ВКВладимир Захарович Ковалев

Владимир Захарович Ковалев

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Владимир Захарович Ковалев has a total of 68 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Development and research of a full-order observer for the dynamic system «cable line – permanent magnet synchronous motor» in discrete time

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Владимир Анатольевич Копырин, Rustam N. Khamitov, Vladimir Z. Kovalev, Александр Александрович Филипас, Alexander A. Shchipkov, Yulia O. Kulesh, Семен Семенович Попов, Евгений Владимирович Боловин, et al.

    Relevance. Currently, the share of centrifugal electric pumps operating in intermittent modes is increasing, allowing for increased oil production from low- and medium-flow wells. This is achieved by switching the well to two-position control modes with separate pumping and fluid accumulation cycles. However, this significantly reduces the time it takes to bring the well up to operating mode, which can reach several minutes. This approach reduces the mean time between failures of submersible electric motors and components of the submersible section of the unit due to increased vibration amplitude and torsional oscillations compared to quasi-stationary processes during continuous well operation. The impact of starting currents and torques, which lead to excessive fatigue wear of the submersible section components, can be reduced by using closed-loop sensorless control systems for submersible electric motor drives. This necessitates the development of methods for identifying unmeasured state variables of submersible electric motors, such as the flux vector and rotor angular velocity, using full-order state observers. Aim. Development and research of a rotor speed and load torque full-order observer for the dynamic system «cable line – permanent magnet synchronous motor» based on explicit mathematical models in discrete time for the implementation of closed-loop sensorless control systems for the electric drive of centrifugal electric pump units. Methods. The work used methods of system analysis and structural-parametric synthesis of dynamic systems, methods of identifying unmeasured state variables of dynamic systems based on state observers, methods of numerical mathematical modeling of dynamic systems described by systems of stiff differential equations, and methods of solving systems of nonlinear algebraic equations. Results. The authors have developed the adaptive mathematical model of a rotor speed and load torque full-order observer for the dynamic system «cable line – permanent magnet synchronous motor». The observer performance was studied under typical operating conditions and when the parameters of its customizable model deviated from the reference values. For all operating conditions, the relative errors in estimating the rotor angular velocity and shaft drag torque were less than 1.5 and 1%, respectively.

  • Open Access

    Improving low-level plant control systems ESP models in conditions of oil well conversion to periodic operating modes

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Владимир Анатольевич Копырин, Rustam N. Khamitov, Vladimir Z. Kovalev, Александр Александрович Филипас, Семен Семенович Попов, Евгений Владимирович Боловин, Evgeniia A. Beliauskene, Евгения Александровна Беляускене

    Relevance. Currently, the majority of oil production is carried out using centrifugal electric pumps, and the share of installations operating in periodic modes with cycles of accumulation and pumping of liquid is increasing every year. At the same time, the latest studies of the reliability of their components show that the mean time between failures of submersible equipment is reduced to 2.5 times compared to equipment in continuous operation modes. The decrease in reliability is associated with the dynamics of transient processes in automated lower-level control systems, which is currently not taken into account when developing management decisions to optimize well operation, and the entire lower-level subsystem, as a rule, is represented by linear or nonlinear static links. This approach does not allow controlling the dynamics of processes within the subsystem itself in the conditions of wells being transferred to intermittent operating modes. This determines the relevance of developing dynamic models of the submersible pump electric drive subsystem in order to optimize transient processes according to the criterion of the time between failures of submersible equipment elements. Aim. Improving models of lower-level automated control systems for a submersible electric motor of a centrifugal electric pump installation for oil production under conditions of switching a well to periodic operation mode in order to improve controllability. Methods. Methods of system analysis and structural-parametric synthesis of automated control systems of technological processes, methods of designing vector control systems for electric drives, methods of identifying state variables based on observers using explicit mathematical models, methods of parametric identification of customizable models of non-stationary dynamic systems. Results. The authors have proposed the approach to constructing an operational control level for centrifugal electric pump installations, including the introduction of closed sensorless electric drive systems using state observers based on explicit adjustable mathematical models of the non-stationary dynamic system "long cable – submersible adjustable electric machine" and methods of their dynamic identification, creating prerequisites for further formulation and solution of problems of optimizing dynamic processes within the lower-level subsystem under conditions of transferring the well to intermittent operating modes. A transition to dynamic models of automated lower-level control systems based on reduced mathematical models of the electrical subsystem of centrifugal electric pump installations is proposed for increasing controllability and taking into account the physical limitations of available measuring instruments.


  • Open Access

    Nonlinear Algebraic Parameter Estimation of Doubly Fed Induction Machine Based on Rotor Current Falling Curves

    by Alexander Glazyrin, Dmitriy Bunkov, Evgeniy Bolovin, Yusup Isaev, Vladimir Kopyrin, Sergey Kladiev, Alexander Filipas, Sergey Langraf, Rustam Khamitov, Vladimir Kovalev, et al.

    Currently, wind turbines utilize doubly fed induction machines that incorporate a frequency converter in the rotor circuit to manage slip energy. This setup ensures a stable voltage amplitude and frequency that align with the alternating current. It is crucial to accurately determine the parameters of the equivalent circuit from the rotor side of the vector control system of the frequency converter. The objective of this study is to develop a method for the preliminary identification of the doubly fed induction machines parameters by analyzing the rotor current decay curves using Newton’s method. The numerical estimates of the equivalent circuit parameters a doubly fed induction machines with a fixed short-circuited rotor are obtained during the validation of the results on a real plant. It is along with the integral errors of deviation between the experimental rotor current decay curve and the response of the adaptive regression model. The integral errors do not exceed 4% in nearly all sections of the curves. It is considered acceptable in engineering practice. The developed algorithm for the preliminary identification for the parameters of the doubly fed induction machines substitution scheme can be applied with the configuring machines control systems, including a vector control system.


  • Open Access

    Development of an observer of rotor angular velocity and resistance moment on the shaft of an adjustable permanent magnet synchronous motor powered through long cable

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Владимир Анатольевич Копырин, Семен Семенович Попов, Евгений Владимирович Боловин, Владимир Захарович Ковалев, Rustam N. Khamitov, Вадим Владимирович Тимошкин

    Relevance. Currently, when using submersible electric motors in centrifugal electric pump installations in cyclic operation mode, there is a reduction in the inter-repair period of submersible equipment, which is associated with a reduction in oil pumping periods to several minutes. As a result, there is a multiple increase in starting currents and torque, which leads to an increase in mechanical loads on the pump shaft and appearance of resonance phenomena during the electric motor acceleration, reducing the reliability of a seal protection. To solve these problems, it is necessary to synthesize closed-loop vector control systems with current and electromagnetic torque control in transient responses. Open-loop scalar control systems for electric drives of oil well production are used in operation, which is due to the complexity of obtaining feedback signals on the angular velocity of the rotor and the moment of resistance on the shaft by means of submersible telemetry. This problem determines the relevance and necessity of developing observers for rotor speed and load torque estimation, taking into account the features of the technological process of installing centrifugal electric pumps, in particular, the presence of a long cable for powering a submersible electric motor based on a synchronous machine with permanent magnets. Aim. To develop a full-order observer rotor speed and load torque for the dynamic system "long supply cable – synchronous motor with permanent magnets". Methods. System analysis and identification of dynamic systems, synthesis of Luenberger observers, mathematical modeling of dynamic systems, electric drives and electrical machines. Result and conclusions. The authors have proposed the mathematical model of a rotor speed and load torque full-order observer for the dynamic system "long supply cable – synchronous motor with permanent magnets". The performance of the observer was investigated under varying load on the shaft, mismatch of non-zero initial conditions, deviation of the parameters of the equivalent circuit of the observer and the object in the range from –20 to +20% of the nominal values.


  • Open Access

    Сравнительный анализ частотных характеристик вариантов построения цифровых моделей фильтров нижних частот компонентов электротехнических комплексов

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Семен Семенович Попов, Владимир Анатольевич Копырин, Сергей Николаевич Кладиев, Андрей Петрович Леонов, Наталья Алексеевна Воронина, Владимир Захарович Ковалев

    Применение цифровых двойников в задачах управления электроприводами обусловлено постоянно возрастающими требованиями к качеству переходных процессов. Цифровой двойник динамической системы представляет собой дискретную модель, применение которой всегда влечет за собой некоторую потерю точности и появление искажений в частотной области. Математические модели кабельных линий характеризуются относительно малыми постоянными времени, что накладывает условия на выбор частоты дискретизации согласно требованиям, предъявляемым теоремой Котельникова–Шеннона. Однако на практике выбор периода дискретизации ограничивается вычислительной мощностью цифрового сигнального процессора. Вследствие этого целью статьи является определение границ применимости в частотной области существующих способов перехода в Z-область методом аналоговых прототипов путем проведения сравнительного анализа погрешности аппроксимации частотных характеристик аналогового прототипа цифровыми моделями RLC-фильтра низких частот для каждого из способов. Установлено, что увеличение периода дискретизации ведет к расхождению между цифровыми моделями и их аналоговыми прототипами в интегральном смысле на всей области частот. Кроме того, это приводит к потере информации о таких физических процессах в реальной системе, как резонанс или изменение фазы сигнала на выходе динамической системы. Для большинства инженерных задач может быть рекомендован метод Тастина при соответствующих допущениях о стационарности динамической системы. Однако при появлении признаков нестационарности или повышенных требованиях к конструированию регуляторов, по мнению авторов, стоит обратить внимание на аналитические модели динамических систем.


  • Open Access

    Desing of an observer with real time monitoring speed and load torque for submersible induction motors

    by Александр Савельевич Глазырин, Семен Семенович Попов, Евгений Игоревич Попов, Владимир Анатольевич Копырин, Rustam N. Khamitov, Александр Александрович Филипас, Вадим Владимирович Тимошкин, Evgeniia A. Beliauskene, Yulia O. Kulesh, Evgeniy V. Bolovin, et al.

    Relevance. When operating submersible equipment for oil production in aggressive environments and transferring wells to the cyclic operation mode, a decrease in the service life of the submersible installation for oil production is observed. In the first case, this is due to the formation of salt deposits and clogging of the working parts of the electric pump with mechanical impurities. In the second case – an increase in the number of starts of the submersible electric motor. To solve the existing problems, it is possible to implement closed control systems for submersible electric motors based on state variable observers, which determines the relevance of the study. Aim. To develop an observer with operational monitoring of the angular velocity of the rotor and the moment of resistance on the shaft of a submersible asynchronous motor at inconsistency of the initial conditions in various operating modes and its testing using modeling tools. Methods. The observer is built on the basis of known engine models in a fixed coordinate system α, β, the theory of IIR-filters to obtain a forecast of estimates of the angular velocity of the rotor and the torque on the shaft and their correction in real time. Results. The authors have proposed the original structure of an observer with operational monitoring of the angular velocity of the rotor and the moment of resistance on the shaft of a submersible asynchronous motor. Conclusions. The paper demonstrates the observer performance with inconsistency of initial conditions and electric motor model data in various operating modes. In all modes, stable estimates of the speed and torque of resistance on the electric motor shaft are obtained. At the same time, the error in estimating the angular velocity under the condition of changing the load on the shaft and starting in the loaded state is no more than 1.2%, which is acceptable in submersible electric motor control systems. It is revealed that the developed observer, under the condition of changing the active resistance of the stator and rotor in the ranges from –25 to +25% of the nominal value, obtains estimates of the angular velocity with an integral error of no more than 5%, except for starting the motor with a decrease in the active resistance of the rotor by 25% of the nominal value –5.53%, which is acceptable in engineering practice.


  • Open Access

    Critical expert analysis of permanent magnet synchronous motors identification methods and state variable observers

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Владимир Анатольевич Копырин, Владимир Захарович Ковалев, Евгений Владимирович Боловин, Семен Семенович Попов, Сергей Николаевич Кладиев, Alexander A. Filipas, Rustam N. Khamitov

    Relevance. In recent years, the oil industry has seen a tendency to transfer low-yield oil wells to intermittent mode. Unregulated electric drive and the open-loop controlled electric drive of electric centrifugal pumping with permanent magnet synchronous motors are typically not suitable for tasks of intermittent operation of wells. Due to objective reasons, there may not be smooth starts and required quality indicators of transient processes, which leads to even more reduction in oil production. The synthesis of a closed-loop electric drive control system of submersible installations is possible only using algorithms for indirect estimation of non-measured mechanical coordinates of the electric drive – state variables identification methods, observers of the rotor angular velocity and the load torque. The installation of sensors of angular velocity and torque on the shaft of the submersible electric motor is associated with technical difficulties, therefore, there is no need for significant modernization of the hardware solutions of the existing electrical equipment system. To date, the theory of identifying non-linear dynamic systems is widely used to derive an indirect estimate of the non-measured state variables of the permanent magnet synchronous motors. The large number of methods presented in scientific sources requires comparative analysis regarding their benefits and disadvantages in order to select the best identification method that meets the requirements of the oil production and takes into account its specificity and features. In this case, identification systems that are focused on minimizing computing power or operating in real time are given priority. Aim. To determine the best in terms of computational complexity and the convenience of practical use method of identifying state variables of permanent magnet synchronous motors operating in submersible oil well pumping units based on comparative analysis of existing methods presented in Russian and foreign sources. Methods. Methods for system analysis and identification of dynamic systems, a method of critical expert analysis. Result and conclusions. The most common methods for identifying and observing the state variables of synchronous motors with permanent magnets have been described in detail, given the general performance of each group of methods, their benefits and disadvantages were reviewed. By comparative critical expert analysis, it was found that for tasks of submersible electric centrifugal pump units electric drive a Luenberger observer, characterized by relatively low computational complexity and ease of setup in engineering practice can be recommended.

  • Open Access

    Сравнительный анализ частотных характеристик вариантов построения цифровых моделей апериодических звеньев компонентов электротехнических комплексов

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Семен Семенович Попов, Владимир Анатольевич Копырин, Сергей Николаевич Кладиев, Андрей Петрович Леонов, Наталья Алексеевна Воронина, Владимир Захарович Ковалев

    Удовлетворение постоянно возрастающих требований к бездатчиковому электроприводу со стороны технологических процессов может быть достигнуто путем применения цифровых двойников, представляющих собой цифровую (дискретную) модель динамической системы. Применение дискретных моделей всегда влечет за собой как некоторую потерю точности во временной области, так и искажения в частотной. Для сохранения точностных свойств модели частота дискретизации должна выбираться из соображений соблюдения требований теоремы Котельникова–Шеннона–Найквиста. Однако на практике выбор периода дискретизации ограничивается вычислительной мощностью цифрового сигнального процессора. Как правило, основным элементом компонентов электротехнических комплексов является апериодическое звено первого порядка. Вследствие этого целью статьи является определение границ применимости в частотной области существующих способов перехода в Z-область методом аналоговых прототипов путем проведения сравнительного анализа интегральной погрешности аппроксимации частотных характеристик аналогового прототипа цифровыми моделями апериодического звена для каждого из способов. Установлено, что увеличение периода дискретизации ведет к расхождению между цифровыми моделями и их аналоговыми прототипами в смысле интегральной погрешности для любой верхней границы окна просмотра в области средних и высоких частот. Это, в свою очередь, приводит к потере информации о таких физических процессах в реальной системе, как диапазон полосы пропускания или изменение фазы сигнала на выходе динамической системы. При соответствующих допущениях о стационарности динамической системы в качестве основного метода построения цифровых моделей для большинства инженерных задач может быть рекомендован метод Тастина. Однако при появлении признаков нестационарности динамической системы или повышенных требованиях к синтезу регуляторов, по мнению авторов, стоит обратить внимание на аналитические модели динамических систем.

  • Open Access

    Analysis of existing approaches to monitoring and diagnostics of the active part of power transformers

    by Olga V. Arkhipova, Vladimir Z. Kovalev, Ruslan V. Saifullin

    Subject of research: monitoring and diagnostics of the condition of the active part of power transformers. Purpose of research: identification of promising trends in the development of methods for monitoring and diagnosing the state of the active part of power transformers. Object of research: power transformers. Methods of research: critical system analysis. Main results of research: the problem of monitoring and diagnosing the condition of the active part of power transformers, including windings, is considered. It is noted that a significant number (more than four million units) of distribution transformers are in operation in the Russian Federation. The causes of emergency failures of the specified class of power transformers are analyzed. One of the main causes of failures is highlighted – a winding circuit in the transformer winding. Attention is focused on the problem of monitoring the state of the active part of the transformer and on the diagnosis of the development of short circuits in the transformer winding. The presence of several groups of methods for monitoring and diagnosing winding circuits of transformer windings is shown. The economic attractiveness of monitoring and diagnostics based on the reaction to artificial electromagnetic influences, and monitoring and diagnostics based on the reaction to natural electromagnetic influences is shown.


  • Open Access

    Analytical model of dynamic system "long cable - submersible induction motor with fixed rotor" in polar coordinate system

    by Александр Савельевич Глазырин, Ivan A. Nabunskiy, Семен Семенович Попов, Евгений Владимирович Боловин, Вадим Владимирович Тимошкин, Сергей Николаевич Кладиев, Alexander A. Filipas, Rustam N. Khamitov, Владимир Анатольевич Копырин, Евгений Игоревич Попов, et al.

    Relevance. The stock of oil wells in the Russian Federation, where production is carried out with the help of electric centrifugal pumps or electric-driven vane pumps, is expanding every year. This trend will continue for at least a couple of decades. In its turn, the number of wells with readily available oil products in the commissioned stock is decreasing. This leads to the need to improve production quality and reduce energy consumption to maintain profitability and production volumes. This can be achieved by implementing vector energy-efficient control systems for submersible motors based on observers of induction motor state variables. In this case one should take into account transients in the supply cable of considerable length, which transmits energy from a frequency converter to a motor. The observers are based on adjustable mathematical models that describe electrical, electromechanical and mechanical processes in electric drive and related process automation systems as reliably as possible. Using complex and cumbersome adjustable mathematical models in digital signal processors due to limited performance and memory causes objective difficulties in obtaining solutions of increased accuracy in real time. On this basis, the development of an analytical model of the dynamic system "long cable – submersible induction motor with fixed rotor" in the polar coordinate system is an urgent task. Aim. Development of analytical description of the mathematical model of the induction motor with a fixed rotor in the polar coordinate system taking into account the influence of a long cable. Methods. Electric drive theory, electric machine theory, mathematical models of submersible induction motors and reduced long cable model, Vandermonde's determinant, analytical methods for solving differential equations. Result and conclusions. The authors have developed an analytical model of the regulated induction motor with a fixed rotor in the polar coordinate system taking into account the supply cable of considerable length. The developed analytical model is recommended for use in vector energy-efficient electric drive with application of phase discrimination principles taking into account the influence of processes in the supply cable line. Such electric drive has a potential for increasing the profitability of oil production from low- and medium-debt wells. Актуальность. Фонд нефтяных скважин Российской Федерации, в которых добыча производится с помощью установок электроцентробежных насосов или электроприводных лопастных насосов с каждым годом расширяется, и такая тенденция будет сохраняться минимум пару десятков лет. В свою очередь количество скважин с легкодоступными нефтепродуктами во введенном в эксплуатацию фонде уменьшается, что приводит к необходимости улучшения качества добычи и уменьшения энергозатрат для сохранения рентабельности и объемов добычи. Добиться этого возможно с помощью внедрения векторных энергоэффективных систем управления погружными двигателями на основе наблюдателей переменных состояния асинхронных электродвигателей с учетом переходных процессов в питающем кабеле значительной длины, передающем энергию от преобразователя частоты к двигателю. Основой наблюдателей являются настраиваемые математические модели, максимально достоверно описывающие электрические, электромеханические и механические процессы в электроприводе и связанных с ним системах автоматизации технологических процессов. Однако применение сложных и громоздких настраиваемых математических моделей в цифровых сигнальных процессорах из-за ограниченности производительности и памяти вызывает объективные трудности в получении решений повышенной точности в реальном масштабе времени. На основании этого разработка аналитической модели динамической системы «длинный кабель – погружной асинхронный двигатель с заторможенным ротором» в полярной системе координат является актуальной задачей. Цель: разработка аналитического описания настраиваемой математической модели регулируемого асинхронного двигателя с заторможенным ротором в полярной системе координат с учетом влияния длинного кабеля. Методы: теория электропривода, теории электрических машин, математические модели погружных асинхронных двигателей и редуцированной модели длинного кабеля, определитель Вандермонда,...