certain conditions makes it impossible to adapt the parameter to its actual value. An algorithmic base has been created for the formation of an information array of the identifier of the computer-integrated control technology of the ammonia synthesis department, which ensures the separation of transient modes under conditions of uncertainty and allows to perform the task of identifying processes in the synthesis column, in the primary and secondary condensation units. The proposed algorithm allows to perform convergence in the department both on the general and on the component material balances. The algorithm is implemented in the MatLab application program package and tested by means of simulation based on experimental data of industrial operation of AM-1360 series ammonia synthesis units.
- Open Access
- 28 February 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (2 (127)) , 74-81
Designing energy-efficient hardware and technological structure of absorption refrigeration units for ammonia production
The object of research is the equipment and technological design of absorption refrigeration units (ARUs) for the technological system of secondary condensation of large-scale ammonia production. Improving the energy efficiency of ARU is an urgent problem in the general process of reducing operating costs for natural gas in these industries as a whole. Based on the results of analytical studies, the feasibility of combining absorption-refrigeration and vapor-ejector cycles was substantiated, which ensures a decrease in the boiling temperature of a weak water-ammonia solution in the cube of the generator-rectifier and an increase in the condensation pressure in the ARU cycle. Under such circumstances, it becomes possible to increase the concentration of the refrigerant due to the rectification of steam with a part of the liquid refrigerant without using a pump with the removal of the dephlegmator from the ARU circuit. Experimental studies and material-thermal calculations of ARU cycles were carried out to determine the basis of comparison and the proposed version of the ARU scheme. It has been proven that the new technological design of ARU provides an increase in cooling capacity from 3.22 MW to 3.6 MW (by 12 %), the thermal coefficient from 0.527 to 0.551 (by 4.6 %), a decrease in the circulation ratio from 7.77 to 7.1 (by 8 %), and a decrease in the secondary condensation temperature by 2.5 ℃. It is shown that for the proposed version of the technological design of ARU, there is a change in specific costs – an increase in electricity by 1.48 kWh/t NH3 and a decrease in natural gas by 0.41 nm3/t NH3. Taking into account existing cost indicators for natural gas and electricity, the application of the proposed technology ensures a decrease in annual operating costs by UAH 7 million (USD 185,000), and therefore an increase in the economy of ammonia production as a whole Об’єктом досліджень є апаратурно-технологічне оформлення абсорбційно-холодильних установок (АХУ) технологічного комплексу вторинної конденсації великотоннажних виробництв аміаку. Підвищення енергоефективності АХУ становить актуальну проблему у загальному процесі зниження експлуатаційних витрат по природному газу цих виробництв в цілому. За результатами аналітичних досліджень обґрунтована доцільність поєднання абсорбційно-холодильного та пароежекторного циклів, що забезпечує зниження температури кипіння слабкого водоаміачного розчину в кубі генератора-ректифікатора та підвищення тиску конденсації в циклі АХУ. За таких обставин з'являється можливість збільшення концентрації холодоагенту за рахунок ректифікації пари частиною рідкого холодоагенту без застосування насосу із вилученням зі схеми АХУ дефлегматора. Проведено експериментальні дослідження та матеріально-теплові розрахунки циклів АХУ з визначенням бази порівняння та запропонованого варіанту схеми АХУ. Доведено, що нове технологічне оформлення АХУ забезпечує збільшення холодопродуктивності з 3,22 МВт до 3,6 МВт (на 12 %), теплового коефіцієнту з 0,527 до 0,551 (на 4,6 %), зниження кратності циркуляції з 7,77 до 7,1 (на 8 %) та зниження температури вторинної конденсації на 2,5 ℃. Показано, що для запропонованого варіанту технологічного оформлення АХУ спостерігається зміна питомих витрат – збільшення по електроенергії на 1,48 кВтгод/т NH3 та зниження по природному газу на 0,41 нм3/т.NH3. Враховуючи існуючі вартісні показники по природному газу і електроенергії застосування запропонованої технології забезпечує зниження річних експлуатаційних витрат на 7 млн грн.($185000), а отже і підвищення економічності виробництва аміаку в цілому
- 28 February 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (2 (127)) , 74-81
Open AccessDesigning energy-efficient hardware and technological structure of absorption refrigeration units for ammonia production
The object of research is the equipment and technological design of absorption refrigeration units (ARUs) for the technological system of secondary condensation of large-scale ammonia production. Improving the energy efficiency of ARU is an urgent problem in the general process of reducing operating costs for natural gas in these industries as a whole. Based on the results of analytical studies, the feasibility of combining absorption-refrigeration and vapor-ejector cycles was substantiated, which ensures a decrease in the boiling temperature of a weak water-ammonia solution in the cube of the generator-rectifier and an increase in the condensation pressure in the ARU cycle. Under such circumstances, it becomes possible to increase the concentration of the refrigerant due to the rectification of steam with a part of the liquid refrigerant without using a pump with the removal of the dephlegmator from the ARU circuit. Experimental studies and material-thermal calculations of ARU cycles were carried out to determine the basis of comparison and the proposed version of the ARU scheme. It has been proven that the new technological design of ARU provides an increase in cooling capacity from 3.22 MW to 3.6 MW (by 12 %), the thermal coefficient from 0.527 to 0.551 (by 4.6 %), a decrease in the circulation ratio from 7.77 to 7.1 (by 8 %), and a decrease in the secondary condensation temperature by 2.5 ℃. It is shown that for the proposed version of the technological design of ARU, there is a change in specific costs – an increase in electricity by 1.48 kWh/t NH3 and a decrease in natural gas by 0.41 nm3/t NH3. Taking into account existing cost indicators for natural gas and electricity, the application of the proposed technology ensures a decrease in annual operating costs by UAH 7 million (USD 185,000), and therefore an increase in the economy of ammonia production as a whole Об’єктом досліджень є апаратурно-технологічне оформлення абсорбційно-холодильних установок (АХУ) технологічного комплексу вторинної конденсації великотоннажних виробництв аміаку. Підвищення енергоефективності АХУ становить актуальну проблему у загальному процесі зниження експлуатаційних витрат по природному газу цих виробництв в цілому. За результатами аналітичних досліджень обґрунтована доцільність поєднання абсорбційно-холодильного та пароежекторного циклів, що забезпечує зниження температури кипіння слабкого водоаміачного розчину в кубі генератора-ректифікатора та підвищення тиску конденсації в циклі АХУ. За таких обставин з'являється можливість збільшення концентрації холодоагенту за рахунок ректифікації пари частиною рідкого холодоагенту без застосування насосу із вилученням зі схеми АХУ дефлегматора. Проведено експериментальні дослідження та матеріально-теплові розрахунки циклів АХУ з визначенням бази порівняння та запропонованого варіанту схеми АХУ. Доведено, що нове технологічне оформлення АХУ забезпечує збільшення холодопродуктивності з 3,22 МВт до 3,6 МВт (на 12 %), теплового коефіцієнту з 0,527 до 0,551 (на 4,6 %), зниження кратності циркуляції з 7,77 до 7,1 (на 8 %) та зниження температури вторинної конденсації на 2,5 ℃. Показано, що для запропонованого варіанту технологічного оформлення АХУ спостерігається зміна питомих витрат – збільшення по електроенергії на 1,48 кВтгод/т NH3 та зниження по природному газу на 0,41 нм3/т.NH3. Враховуючи існуючі вартісні показники по природному газу і електроенергії застосування запропонованої технології забезпечує зниження річних експлуатаційних витрат на 7 млн грн.($185000), а отже і підвищення економічності виробництва аміаку в цілому
- Open Access
- 30 June 2022
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 3 (2(65)) , 41-44
Development of hardware and software support of computer-integrated technology of complex of secondary condensation of ammonia production
The object of research is the technological complex of secondary condensation (TCSC) and the control system of a typical ammonia synthesis unit of the AM-1360 series. The analysis of the conditions of its functioning and hardware and technological design was carried out. The coordinates of the control vector are determined. The features of the proposed functional diagram and the necessary algorithmic software for the computer-integrated control technology of the TCSC with a correction subsystem for decision-making under uncertainty are established. The implementation of the proposed solutions is complicated by the use of the information and control complex TDC-300 (USA) with closed-type software installed on the existing ammonia synthesis units. The need for such a control complex to implement a decision-making subsystem under conditions of uncertainty is shown to supplement the existing control system with hardware and software of an «open» type. A computer-integrated TCSC technology based on a three-level hierarchical structure has been created. The implementation of the zero and first levels of such a structure form single software and hardware complex consisting of a programmable logic controller and an automated operator's workplace based on an industrial computer with installed software. A software implementation of decision-making on the correction of the coordinates of the control vector by additional hardware and software based on the VIPA logic controller and the Zenon SCADA system was made. A scheme of network information flows has been implemented, which illustrates the functioning of the decision-making correction subsystem in the general structure of the TCSC computer-integrated control technology. Implementation of the developed system allows, under the existing uncertainties, to reduce the secondary condensation temperature by an average of 3 °C, which ensures an annual reduction in natural gas consumption by 1 million nm3. The proposed approach to the possibility of combining «open» and «closed» type hardware and software can be applied in other industries.
- 30 June 2022
- Published by Private Company Technology Center in Technology audit and production reserves
- Vol. 3 (2(65)) , 41-44
Open AccessDevelopment of hardware and software support of computer-integrated technology of complex of secondary condensation of ammonia production
The object of research is the technological complex of secondary condensation (TCSC) and the control system of a typical ammonia synthesis unit of the AM-1360 series. The analysis of the conditions of its functioning and hardware and technological design was carried out. The coordinates of the control vector are determined. The features of the proposed functional diagram and the necessary algorithmic software for the computer-integrated control technology of the TCSC with a correction subsystem for decision-making under uncertainty are established. The implementation of the proposed solutions is complicated by the use of the information and control complex TDC-300 (USA) with closed-type software installed on the existing ammonia synthesis units. The need for such a control complex to implement a decision-making subsystem under conditions of uncertainty is shown to supplement the existing control system with hardware and software of an «open» type. A computer-integrated TCSC technology based on a three-level hierarchical structure has been created. The implementation of the zero and first levels of such a structure form single software and hardware complex consisting of a programmable logic controller and an automated operator's workplace based on an industrial computer with installed software. A software implementation of decision-making on the correction of the coordinates of the control vector by additional hardware and software based on the VIPA logic controller and the Zenon SCADA system was made. A scheme of network information flows has been implemented, which illustrates the functioning of the decision-making correction subsystem in the general structure of the TCSC computer-integrated control technology. Implementation of the developed system allows, under the existing uncertainties, to reduce the secondary condensation temperature by an average of 3 °C, which ensures an annual reduction in natural gas consumption by 1 million nm3. The proposed approach to the possibility of combining «open» and «closed» type hardware and software can be applied in other industries.
- Open Access
- 25 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (2(115)) , 105-115
Design of an intelligent system to control the technological system of ammonia production secondary condensation
This paper has analyzed the functioning conditions for the technological system of secondary condensation (TSSC) in a typical ammonia synthesis unit of the AM-1360 series with the use of a system-control approach. The coordinates of control vectors and external disturbances have been determined. An algorithm has been developed for predicting the coordinates of the control vector for the subsystem of decision support under the conditions of external disturbances for such a complex inertial object with high metal consumption as TSSC. The method of mathematical modeling was used to determine, based on the developed algorithm, the patterns and quantitative dependences of the influence of external disturbances such as the temperature of primary condensation and the flow rate of circulation gas on the efficiency of TSSC heat exchange processes. The regularity of increase in the heat flows and coordinates of control vector with an increase in the temperature of primary condensation has been established. The parametric sensitivity of the coordinates of the control vector under the conditions of change in the temperature of the primary condensation has been determined, which, compared with the circulation gas flow rate, exceeds it by more than six times. The executed software implementation of the algorithm employing the MATLAB programming environment makes it possible, owing to the embedded client part (ORC client), free software access to the current data on the technological process. The functional structure of computer-integrated TSSC technology with the proposed correction subsystem under a supervisory control mode has been designed. Correction solutions involving the additional hardware and software based on the programmable logic controller VIPA and SCADA-system Zenon have been practically implemented. The implementation of the developed system ensures the stabilization of the secondary condensation temperature at the regulatory level of −5 °C, which reduces the consumption of natural gas by almost 1 million nm3 per year.
- 25 February 2022
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (2(115)) , 105-115
Open AccessDesign of an intelligent system to control the technological system of ammonia production secondary condensation
This paper has analyzed the functioning conditions for the technological system of secondary condensation (TSSC) in a typical ammonia synthesis unit of the AM-1360 series with the use of a system-control approach. The coordinates of control vectors and external disturbances have been determined. An algorithm has been developed for predicting the coordinates of the control vector for the subsystem of decision support under the conditions of external disturbances for such a complex inertial object with high metal consumption as TSSC. The method of mathematical modeling was used to determine, based on the developed algorithm, the patterns and quantitative dependences of the influence of external disturbances such as the temperature of primary condensation and the flow rate of circulation gas on the efficiency of TSSC heat exchange processes. The regularity of increase in the heat flows and coordinates of control vector with an increase in the temperature of primary condensation has been established. The parametric sensitivity of the coordinates of the control vector under the conditions of change in the temperature of the primary condensation has been determined, which, compared with the circulation gas flow rate, exceeds it by more than six times. The executed software implementation of the algorithm employing the MATLAB programming environment makes it possible, owing to the embedded client part (ORC client), free software access to the current data on the technological process. The functional structure of computer-integrated TSSC technology with the proposed correction subsystem under a supervisory control mode has been designed. Correction solutions involving the additional hardware and software based on the programmable logic controller VIPA and SCADA-system Zenon have been practically implemented. The implementation of the developed system ensures the stabilization of the secondary condensation temperature at the regulatory level of −5 °C, which reduces the consumption of natural gas by almost 1 million nm3 per year.