Hermann F. Fasel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hermann F. Fasel has a total of 159 co-authors. Here are the top co-authors by number of shared publications:
Andreas Gross
New Mexico State University
44 shared publicationsA. Gross
New Mexico State University, Las Cruces, New Mexico 88003
23 shared publications- Jayahar Sivasubramanian
University of Arizona, Tucson
20 shared publications - Shirzad Hosseinverdi
The University of Arizona
16 shared publications - Richard D. Sandberg
Department of Mechanical Engineering, University of Melbourne, Parkville, VIC 3010, Australia
14 shared publications Christoph Brehm
12 shared publications
Latest Publications
- 1 April 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 63 (4) , 1228-1242
Scaling and Transition Effects on Hollow-Cylinder/Flare Shock/Boundary-Layer Interactions in Wind Tunnel Environments
A comprehensive investigation into the flow over a hollow-cylinder and [ ] flare has been conducted at Mach 5 with transitional Reynolds numbers. Experiments of two similar models have been conducted in LT5 at the University of Arizona and R2Ch at ONERA. Considerable differences in reattachment behavior were observed from infrared thermography measurements indicating that the reattachment in LT5 was approximately twice as far from the flare base as observed in R2Ch. Supporting simulations have been performed at the University of Arizona and the Technical University of Munich. Various effects are reviewed: Mach numbers and wall temperatures modulating boundary-layer development, 3D relief effects due to differences in normalized cylinder diameters, leading-edge bluntness effects, and the impact of freestream disturbances. Simulations show that modulation of freestream noise amplitude can scale the interaction size to match experiments. Experimental investigation of the respective noise environment between the two facilities showed that despite exhibiting similar noise magnitudes, they differed considerably in frequency content, suggesting that additional parameters are required when quantifying wind tunnel freestream noise conditions. These discrepancies are believed to lead to greater seeding of shear layer instabilities in R2Ch, resulting in faster transition, consistent with the experimentally observed smaller recirculation bubble.
- 1 April 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 63 (4) , 1228-1242
Scaling and Transition Effects on Hollow-Cylinder/Flare Shock/Boundary-Layer Interactions in Wind Tunnel Environments
A comprehensive investigation into the flow over a hollow-cylinder and [ ] flare has been conducted at Mach 5 with transitional Reynolds numbers. Experiments of two similar models have been conducted in LT5 at the University of Arizona and R2Ch at ONERA. Considerable differences in reattachment behavior were observed from infrared thermography measurements indicating that the reattachment in LT5 was approximately twice as far from the flare base as observed in R2Ch. Supporting simulations have been performed at the University of Arizona and the Technical University of Munich. Various effects are reviewed: Mach numbers and wall temperatures modulating boundary-layer development, 3D relief effects due to differences in normalized cylinder diameters, leading-edge bluntness effects, and the impact of freestream disturbances. Simulations show that modulation of freestream noise amplitude can scale the interaction size to match experiments. Experimental investigation of the respective noise environment between the two facilities showed that despite exhibiting similar noise magnitudes, they differed considerably in frequency content, suggesting that additional parameters are required when quantifying wind tunnel freestream noise conditions. These discrepancies are believed to lead to greater seeding of shear layer instabilities in R2Ch, resulting in faster transition, consistent with the experimentally observed smaller recirculation bubble.
- 1 January 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 62 (1) , 162-174
Effects of Small Leading-Edge Bluntness on High-Speed Boundary-Layer Instabilities on Flat Plates
- 1 January 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 62 (1) , 162-174
Effects of Small Leading-Edge Bluntness on High-Speed Boundary-Layer Instabilities on Flat Plates
- 1 November 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 61 (11) , 4797-4807
Numerical Investigations of Nonlinearly Generated Disturbance Waves in High-Speed Boundary Layers
In several experimental investigations of hypersonic boundary-layer transition, higher harmonics of the linearly unstable second mode waves as well as low-frequency waves, which are not related to first mode waves, have been observed. It has been conjectured that the higher harmonics are nonlinearly generated by a self-interaction mechanism of the linearly amplified second mode waves. Several hypotheses regarding the origin of the low-frequency waves and their role in the transition process have been put forth. However, a clear understanding of the origin and role of these low-frequency disturbances in the transition process is difficult to attain from experiments and thus still not completely achieved. The nonlinear generation of higher harmonics and low-frequency disturbances is relevant because in high-speed boundary layers, second modes can reach very large amplitudes, which can lead to a considerable stretching of the transitional regime where these nonlinearly generated waves can then reach significant amplitudes and participate in the transition process. To shed light on this unresolved issue, numerical investigations were carried out for a flared cone at Mach 6. These calculations have shown that nonlinear interactions of sufficiently large-amplitude second mode waves can generate low-frequency disturbances. This was confirmed by a theoretical nonlinear interaction model.
- 1 November 2023
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 61 (11) , 4797-4807
Numerical Investigations of Nonlinearly Generated Disturbance Waves in High-Speed Boundary Layers
In several experimental investigations of hypersonic boundary-layer transition, higher harmonics of the linearly unstable second mode waves as well as low-frequency waves, which are not related to first mode waves, have been observed. It has been conjectured that the higher harmonics are nonlinearly generated by a self-interaction mechanism of the linearly amplified second mode waves. Several hypotheses regarding the origin of the low-frequency waves and their role in the transition process have been put forth. However, a clear understanding of the origin and role of these low-frequency disturbances in the transition process is difficult to attain from experiments and thus still not completely achieved. The nonlinear generation of higher harmonics and low-frequency disturbances is relevant because in high-speed boundary layers, second modes can reach very large amplitudes, which can lead to a considerable stretching of the transitional regime where these nonlinearly generated waves can then reach significant amplitudes and participate in the transition process. To shed light on this unresolved issue, numerical investigations were carried out for a flared cone at Mach 6. These calculations have shown that nonlinear interactions of sufficiently large-amplitude second mode waves can generate low-frequency disturbances. This was confirmed by a theoretical nonlinear interaction model.
- 20 June 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Laminar-Turbulent Transition in a Swept Low-Speed Boundary Layer
View Video Presentation: https://doi.org/10.2514/6.2022-3633.vid Evolution of three-dimensional disturbances in an accelerating swept laminar boundary layer is investigated by direct numerical simulations and linear parabolized stability equations (PSE). First, so-called controlled transition simulations were carried out where a single un- steady secondary instability wave is added to the baseflow distorted by a stationary primary crossflow vortex, and the nature of secondary instability regimes was identified. Next, the development of a three-dimensional wave packet was investigated, where the wave packet is generated by a localized short-duration pulse disturbance. DNS data support the results obtained from a PSE analysis, namely that the underlying baseflow is unstable with respect to both stationary and traveling crossflow modes with a wide range of frequencies and spanwise wavenumbers, whereby traveling crossflow modes are reaching the largest maximum amplitudes. Nonlinear mechanisms eventually trigger the transition process, as the wave packet breakdown to turbulent patches.
- 20 June 2022
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Laminar-Turbulent Transition in a Swept Low-Speed Boundary Layer
View Video Presentation: https://doi.org/10.2514/6.2022-3633.vid Evolution of three-dimensional disturbances in an accelerating swept laminar boundary layer is investigated by direct numerical simulations and linear parabolized stability equations (PSE). First, so-called controlled transition simulations were carried out where a single un- steady secondary instability wave is added to the baseflow distorted by a stationary primary crossflow vortex, and the nature of secondary instability regimes was identified. Next, the development of a three-dimensional wave packet was investigated, where the wave packet is generated by a localized short-duration pulse disturbance. DNS data support the results obtained from a PSE analysis, namely that the underlying baseflow is unstable with respect to both stationary and traveling crossflow modes with a wide range of frequencies and spanwise wavenumbers, whereby traveling crossflow modes are reaching the largest maximum amplitudes. Nonlinear mechanisms eventually trigger the transition process, as the wave packet breakdown to turbulent patches.
- 8 June 2020
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Numerical Investigation of Nonlinear Entropy-Layer Instability Waves for Hypersonic Boundary-Layers
Direct Numerical Simulations (DNS) were carried out to investigate the laminar-turbulent transition for a blunt (right) cone (7◦ half-angle) at Mach 5.9 and zero angle of attack. First, (linear) stability calculations were carried out employing the same DNS Navier-Stokes solver and using very small disturbance amplitudes in order to capture the linear disturbance devel- opment. Contrary to standard Linear Stability Theory results, these investigations revealed a strong “linear” instability in the entropy layer region for a very short downstream distance for oblique disturbance waves with spatial growth rates far exceeding those of second mode disturbances. This linear instability behavior was not captured with conventional LST and/or the Parabolized Stability Equations (PSE) approach. Secondly, a highly-resolved nonlinear breakdown simulation was performed using high-fidelity DNS. The DNS results showed that linearly unstable oblique disturbance waves, when excited with large enough amplitudes, lead to a rapid breakdown and complete laminar-turbulent transition in the entropy layer just downstream of the blunted nose.
- 8 June 2020
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Numerical Investigation of Nonlinear Entropy-Layer Instability Waves for Hypersonic Boundary-Layers
Direct Numerical Simulations (DNS) were carried out to investigate the laminar-turbulent transition for a blunt (right) cone (7◦ half-angle) at Mach 5.9 and zero angle of attack. First, (linear) stability calculations were carried out employing the same DNS Navier-Stokes solver and using very small disturbance amplitudes in order to capture the linear disturbance devel- opment. Contrary to standard Linear Stability Theory results, these investigations revealed a strong “linear” instability in the entropy layer region for a very short downstream distance for oblique disturbance waves with spatial growth rates far exceeding those of second mode disturbances. This linear instability behavior was not captured with conventional LST and/or the Parabolized Stability Equations (PSE) approach. Secondly, a highly-resolved nonlinear breakdown simulation was performed using high-fidelity DNS. The DNS results showed that linearly unstable oblique disturbance waves, when excited with large enough amplitudes, lead to a rapid breakdown and complete laminar-turbulent transition in the entropy layer just downstream of the blunted nose.
- 8 June 2020
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Investigation of low-speed boundary-layer instability and transition using experiments, theory and DNS
A collaborative study of boundary layer instability and transition has been conducted using wind tunnel experiments, direct numerical simulations (DNS) and linear stability theory (LST). Experiments are performed in the Arizona Low Speed Wind Tunnel (ALSWT) at approximately 7m/s (unit Reynolds number of 4.2 x 10^5 m^-1). The ALSWT test section velocity is adjustable through variation of the fan RPM and blade angle. A parametric study yielded minimum turbulence intensities of approximately 0.022% (1 Hz-10 kHz) over a range of RPM and blade angles. This low turbulence intensity was accompanied by benign spectral content primarily associated with blade passage frequency which could be moved outside of the range of interest for boundary layer stability studies. Installation of a flat plate and corresponding support structure increased turbulence intensity to 0.028% (1 Hz-10 kHz) but had no negative influence on stability experiments. Precursor calculations of the test section flow field were performed with ANSYS Fluent to provide boundary conditions for subsequent high resolution DNS in the region of interest on the flat plate downstream of the leading edge. A detailed comparison between experiments and DNS shows good agreement between boundary layer velocity profiles. Subtle discrepancies between experiments and DNS are attributed to the existence of favorable pressure gradient (beta_H = 0.015) in the experiment which results in slightly fuller velocity profiles and a more stable boundary layer. Disturbance growth experiments (linear problem) are performed using alternating current dielectric barrier discharge (ac- DBD) plasma actuators. A linearized Navier-Stokes solver was employed to map out the linear stability diagram which then guided the actuator location (Re_x = 10^5) and forcing frequency (50 Hz) to allow observation of both growth and decay of the disturbance amplitudes over the extent of the domain. Disturbance growth measurements are in good agreement between experiments and DNS for both first and second maxima and any discrepancies are explained by consideration of pressure gradient and nonzero free-stream turbulence in the experiment which is not captured in DNS. Finally, branch one and branch two neutral curves for a range of ac-DBD plasma forcing frequencies (30 Hz-100 Hz) are identified from experimental data and compare well with LST. Overall, these results show the utility of the ALSWT as a test bed for boundary layer stability and transition research.
- 8 June 2020
- Published by American Institute of Aeronautics and Astronautics (AIAA)
Investigation of low-speed boundary-layer instability and transition using experiments, theory and DNS
A collaborative study of boundary layer instability and transition has been conducted using wind tunnel experiments, direct numerical simulations (DNS) and linear stability theory (LST). Experiments are performed in the Arizona Low Speed Wind Tunnel (ALSWT) at approximately 7m/s (unit Reynolds number of 4.2 x 10^5 m^-1). The ALSWT test section velocity is adjustable through variation of the fan RPM and blade angle. A parametric study yielded minimum turbulence intensities of approximately 0.022% (1 Hz-10 kHz) over a range of RPM and blade angles. This low turbulence intensity was accompanied by benign spectral content primarily associated with blade passage frequency which could be moved outside of the range of interest for boundary layer stability studies. Installation of a flat plate and corresponding support structure increased turbulence intensity to 0.028% (1 Hz-10 kHz) but had no negative influence on stability experiments. Precursor calculations of the test section flow field were performed with ANSYS Fluent to provide boundary conditions for subsequent high resolution DNS in the region of interest on the flat plate downstream of the leading edge. A detailed comparison between experiments and DNS shows good agreement between boundary layer velocity profiles. Subtle discrepancies between experiments and DNS are attributed to the existence of favorable pressure gradient (beta_H = 0.015) in the experiment which results in slightly fuller velocity profiles and a more stable boundary layer. Disturbance growth experiments (linear problem) are performed using alternating current dielectric barrier discharge (ac- DBD) plasma actuators. A linearized Navier-Stokes solver was employed to map out the linear stability diagram which then guided the actuator location (Re_x = 10^5) and forcing frequency (50 Hz) to allow observation of both growth and decay of the disturbance amplitudes over the extent of the domain. Disturbance growth measurements are in good agreement between experiments and DNS for both first and second maxima and any discrepancies are explained by consideration of pressure gradient and nonzero free-stream turbulence in the experiment which is not captured in DNS. Finally, branch one and branch two neutral curves for a range of ac-DBD plasma forcing frequencies (30 Hz-100 Hz) are identified from experimental data and compare well with LST. Overall, these results show the utility of the ALSWT as a test bed for boundary layer stability and transition research.
- 1 March 2019
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 56 (2) , 333-346
History and Progress of Boundary-Layer Transition on a Mach-6 Flared Cone
- 1 March 2019
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Spacecraft and Rockets
- Vol. 56 (2) , 333-346
History and Progress of Boundary-Layer Transition on a Mach-6 Flared Cone
- 1 March 2019
- Published by Elsevier in Journal of Computational Physics
- Vol. 380, 243-268
An efficient linear wavepacket tracking method for hypersonic boundary-layer stability prediction
- 1 March 2019
- Published by Elsevier in Journal of Computational Physics
- Vol. 380, 243-268
An efficient linear wavepacket tracking method for hypersonic boundary-layer stability prediction
- 1 December 2018
- Published by Elsevier in Journal of Computational Physics
- Vol. 374, 912-940
An efficient, high-order method for solving Poisson equation for immersed boundaries: Combination of compact difference and multiscale multigrid methods
- 1 December 2018
- Published by Elsevier in Journal of Computational Physics
- Vol. 374, 912-940
An efficient, high-order method for solving Poisson equation for immersed boundaries: Combination of compact difference and multiscale multigrid methods