Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Владимир Анатольевич Копырин has a total of 74 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Stationary and non-stationary thermohydraulic processes of liquid in a pipeline with laminar flow

    by A.E. Sidorova, В.с. Гительман, S.S. Golovchenko, V.A. Kopyrin, Yu.N. Isaev

    Relevance. Many branches of engineering require, to varying degrees, the calculation of pipeline systems, the analysis of fluid flow, and the investigation of heat transfer phenomena occurring during fluid motion near solid boundaries. Depending on the fluid viscosity and flow velocity, the flow regime may be laminar or turbulent, which significantly influences the temperature distribution along the pipeline. In oil and gas fields operating under harsh climatic conditions, electric heating systems are widely used for oil, gas, and water pipelines installed on the surface or for individual sections exposed at the surface in well clusters, process facilities, booster pumping stations, preliminary water and gas separation units, compressor stations, and oil collection points. The selection of the electric heating configuration and power is determined by thermal engineering calculations. However, existing engineering approaches are largely based on simplified empirical models and do not adequately account for the coupled interaction of hydrodynamic, thermal, and electrical processes, which leads to increased energy consumption and reduced reliability of fluid and gas transportation. This article presents a calculation of the velocity distribution in the cross-sectional and longitudinal directions of a pipe in order to determine the corresponding temperature distribution. Aim. To determine the fluid velocity distribution in the pipe cross-section and the temperature distribution along the pipe under laminar flow conditions based on the Navier–Stokes equations, the continuity equation, and the heat conduction equation. Methods. Analytical method is employed to solve the Navier–Stokes equations and the continuity equation. Result and conclusions. The authors have obtained the analytical expressions for the fluid velocity distribution in the pipe cross-section for both steady-state and transient laminar flow regimes. The paper demonstrates the effect of the flow regime on the heat transfer coefficient at the fluid–pipe wall interface. The authors determined the Nusselt eigenvalues and eigenfunctions, enabling the fluid temperature field to be represented as a series and the temperature distribution along the pipeline to be calculated. The results can be applied in thermal engineering calculations and in the design of electric heating systems for pipelines.


  • Open Access

    Submersible Compensator of Reactive Power

    by Vladimir Kopyrin, Evgeniy Popov, Alexander Glazyrin, Yusup Isaev, Rustam Khamitov, Marina Deneko, Maxim Kochetygov

    Enhancing the efficiency of mechanized oil production remains a critical objective in the industry. This paper presents a comparative analysis of existing methods aimed at improving the energy efficiency of oil extraction systems, outlining their respective advantages and limitations. A novel approach is proposed, based on the use of a submersible compensator of reactive power to optimize the performance of electric submersible pumps (ESPs). A mathematical model of the ESP’s electrical system is developed to support the proposed method. Theoretical findings are validated by the experimental studies conducted on operational oil wells. Test results demonstrate a reduction in current consumption by 14.5–20% and an improvement in the power factor from 0.62 to 0.96. These outcomes confirm the effectiveness of the proposed solution in enhancing energy efficiency and reducing electrical losses in oil production processes.

  • Open Access

    Development and research of a full-order observer for the dynamic system «cable line – permanent magnet synchronous motor» in discrete time

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Владимир Анатольевич Копырин, Rustam N. Khamitov, Vladimir Z. Kovalev, Александр Александрович Филипас, Alexander A. Shchipkov, Yulia O. Kulesh, Семен Семенович Попов, Евгений Владимирович Боловин, et al.

    Relevance. Currently, the share of centrifugal electric pumps operating in intermittent modes is increasing, allowing for increased oil production from low- and medium-flow wells. This is achieved by switching the well to two-position control modes with separate pumping and fluid accumulation cycles. However, this significantly reduces the time it takes to bring the well up to operating mode, which can reach several minutes. This approach reduces the mean time between failures of submersible electric motors and components of the submersible section of the unit due to increased vibration amplitude and torsional oscillations compared to quasi-stationary processes during continuous well operation. The impact of starting currents and torques, which lead to excessive fatigue wear of the submersible section components, can be reduced by using closed-loop sensorless control systems for submersible electric motor drives. This necessitates the development of methods for identifying unmeasured state variables of submersible electric motors, such as the flux vector and rotor angular velocity, using full-order state observers. Aim. Development and research of a rotor speed and load torque full-order observer for the dynamic system «cable line – permanent magnet synchronous motor» based on explicit mathematical models in discrete time for the implementation of closed-loop sensorless control systems for the electric drive of centrifugal electric pump units. Methods. The work used methods of system analysis and structural-parametric synthesis of dynamic systems, methods of identifying unmeasured state variables of dynamic systems based on state observers, methods of numerical mathematical modeling of dynamic systems described by systems of stiff differential equations, and methods of solving systems of nonlinear algebraic equations. Results. The authors have developed the adaptive mathematical model of a rotor speed and load torque full-order observer for the dynamic system «cable line – permanent magnet synchronous motor». The observer performance was studied under typical operating conditions and when the parameters of its customizable model deviated from the reference values. For all operating conditions, the relative errors in estimating the rotor angular velocity and shaft drag torque were less than 1.5 and 1%, respectively.

  • Open Access

    Improving low-level plant control systems ESP models in conditions of oil well conversion to periodic operating modes

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Владимир Анатольевич Копырин, Rustam N. Khamitov, Vladimir Z. Kovalev, Александр Александрович Филипас, Семен Семенович Попов, Евгений Владимирович Боловин, Evgeniia A. Beliauskene, Евгения Александровна Беляускене

    Relevance. Currently, the majority of oil production is carried out using centrifugal electric pumps, and the share of installations operating in periodic modes with cycles of accumulation and pumping of liquid is increasing every year. At the same time, the latest studies of the reliability of their components show that the mean time between failures of submersible equipment is reduced to 2.5 times compared to equipment in continuous operation modes. The decrease in reliability is associated with the dynamics of transient processes in automated lower-level control systems, which is currently not taken into account when developing management decisions to optimize well operation, and the entire lower-level subsystem, as a rule, is represented by linear or nonlinear static links. This approach does not allow controlling the dynamics of processes within the subsystem itself in the conditions of wells being transferred to intermittent operating modes. This determines the relevance of developing dynamic models of the submersible pump electric drive subsystem in order to optimize transient processes according to the criterion of the time between failures of submersible equipment elements. Aim. Improving models of lower-level automated control systems for a submersible electric motor of a centrifugal electric pump installation for oil production under conditions of switching a well to periodic operation mode in order to improve controllability. Methods. Methods of system analysis and structural-parametric synthesis of automated control systems of technological processes, methods of designing vector control systems for electric drives, methods of identifying state variables based on observers using explicit mathematical models, methods of parametric identification of customizable models of non-stationary dynamic systems. Results. The authors have proposed the approach to constructing an operational control level for centrifugal electric pump installations, including the introduction of closed sensorless electric drive systems using state observers based on explicit adjustable mathematical models of the non-stationary dynamic system "long cable – submersible adjustable electric machine" and methods of their dynamic identification, creating prerequisites for further formulation and solution of problems of optimizing dynamic processes within the lower-level subsystem under conditions of transferring the well to intermittent operating modes. A transition to dynamic models of automated lower-level control systems based on reduced mathematical models of the electrical subsystem of centrifugal electric pump installations is proposed for increasing controllability and taking into account the physical limitations of available measuring instruments.


  • Open Access

    Nonlinear Algebraic Parameter Estimation of Doubly Fed Induction Machine Based on Rotor Current Falling Curves

    by Alexander Glazyrin, Dmitriy Bunkov, Evgeniy Bolovin, Yusup Isaev, Vladimir Kopyrin, Sergey Kladiev, Alexander Filipas, Sergey Langraf, Rustam Khamitov, Vladimir Kovalev, et al.

    Currently, wind turbines utilize doubly fed induction machines that incorporate a frequency converter in the rotor circuit to manage slip energy. This setup ensures a stable voltage amplitude and frequency that align with the alternating current. It is crucial to accurately determine the parameters of the equivalent circuit from the rotor side of the vector control system of the frequency converter. The objective of this study is to develop a method for the preliminary identification of the doubly fed induction machines parameters by analyzing the rotor current decay curves using Newton’s method. The numerical estimates of the equivalent circuit parameters a doubly fed induction machines with a fixed short-circuited rotor are obtained during the validation of the results on a real plant. It is along with the integral errors of deviation between the experimental rotor current decay curve and the response of the adaptive regression model. The integral errors do not exceed 4% in nearly all sections of the curves. It is considered acceptable in engineering practice. The developed algorithm for the preliminary identification for the parameters of the doubly fed induction machines substitution scheme can be applied with the configuring machines control systems, including a vector control system.


  • The influence of discretization methods on the conditionality of the information matrix and the nature of the formation of error hyperspheres in problems of parameter estimation based on a small number of observations

    by Evgeny I. Popov, Alexander S. Glazyrin, Vladimir A. Kopyrin

    The paper considers the issues of application of discrete models of dynamic systems based on multi-step methods for identification and parameter estimation problems based on a small number of observations using the example of a first-order aperiodic unit. The problem of identification of parameters of dynamic systems is relevant in control problems of stationary and non-stationary dynamic systems, for example, in sensorless control systems of synchronous or asynchronous electric drives of submersible centrifugal electric pumps operating in intermittent operation mode. The problem of parameter estimation was solved in the classical formulation of the least squares method without taking into account a priori information about the nature of noise in the measuring channels. It was shown that the accuracy of parameter estimation depends not only on the norm of the interference vector, but also on its orientation relative to the column space of the information matrix, as well as on the condition number of the information matrix. The matrix formation structure and the problem conditionality depend on the selected approximation method of the state variable derivative. It has been clarified that the obtained parameter estimation results require additional post-filtering for use in closed-loop control systems for reasons of stability. According to the obtained results, implicit multi-step methods can be recommended for most engineering applications in the problems of estimating the parameters of linear and nonlinear systems. The highest accuracy of estimating the parameters of the aperiodic link in terms of the moving average for the entire considered section of the simulation was achieved using the Tustin and Milne methods for transition to discrete time, which allowed for a higher degree of conditionality of the problem compared to other methods.


  • The selection of 10 kV overhead line dimensioning at oil and gas fields of Western Siberia

    by Industrial University of Tyumen, Guzel Khmara, Владимир Анатольевич Копырин, Олег Андреевич Степанов, Mikhail Chekardovsky, Liliya Sedelnikova, Llc «Gazprom Proektirovanie», Гузель Азатовна Хмара, Михаил Николаевич Чекардовский

    The purpose of the work is to study and evaluate energy indicators in different sections of the power supply system with mechanical and reactor-thyristor voltage regulators in case of load current instability. To achieve this goal, the method of computer modeling using MatLab software, comparison methods and the theory of automatic control were used in the work. The study of energy indicators in individual sections of the power supply system was carried out in the Matlab environment on the developed block-modular model of a workshop transformer with a capacity of 1 MV∙A and a volt-age of 6/0,4 kV with an active-inductive nature of the load with a phase shift angle of the load current φ = 45 degrees. From the results of the study of energy indicators, it turned out that a controlled dual-band reactor-thyristor voltage regulator, while maintaining the quality of electricity, comprehensively increases energy performance in all sections of the power supply system. Comparative results of the study and their analyses to improve the quality of electricity and energy indicators in different sections of the power supply system with an uncontrolled and controlled voltage regulator showed the need to replace uncontrolled mechanical voltage regulators with a controlled dual-band reactor-thyristor voltage regulator with high speed, high accuracy and the ability to ensure continuous voltage regulation with external and internal changes in electrical parameters.

  • Open Access

    Development of an observer of rotor angular velocity and resistance moment on the shaft of an adjustable permanent magnet synchronous motor powered through long cable

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Владимир Анатольевич Копырин, Семен Семенович Попов, Евгений Владимирович Боловин, Владимир Захарович Ковалев, Rustam N. Khamitov, Вадим Владимирович Тимошкин

    Relevance. Currently, when using submersible electric motors in centrifugal electric pump installations in cyclic operation mode, there is a reduction in the inter-repair period of submersible equipment, which is associated with a reduction in oil pumping periods to several minutes. As a result, there is a multiple increase in starting currents and torque, which leads to an increase in mechanical loads on the pump shaft and appearance of resonance phenomena during the electric motor acceleration, reducing the reliability of a seal protection. To solve these problems, it is necessary to synthesize closed-loop vector control systems with current and electromagnetic torque control in transient responses. Open-loop scalar control systems for electric drives of oil well production are used in operation, which is due to the complexity of obtaining feedback signals on the angular velocity of the rotor and the moment of resistance on the shaft by means of submersible telemetry. This problem determines the relevance and necessity of developing observers for rotor speed and load torque estimation, taking into account the features of the technological process of installing centrifugal electric pumps, in particular, the presence of a long cable for powering a submersible electric motor based on a synchronous machine with permanent magnets. Aim. To develop a full-order observer rotor speed and load torque for the dynamic system "long supply cable – synchronous motor with permanent magnets". Methods. System analysis and identification of dynamic systems, synthesis of Luenberger observers, mathematical modeling of dynamic systems, electric drives and electrical machines. Result and conclusions. The authors have proposed the mathematical model of a rotor speed and load torque full-order observer for the dynamic system "long supply cable – synchronous motor with permanent magnets". The performance of the observer was investigated under varying load on the shaft, mismatch of non-zero initial conditions, deviation of the parameters of the equivalent circuit of the observer and the object in the range from –20 to +20% of the nominal values.


  • Open Access

    Сравнительный анализ частотных характеристик вариантов построения цифровых моделей фильтров нижних частот компонентов электротехнических комплексов

    by Александр Савельевич Глазырин, Евгений Игоревич Попов, Семен Семенович Попов, Владимир Анатольевич Копырин, Сергей Николаевич Кладиев, Андрей Петрович Леонов, Наталья Алексеевна Воронина, Владимир Захарович Ковалев

    Применение цифровых двойников в задачах управления электроприводами обусловлено постоянно возрастающими требованиями к качеству переходных процессов. Цифровой двойник динамической системы представляет собой дискретную модель, применение которой всегда влечет за собой некоторую потерю точности и появление искажений в частотной области. Математические модели кабельных линий характеризуются относительно малыми постоянными времени, что накладывает условия на выбор частоты дискретизации согласно требованиям, предъявляемым теоремой Котельникова–Шеннона. Однако на практике выбор периода дискретизации ограничивается вычислительной мощностью цифрового сигнального процессора. Вследствие этого целью статьи является определение границ применимости в частотной области существующих способов перехода в Z-область методом аналоговых прототипов путем проведения сравнительного анализа погрешности аппроксимации частотных характеристик аналогового прототипа цифровыми моделями RLC-фильтра низких частот для каждого из способов. Установлено, что увеличение периода дискретизации ведет к расхождению между цифровыми моделями и их аналоговыми прототипами в интегральном смысле на всей области частот. Кроме того, это приводит к потере информации о таких физических процессах в реальной системе, как резонанс или изменение фазы сигнала на выходе динамической системы. Для большинства инженерных задач может быть рекомендован метод Тастина при соответствующих допущениях о стационарности динамической системы. Однако при появлении признаков нестационарности или повышенных требованиях к конструированию регуляторов, по мнению авторов, стоит обратить внимание на аналитические модели динамических систем.