Torsten Lässig
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Torsten Lässig has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Michael May
Fraunhofer Institute for High-Speed Dynamics, Ernst-Mach-Institut, EMI, Freiburg, Germany
6 shared publications Werner Riedel
5 shared publications- Ulrich Heisserer
DSM Dyneema, The Netherlands
4 shared publications - Frank Bagusat
Fraunhofer Institute for High-Speed Dynamics, Ernst-Mach-Institut, EMI, Eckerstrasse 4, 79104 Freiburg, Germany
3 shared publications - Adrian Cirino Orifici
School of Engineering, RMIT University, Carlton, VIC 3001, Australia
2 shared publications Adrian P. Mouritz
2 shared publications
Latest Publications
- 1 August 2018
- Published by Elsevier in Composites Part B: Engineering
- Vol. 147, 47-55
Effect of consolidation pressure on the impact behavior of UHMWPE composites
- 1 August 2018
- Published by Elsevier in Composites Part B: Engineering
- Vol. 147, 47-55
Effect of consolidation pressure on the impact behavior of UHMWPE composites
- 18 December 2017
- Published by DEStech Publications
On the Ultimate Potential of High Strength Polymeric Fibers to Reduce Armor Weight
The capability of polymeric fiber based composites to stop ballistic projectiles at low armor weight is predominantly related to the specific tensile strength of the fibers. This paper and presentation discusses the ultimate theoretical and experimental specific tensile strength of various polymeric fibers (polyethylene, para-aramids, rigid-rods, graphene). It is concluded that the realistic achievable strength of these fiber systems is about half the theoretical strength of single atomic bonds. Ultimate experimental strengths of most fiber systems have reached almost 50 % of this realistic achievable strength. Considering that no defect structures have yet been incorporated in this theoretical strength, it is postulated that these fibers strength can not be increased strongly anymore. Polyethylene fibers, like Dyneema®, have the highest experimental specific fibers strength of all fibers, which would enable a reduction in armor weight by 40% of the current best polyethylene fiber based armor.
- 18 December 2017
- Published by DEStech Publications
On the Ultimate Potential of High Strength Polymeric Fibers to Reduce Armor Weight
The capability of polymeric fiber based composites to stop ballistic projectiles at low armor weight is predominantly related to the specific tensile strength of the fibers. This paper and presentation discusses the ultimate theoretical and experimental specific tensile strength of various polymeric fibers (polyethylene, para-aramids, rigid-rods, graphene). It is concluded that the realistic achievable strength of these fiber systems is about half the theoretical strength of single atomic bonds. Ultimate experimental strengths of most fiber systems have reached almost 50 % of this realistic achievable strength. Considering that no defect structures have yet been incorporated in this theoretical strength, it is postulated that these fibers strength can not be increased strongly anymore. Polyethylene fibers, like Dyneema®, have the highest experimental specific fibers strength of all fibers, which would enable a reduction in armor weight by 40% of the current best polyethylene fiber based armor.
- 1 December 2017
- Published by Elsevier in Composite Structures
- Vol. 182, 590-597
Investigations on the spall and delamination behavior of UHMWPE composites
- 1 December 2017
- Published by Elsevier in Composite Structures
- Vol. 182, 590-597
Investigations on the spall and delamination behavior of UHMWPE composites
- 1 November 2017
- Published by Elsevier in Composite Structures
- Vol. 180, 596-605
Rate-dependent mode I delamination in ballistic composites – Experiment and simulation
- 1 November 2017
- Published by Elsevier in Composite Structures
- Vol. 180, 596-605
Rate-dependent mode I delamination in ballistic composites – Experiment and simulation
- Top Cited Papers
- 1 May 2016
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 84, 224-235
A methodology for hydrocode analysis of ultra-high molecular weight polyethylene composite under ballistic impact
- 1 May 2016
- Published by Elsevier in Composites Part A: Applied Science and Manufacturing
- Vol. 84, 224-235
Top Cited PapersA methodology for hydrocode analysis of ultra-high molecular weight polyethylene composite under ballistic impact
- 1 December 2015
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 86, 240-248
Analysis of the shock response of UHMWPE composites using the inverse planar plate impact test and the shock reverberation technique
- 1 December 2015
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 86, 240-248
Analysis of the shock response of UHMWPE composites using the inverse planar plate impact test and the shock reverberation technique
- Open Access
- 1 January 2015
- Published by Elsevier in Procedia Engineering
- Vol. 103, 436-443
Numerical Modelling of Ultra-High Molecular Weight Polyethylene Composite under Impact Loading
- 1 January 2015
- Published by Elsevier in Procedia Engineering
- Vol. 103, 436-443
Open AccessNumerical Modelling of Ultra-High Molecular Weight Polyethylene Composite under Impact Loading
- 1 January 2015
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 75, 110-122
A non-linear orthotropic hydrocode model for ultra-high molecular weight polyethylene in impact simulations
- 1 January 2015
- Published by Elsevier in International Journal of Impact Engineering
- Vol. 75, 110-122
A non-linear orthotropic hydrocode model for ultra-high molecular weight polyethylene in impact simulations
- 3 June 2014
- Published by WITPRESS LTD. in Computers in Railways XIV
- Vol. 1, 371-381
Numerical sensitivity studies of a UHMWPE composite for ballistic protection
Ultra-high molecular weight polyethylene (UHMWPE) has a high potential for ballistic armor applications due to the excellent weight specific...
- 3 June 2014
- Published by WITPRESS LTD. in Computers in Railways XIV
- Vol. 1, 371-381
Numerical sensitivity studies of a UHMWPE composite for ballistic protection
Ultra-high molecular weight polyethylene (UHMWPE) has a high potential for ballistic armor applications due to the excellent weight specific...