NINorihiko Iki

Norihiko Iki

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Norihiko Iki has a total of 43 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Achieving high flame stability with low NO And Zero N2O and NH3 emissions during liquid ammonia spray combustion with gas turbine combustors

    by Ekenechukwu C. Okafor, Osamu Kurata, Hirofumi Yamashita, Norihiko Iki, Takahiro Inoue, Hyun Jo, Masayasu Shimura, Taku Tsujimura, Akihiro Hayakawa, Hideaki Kobayashi


  • Effect of Ambient Electrons on Primary Discharge Energy in Laser-Induced Discharge

    by Y. Hoshi, H. Yoshida, N. Iki

    We examined the laser-induced discharge (LID) in medium-vacuum air. The time-averaged discharge energy Wd of a primary discharge prior to an arc discharge was affected by the number of initial electrons. The initial electrons were produced by the laser irradiation of electrodes. The number of electrons was proportional to the energy of the laser, Lp. Thus, it was adjusted by changing Lp. Although the experimental conditions were rather limited, i.e., air at 200-Pa pressure, we demonstrated a simple relationship, Wd ∝ Vs2× Lps, where Vs is the applied voltage and s is an exponent determined empirically. Note that the number of initial electrons is a function of Lp. Such a simple relationship for the behavior of LID that incorporates Wd is proposed for the first time in this paper.

  • Success of Ammonia-Fired, Regenerator-Heated, Diffusion Combustion Gas Turbine Power Generation and Prospect of Low NOx Combustion With High Combustion Efficiency

    by Osamu Kurata, Norihiko Iki, Takayuki Matsunuma, Takahiro Inoue, Taku Tsujimura, Hirohide Furutani, Akihiro Hayakawa, Hideaki Kobayashi

    To protect against global warming, a massive influx of renewable energy is expected. Although hydrogen is a renewable media, its storage and transportation in large quantity is difficult. Ammonia, however, is a hydrogen energy carrier and carbon-free fuel, and its storage and transportation technology is already established. Although ammonia combustion was studied in the 1960s in the USA, the development of an ammonia combustion gas turbine had been abandoned because combustion efficiency was unacceptably low. Since that time, in the combustion field, ammonia has been thought of as a fuel N additive in the study of NOx formation. Recent demand for hydrogen carrier revives the usage of ammonia combustion, but no one has attempted an actual design setup for ammonia combustion gas turbine power generation. The National Institute of Advanced Industrial Science and Technology (AIST) in Japan successfully performed ammonia-kerosene co-fired gas turbine power generation in 2014, and ammonia-fired gas turbine power generation in 2015. In the facilities, a regenerator-heated, diffusion-combustion micro-gas turbine is used, and its high combustor inlet temperature enables high thermal efficiency of ammonia combustion compared with that of methane combustion. Adoption of the regenerator increased combustor inlet temperature and enhanced flame stability in ammonia-air combustion. Although NOx emission from a gas turbine combustor is high, a Selective Catalytic Reduction (SCR) after gas turbine combustor reduces NOx emission to less than 10 ppm. This means that the ammonia combustion gas turbine design, abandoned in the 1960s for its unacceptably low combustion efficiency, has performed successfully with regenerator and SCR technology. However, the weakness of these facilities was that they required large-size SCR equipment in order to suppress a high concentration of NOx. Although NOx reduction in the combustion process is desirable, low NOx combustion technology is difficult because ammonia had been thought of as a source of fuel-NO. In the case of premixed ammonia-air flame, there exists a low emission window of NOx and NH3 in a certain equivalence ratio, but combustion intensity is very low because the laminar burning velocity of NH3-air is one-fifth that of CH4-air. This means that, when utilizing the window of premixed ammonia-air flame, scale-up of the combustion chamber or fuel additives for enhancement of flame stability is necessary. This study shows that the addition of H2 is effective for low NOx combustion with high combustion efficiency. In addition, H2 can be easily made from NH3 decomposition. The other option is diffusion combustion. Further research on low NOx combustion is needed.


  • Operation and Flame Observation of Micro Gas Turbine Firing Ammonia

    by Norihiko Iki, Osamu Kurata, Takayuki Matsunuma, Takahiro Inoue, Taku Tsujimura, Hirohide Furutani, Hideaki Kobayashi, Akihiro Hayakawa

    A demonstration test with the aim to show the potential of ammonia-fired power plant is planned using a micro gas turbine. 50kW class turbine system firing kerosene is selected as a base model. Over 40kW of power generation was achieved by firing ammonia gas only. Over 40kW of power generation was also achieved by firing mixture of ammonia and methane. However ammonia gas supply increases NOx in the exhaust gas dramatically. NOx concentration in the exhaust gas of gas turbine reached at over 600ppm. In the case of the gas turbine operation firing kerosene-ammonia with 31kW of power generation at 75,000rpm of rotating speed, the LHV (Lower Heating Value) ratio of ammonia to the total supplied fuel was changed from 0% to 100% in detail. NO emission increases rapidly to around 400ppm with ammonia at 7% of LHV ratio of ammonia. Then NO emission increases gradually to 600ppm with ammonia at 27% of LHV ratio of ammonia. NO emission has the peak around 60% of LHV ratio of ammonia. NO emission decreases below 500ppm at 100% of LHV ratio of ammonia. The gas turbine operation firing methane-ammonia with 31kW of power generation at 75,000rpm of rotating speed was also tried. NO emission increases rapidly to around 470ppm with ammonia at 7% of LHV ratio of ammonia. Then NO emission increases gradually to 600ppm with ammonia around 30% of LHV ratio of ammonia. NO emission has the peak at 65% of LHV ratio of ammonia. NO emission decreases below 500ppm at 100% of LHV ratio of ammonia. Since the ammonia flame in the prototype combustor seems to be inhomogeneous, ammonia combustion in the prototype combustor may have high NOx region and low NOx region. Therefore there is a possibility of low-NOx combustion. Flame observation was planned to know combustion state for improvement toward the low NOx combustor. Flame observation from the combustor exit was available by extending the combustor exit with the adaptor of the bent coaxial tubes and the quartz window. Swirling flames of ammonia, methane and methane-ammonia were observed near the center axis of the combustor. Flame observation at 39.1kW of power generation was succeeded. In the case of the flame observation, fuel consumption increased due to increase of the heat loss from the combustor. The emissions of NO and NH3 clearly depend on the combustion inlet temperature at 75,000rpm of rotating speed. The emissions of NO and NH3 in the case of the flame observation setting corresponds to the emission in the case of the normal setting at the condition that the power output is 11.2kW lower.


  • Top Cited Papers

    Performances and emission characteristics of NH3–air and NH3CH4–air combustion gas-turbine power generations

    by Osamu Kurata, Norihiko Iki, Takayuki Matsunuma, Takahiro Inoue, Taku Tsujimura, Hirohide Furutani, Hideaki Kobayashi, Akihiro Hayakawa


  • Micro gas turbine cogeneration system with latent heat storage at the University: Part III: Temperature control schedule

    by Osamu Kurata, Norihiko Iki, Takayuki Matsunuma, Tetsuhiko Maeda, Satoshi Hirano, Katsuhiko Kadoguchi, Hiromi Takeuchi, Hiro Yoshida


  • Flow visualization of a non-contact transport device by Coanda effect

    by Norihiko Iki, Hiroyuki Abe, Takashi Okada

    AIST proposes new technology of non-contact transport device utilizing Coanda effect. A proposed non-contact transport device has a cylindrical body and circular slit for air. The air flow around non-contact device is turbulent and its flow pattern depends on the injection condition. Therefore we tried visualization of the air flow around non -contact device as the first step of PIV measurement. Several tracer particles were tried such as TiO2 particles, water droplets, potatoes starch, rice starch, corn starch. Hot-wire anemometer is employed to velocity measurement. TiO2 particles deposit inside of a slit and clogging of a slit occurs frequently. Potato starch particles do not clog a slit but they are too heavy to trace slow flow area. Water droplets by ultrasonic atomization also deposit inside of slit but they are useful to visualize flow pattern around a non-contact transport device by being supplied from circumference. Coanda effect of proposed non-contact transport device was confirmed and injected air flow pattern switches by a work. Air flow around non-contact trance port device is turbulent and its velocity range is wide. Therefore flow measurement by tracer part icle has traceability issue. Suitable tracer and exposure condition depends on target area.

  • Performance of IGFC With Exergy Recuperation

    by Norihiko Iki, Osamu Kurata, Atsushi Tsutsumi

    The Integrated coal Gasification Combined Cycle (IGCC) is considered to be a very clean and efficient system for coal-fired power generation. And given the development of 100 MW-scale solid oxide fuels cells (SOFCs), the integrated coal Gasification Fuel Cell combined cycle (IGFC) would be the most efficient coal-fired power generation system. However, more energy efficient power generation systems must be developed in order to reduce CO2 emissions over the middle and long term. Thus, the authors have proposed the Advanced Integrated coal Gasification Combined Cycle (A-IGCC) and Advanced IGFC (A-IGFC) systems, which utilize exhaust heat from solid oxide fuel cells (SOFCs) and/or gas turbines as a heat source for gasification (exergy recuperation). The A-IGCC and A-IGFC systems utilize a twin circulating fluidized bed coal gasifier consisting of three primary components: a pyrolyzer, steam reformer and partial combustor. The temperature of the steam reformer is 800 °C, and that of the partial oxidizer is 950 °C. Since the syngas, produced by pyrolysis and the reforming process involving volatile hydrocarbons, tar and char, contains carbon monoxide and hydrogen, the A-IGCC technology has considerable potential for higher thermal efficiency while utilizing low-grade coals. The coal types utilized in the study were bituminous Taiheiyo, sub-bituminous Adaro and Loy Yang coal. Milewski’s formula was used to model the circuit voltage of the SOFC. Cool gas efficiency increases, in order, from Taiheiyo coal to Adaro coal to Loy Yang coal. The A-IGFC system has the potential to achieve high thermal efficiency using various coals, with Loy Yang coal achieving the highest thermal efficiency. However, the drying process for Loy Yang and Adaro coal is an important issue.

  • Micro gas turbine cogeneration system with latent heat storage at the University: Part II: Part load and thermal priority mode

    by Osamu Kurata, Norihiko Iki, Takayuki Matsunuma, Tetsuhiko Maeda, Satoshi Hirano, Katsuhiko Kadoguchi, Hiromi Takeuchi, Hiro Yoshida