Yuko Hibi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Yuko Hibi has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Takashi Murakami
Advanced Manufacturing Research Institute, National Institute of Advanced Industrial Science and Technology (AIST)
7 shared publications - Hiroki Mano
National Institute of Advanced Industrial Science and Technology (AIST), Tsukuba, Ibaraki 305-8564, Japan
6 shared publications Shinya Sasaki
National Institute of Advanced Industrial Science and Technology (AIST), Advanced Manufacturing Research Institute, Tsukuba, Ibaraki 305‐8564, Japan
6 shared publicationsYuji Enomoto
4 shared publications- Kunio Matsuzaki
National Institute of Advanced Industrial Science and Technology
3 shared publications Y. Enomoto
Mechanical Engineering Laboratory
3 shared publications
Latest Publications
- 31 May 2019
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 14 (2) , 32-40
Influence of Organic Solvents on Adhesive Wear of Titanium Slid against Ceramics
To determine the titanium adhesion inhibitory effect of organic solvents on the sliding surface between titanium (Ti) and ceramics, Ti disks were slid against silicon nitride (Si3N4) pins under dry conditions, in n-undecane, and in ethanol using a unidirectional pinon-disk machine. Ti disks were also slid against alumina (Al2O3) pins under dry condition and in ethanol. Contour measurement, microstructural observation and chemical analysis of the worn disk and pin surfaces were performed. Under dry conditions, the substances composed of Ti adhered to the whole of the wear scars of both the Si3N4 pin and Al2O3 pin. n-Undecane and ethanol inhibited the adhesion of Ti to the Si3N4 pin effectively. Tribochemical reaction products seemed to contribute to the wear of the Si3N4 pin/Ti disk pair in n-undecane and in ethanol. The amount of adhesion of Ti to the Al2O3 pin was less in ethanol than under dry conditions. Mechanical wear such as fracture and cutting seemed to be main wear mechanisms of the Al2O3 pin/Ti disk pair in ethanol. Wear of the Ti disk in ethanol was significantly affected by the surface roughness of the wear scar of the mating ceramic pin.
- 31 May 2019
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 14 (2) , 32-40
Influence of Organic Solvents on Adhesive Wear of Titanium Slid against Ceramics
To determine the titanium adhesion inhibitory effect of organic solvents on the sliding surface between titanium (Ti) and ceramics, Ti disks were slid against silicon nitride (Si3N4) pins under dry conditions, in n-undecane, and in ethanol using a unidirectional pinon-disk machine. Ti disks were also slid against alumina (Al2O3) pins under dry condition and in ethanol. Contour measurement, microstructural observation and chemical analysis of the worn disk and pin surfaces were performed. Under dry conditions, the substances composed of Ti adhered to the whole of the wear scars of both the Si3N4 pin and Al2O3 pin. n-Undecane and ethanol inhibited the adhesion of Ti to the Si3N4 pin effectively. Tribochemical reaction products seemed to contribute to the wear of the Si3N4 pin/Ti disk pair in n-undecane and in ethanol. The amount of adhesion of Ti to the Al2O3 pin was less in ethanol than under dry conditions. Mechanical wear such as fracture and cutting seemed to be main wear mechanisms of the Al2O3 pin/Ti disk pair in ethanol. Wear of the Ti disk in ethanol was significantly affected by the surface roughness of the wear scar of the mating ceramic pin.
- 1 January 2018
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 13 (2) , 57-66
Tribological Behavior of Polyethylene/Light Metal Pairs in Low Viscosity Organic Solvents
- 1 January 2018
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 13 (2) , 57-66
Tribological Behavior of Polyethylene/Light Metal Pairs in Low Viscosity Organic Solvents
- 12 September 2013
- Published by Elsevier in Tribology International
- Vol. 69, 61-69
Friction and wear properties of αFeSi2–Si alloy, ReSi1.8 and MoSi2 in ethyl alcohol
- 12 September 2013
- Published by Elsevier in Tribology International
- Vol. 69, 61-69
Friction and wear properties of αFeSi2–Si alloy, ReSi1.8 and MoSi2 in ethyl alcohol
- 1 December 2012
- Published by Elsevier in Tribology International
- Vol. 56, 1-8
Friction and wear properties of Fe7Mo6- and αFeSi2-based alloys in rapeseed oil
- 1 December 2012
- Published by Elsevier in Tribology International
- Vol. 56, 1-8
Friction and wear properties of Fe7Mo6- and αFeSi2-based alloys in rapeseed oil
- Open Access
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2012, _S114031-1
S114031 Lubricity of Triolein and Tristearin under High Temperature Condition
We investigated difference of lubricity of triolein, tristearin and rapeseed oil as a reference under high temperature conditions for acceleration of oxidation degradation. Though the triolein consisting of the monounsaturated fatty acid showed superior oxidation durability and oiliness to the rapeseed oil including the polyunsaturated fatty acid, phenomena which might be caused by corrosion and elimination of adsorbed film were observed on both lubricants. On the other hand, there was a possibility that the tristearin consisting of the saturated fatty acid has a superior forming capability of adsorbed film and not be related to corrosion.
- 1 January 2012
- Published by Japan Society of Mechanical Engineers in The Proceedings of Mechanical Engineering Congress, Japan
- Vol. 2012, _S114031-1
Open AccessS114031 Lubricity of Triolein and Tristearin under High Temperature Condition
We investigated difference of lubricity of triolein, tristearin and rapeseed oil as a reference under high temperature conditions for acceleration of oxidation degradation. Though the triolein consisting of the monounsaturated fatty acid showed superior oxidation durability and oiliness to the rapeseed oil including the polyunsaturated fatty acid, phenomena which might be caused by corrosion and elimination of adsorbed film were observed on both lubricants. On the other hand, there was a possibility that the tristearin consisting of the saturated fatty acid has a superior forming capability of adsorbed film and not be related to corrosion.
- 1 October 2011
- Published by Elsevier in Intermetallics
- Vol. 20 (1) , 68-75
Friction and wear properties of Fe–Si intermetallic compounds in ethyl alcohol
- 1 October 2011
- Published by Elsevier in Intermetallics
- Vol. 20 (1) , 68-75
Friction and wear properties of Fe–Si intermetallic compounds in ethyl alcohol
- 1 November 2010
- Published by Elsevier in Tribology International
- Vol. 43 (11) , 2183-2189
Friction and wear properties of Fe7Mo6-based alloy in ethyl alcohol
- 1 November 2010
- Published by Elsevier in Tribology International
- Vol. 43 (11) , 2183-2189
Friction and wear properties of Fe7Mo6-based alloy in ethyl alcohol
- 1 January 2009
- Published by Springer Nature
- p. 376-377
Friction and Wear Properties of Fe7Mo6-Based Alloy under the Lubrication of Ethyl-Alcohol
- 1 January 2009
- Published by Springer Nature
- p. 376-377
Friction and Wear Properties of Fe7Mo6-Based Alloy under the Lubrication of Ethyl-Alcohol
- Open Access
- 1 January 2009
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 4 (1) , 31-35
Micro-Hole Drilling on Silicon Nitride Ceramics in Ethanol
- 1 January 2009
- Published by Japanese Society of Tribologists in Tribology Online
- Vol. 4 (1) , 31-35
Open AccessMicro-Hole Drilling on Silicon Nitride Ceramics in Ethanol
- 17 January 2008
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 91 (2) , 508-513
Influence of Microstructure on the Wear Behavior of SiC‐Reinforced Titanium‐Matrix Composites Lubricated by Water and by Ethanol
Two kinds of SiC‐reinforced titanium‐matrix composites were slid against themselves in water and in ethanol to evaluate the influence of their microstructure on the wear behavior. The composites had a structure in which the SiC particles were coated with interfacial layers that consisted of Ti 5 Si 3 C x and TiC, and the TiC particles were dispersed in a titanium matrix. The wear resistance of the composites was much better than that of titanium metal. The wear of the composites prepared from starting materials with a high SiC content was lower than that with a low SiC content.
- 17 January 2008
- Published by Wiley in Journal of the American Ceramic Society
- Vol. 91 (2) , 508-513
Influence of Microstructure on the Wear Behavior of SiC‐Reinforced Titanium‐Matrix Composites Lubricated by Water and by Ethanol
Two kinds of SiC‐reinforced titanium‐matrix composites were slid against themselves in water and in ethanol to evaluate the influence of their microstructure on the wear behavior. The composites had a structure in which the SiC particles were coated with interfacial layers that consisted of Ti 5 Si 3 C x and TiC, and the TiC particles were dispersed in a titanium matrix. The wear resistance of the composites was much better than that of titanium metal. The wear of the composites prepared from starting materials with a high SiC content was lower than that with a low SiC content.