Luis Henrique DA Silva Teixeira
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Luis Henrique DA Silva Teixeira has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Auteliano Antunes Santos
DSI/FEM, Universidade Estadual de Campinas (UNICAMP), Rua Mendeleyev, 200, Campinas, São Paulo, Brazil
2 shared publications - Paulo Roberto Gardel Kurka
School of Mechanical Engineering, University of Campinas, Campinas, Brazil
2 shared publications - Guilherme Fabiano Mendonça dos Santos
Universidade Federal do Espírito Santo - Departamento de Engenharia Mecânica
1 shared publication - J. Izuka
University of Campinas, 13083-970, São Paulo, Brazil
1 shared publication Jaime Hideo Izuka
Faculdade de Ciências Aplicadas / UNICAMP ( Universidade Estadual de Campinas )
1 shared publication- Jony Javorski Eckert
Department of Integrated Systems, School of Mechanical Engineering - FEM, University of Campinas - UNICAMP, Campinas, Brazil
1 shared publication
Latest Publications
- 29 August 2022
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 61 (9) , 2456-2471
Dynamic simulation of a heavy-haul freight car under abnormal braking application on tangent and curve
Couples of heavy-haul freight cars are simulated, using a 62-degree-of-freedom multi-body model developed on Simpack®, running on both tangent track and circular curve under different conditions. A benchmark simulation running at a speed of 70 km/h is set up, and then, different breaking scenarios with 2.5 kN, 5 kN, 7.5 kN and 10 kN of abnormal braking force application are simulated. In this paper, the effect of forces acting on the wheel–rail interface is compared using the derailment coefficient (L/V) and the material wear, defined by energy dissipation (Tγ). For the double-wagon setup placed in various positions along the train, the simulations run under no braking and abnormal braking conditions, where the braking force acts in only one of the wheels of the wheelset. This condition leads to an increase of up to 18% in L/V in one curve and up to 17% of reduction on the curve in the other direction. The wear increases 68% and decreases 71%, depending on the direction of the curve. These effects haven't been associated with longitudinal dynamic effects in previous studies, including in-car shocks and traction forces.
- 29 August 2022
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 61 (9) , 2456-2471
Dynamic simulation of a heavy-haul freight car under abnormal braking application on tangent and curve
Couples of heavy-haul freight cars are simulated, using a 62-degree-of-freedom multi-body model developed on Simpack®, running on both tangent track and circular curve under different conditions. A benchmark simulation running at a speed of 70 km/h is set up, and then, different breaking scenarios with 2.5 kN, 5 kN, 7.5 kN and 10 kN of abnormal braking force application are simulated. In this paper, the effect of forces acting on the wheel–rail interface is compared using the derailment coefficient (L/V) and the material wear, defined by energy dissipation (Tγ). For the double-wagon setup placed in various positions along the train, the simulations run under no braking and abnormal braking conditions, where the braking force acts in only one of the wheels of the wheelset. This condition leads to an increase of up to 18% in L/V in one curve and up to 17% of reduction on the curve in the other direction. The wear increases 68% and decreases 71%, depending on the direction of the curve. These effects haven't been associated with longitudinal dynamic effects in previous studies, including in-car shocks and traction forces.
- 1 February 2021
- Published by Taylor & Francis in Mechanics Based Design of Structures and Machines
- Vol. 51 (3) , 1606-1625
A fast simulation approach to assess draft gear loads for heavy haul trains during braking
Train traction and brake dynamics simulations can be used to improve the safety and efficiency of heavy haul transportation. Virtual models can be used to analyze many operational conditions that are expensive or inviable to be measured due to costs and security risks. This paper presents a low computational cost simulation model that encompasses the longitudinal dynamics equations and the pneumatic brake system behavior. The model is used to evaluate the effects of the locomotive traction/dynamic-brake and of the pneumatic brake delays in the draft gear forces. A real-world scenario was analyzed, in which a standard train control procedure was applied for 168 ore freight cars propelled by two locomotives. For this analysis, the model was able to perform up to 8 simultaneous parallel simulations with a processing time of 607 s to conclude a route of 2884 s, which is very suitable for this kind of investigation.
- 1 February 2021
- Published by Taylor & Francis in Mechanics Based Design of Structures and Machines
- Vol. 51 (3) , 1606-1625
A fast simulation approach to assess draft gear loads for heavy haul trains during braking
Train traction and brake dynamics simulations can be used to improve the safety and efficiency of heavy haul transportation. Virtual models can be used to analyze many operational conditions that are expensive or inviable to be measured due to costs and security risks. This paper presents a low computational cost simulation model that encompasses the longitudinal dynamics equations and the pneumatic brake system behavior. The model is used to evaluate the effects of the locomotive traction/dynamic-brake and of the pneumatic brake delays in the draft gear forces. A real-world scenario was analyzed, in which a standard train control procedure was applied for 168 ore freight cars propelled by two locomotives. For this analysis, the model was able to perform up to 8 simultaneous parallel simulations with a processing time of 607 s to conclude a route of 2884 s, which is very suitable for this kind of investigation.
- 22 October 2016
- Published by PIBIC Unicamp
- p. 51493
Adjust of the dynamic model of a beam with large deformation by experimental modal analysis
The use of long and flexible probes in space exploration is convenient so that you can explore places of scientific interest that are hard to reach. However, these types of systems presents difficulties regarding the vibration control. This paper proposes a simplified numerical model of a long... Anais PIBIC 2016 | Trabalhos apresentados durante o XXIV Congresso de Iniciação Científica da Unicamp, parte do projeto PIBIC.
- 22 October 2016
- Published by PIBIC Unicamp
- p. 51493
Adjust of the dynamic model of a beam with large deformation by experimental modal analysis
The use of long and flexible probes in space exploration is convenient so that you can explore places of scientific interest that are hard to reach. However, these types of systems presents difficulties regarding the vibration control. This paper proposes a simplified numerical model of a long... Anais PIBIC 2016 | Trabalhos apresentados durante o XXIV Congresso de Iniciação Científica da Unicamp, parte do projeto PIBIC.
- 1 October 2016
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 79, 271-288
Large deflections and vibrations of a tip pulled beam with variable transversal section
- 1 October 2016
- Published by Elsevier in Mechanical Systems and Signal Processing
- Vol. 79, 271-288
Large deflections and vibrations of a tip pulled beam with variable transversal section