RGRolando Guzman

Rolando Guzman

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Rolando Guzman has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Bio‐Stabilised Earth and the Sustainability of the Built Environment: Experimental Evidence of Passive Environmental Moderation

    by Anya Montserrat Pulido Cavada, Mar Hernández Martín, Rolando Enrique Guzmán‐López, Federico de Isidro Gordejuela, Roberto Alonso González‐Lezcano

    In a context of increasing pressure on natural resources and the need for lower‐impact, circular construction materials, bio‐stabilised earth is receiving renewed attention. This study evaluates the environmental response of a full‐scale prototype built with locally sourced earth, tannin and fique fibres, monitored for 41 days in Madrid under a permanently naturally ventilated, non‐hermetic semi‐outdoor configuration. Rather than demonstrating the known thermal‐mass or hygroscopic behaviour of earth, the study assesses whether measurable hygrothermal moderation remains observable at construction scale under strong indoor‐outdoor coupling. Temperature and relative humidity were the primary performance variables, while particulate matter and CO 2 were complementary observations. Across 37 valid paired days with at least 95% temporal coverage, the mean daily P5‐P95 air‐temperature range was 7.70°C outdoors and 3.83°C indoors, yielding a mean normalised indoor/outdoor amplitude ratio of 0.510 (95% bootstrap CI: 0.486–0.539), equivalent to 49.0% lower robust daily variability indoors. For relative humidity, the corresponding ranges were 28.73 and 17.03 percentage points, with a mean ratio of 0.593 (95% CI: 0.537–0.651), equivalent to 40.7% lower variability. Paired Wilcoxon tests were significant for both variables ( p < 0.001). PM concentrations were only slightly lower indoors and are not interpreted as evidence of filtration. Aranet4 CO 2 series showed strong concurrent indoor‐outdoor variation ( r = 0.936), supporting strong air coupling rather than pollutant attenuation. These results provide case‐specific system‐level evidence of hygrothermal moderation without attributing the response uniquely to bio‐stabilising additives or extrapolating it to comfort, energy savings, long‐term durability, life‐cycle advantage or quantified SDG performance.

  • Open Access

    Fique as a Sustainable Material and Thermal Insulation for Buildings: Study of Its Decomposition and Thermal Conductivity

    by Gabriel Fernando García Sánchez, Rolando Enrique Guzmán López, Roberto Alonso Gonzalez-Lezcano

    Buildings consume a large amount of energy during all stages of their life cycle. One of the most efficient ways to reduce their consumption is to use thermal insulation materials; however, these generally have negative effects on the environment and human health. Bio-insulations are presented as a good alternative solution to this problem, thus motivating the study of the properties of natural or recycled materials that could reduce energy consumption in buildings. Fique is a very important crop in Colombia. In order to contribute to our knowledge of the properties of its fibers as a thermal insulator, the measurement of its thermal conductivity is reported herein, employing equipment designed according to the ASTM C 177 standard and a kinetic study of its thermal decomposition from thermogravimetric data through the Coats–Redfern model-fitting method.


  • Open Access

    Fique as thermal insulation morphologic and thermal characterization of fique fibers

    by Gabriel Fernando García Sánchez, R E Guzmán, Adriana Restrepo‐Osorio, Emil Hernández Arroyo

    Bio-insulations have gained great interest in recent years due to their potential to reduce energy consumption without negative environmental impacts. Fique is one of the most important crops in Colombia, it has shown a low thermal conductivity which makes it a potential replacement for the common insulation materials. However, there are few works that study its thermal properties. In order to enhance the understanding of fique as thermal insulation, in this paper a morphological analysis of raw fique fibers and Thermogravimetry (TGA) and Differential Scanning Calorimetry (DSC) tests of three fique samples are presented, namely, natural fique without treatment, fique washed with a commercial softener and fique after having been soaked for 24 hours in the same softener.


  • Mixed-Mode Stress Intensity Factors for Tubes under Pure Torsion Loading

    by Jorge G. Diaz, Luiz Fernando Nazaré Marques, Rolando Enrique Guzmán

    Although it seems like a common load-geometry configuration, there is neither an analytical nor a numerical solution for Stress Intensity Factors (SIF) in cracked tubes under pure torsion. Standards such as API 579, BS 7910 or handbooks do not present such case. There is plenty of solutions based on FEM or weight functions calculations for an extensive load-geometry combinations, but not for tubes under pure torsion. This paper shows curves of KI, KII, and KIII for through-wall cracks obtained with ANSYS simulations for slim tubes, under pure torsion with a rounded horizontal slit, numerically calculated via J-integral. Additionally KI, KII, and KIII are calculated using relative displacement between two points along the crack lips using Linear Elastic Fracture Mechanics (LEFM) formulations for Crack Tip Opening Displacement (COD) and Crack Tip Sliding Displacement (CTSD). Results are compared with experimentally measured SIF using the Digital Image Correlation (DIC) technique for fatigued-growth cracks reported in literature.


  • Open Access

    Análisis modal de material compuesto de resina bioepoxy/fibra de fique

    by Sergio Gómez, Bladimir Ramón, Rolando Guzmán

    In this work, a modal analysis was applied on a bioepoxy/ fi ber composite material using the simulation (Finite Elements), experimentation and analytical modeling knowing the deviation between each of the methods of the solution. The material was elaborated using a bioepoxy resin and fi que fi bers in the distribution of weave under the technique of manufacturing the infusion vacuum. Tensile tests were performed on the composite material according to ASTM D3039 / D3039M to obtain the mechanical properties that allow the development of the mathematical model and the simulation and analysis of scanning electron microscopy to observe the adhesion between the fi ber and the matrix. The experimental modal analysis was performed by measuring the frequency response (FRF) under ISO 7626-2. The Euler-Bernoulli equation was used for analytical modeling, while the ANSYS fi nite element software was used for the simulation. It concludes that for the fi rst modes of material vibration obtained results close between the three methods, however for the third mode the error increases by the interaction between the matrix and the fi ber and the eff ects of the rotation of the cross-section of the test item.


  • Open Access

    Comparative study of the mechanical and vibratory properties of a composite reinforced with fique fibers versus a composite with E-glass fibers

    by Universidad Pontificia Bolivariana, Sergio Gómez, Bladimir Ramón, Universidad de Pamplona, Rolando Guzman


  • Open Access

    Comparison of the Time Domain Windows Specified in the ISO 18431 Standards Used to Estimate Modal Parameters in Steel Plates

    by Jhonatan Camacho-Navarro, R. Guzmán-López, Sergio Gómez, Marco Flórez

    The procedures used to estimate structural modal parameters as natural frequency, damping ratios, and mode shapes are generally based on frequency methods. However, methods of time-frequency analysis are highly sensible to the parameters used to calculate the discrete Fourier transform: windowing, resolution, and preprocessing. Thus, the uncertainty of the modal parameters is increased if a proper parameter selection is not considered. In this work, the influence of three different time domain windows functions (Hanning, flat-top, and rectangular) used to estimate modal parameters are discussed in the framework of ISO 18431 standard. Experimental results are conducted over an AISI 1020 steel plate, which is excited by means of a hammer element. Vibration response is acquired by using acceleration records according to the ISO 7626-5 reference guides. The results are compared with a theoretical method and it is obtained that the flat-top window is the best function for experimental modal analysis.

  • Open Access

    Comparison of three systems of solar water heating by thermosiphon

    by E Hernández, R E Guzmán

    The main purpose of this project was to elaborate a comparison between three water heating systems; using two plane water heating solar collector and another using a vacuum tube heater, all of them are on top of the cafeteria's roof on building of the "Universidad Pontificia Bolivariana" in Bucaramanga, Colombia. Through testing was determined each type of water heating systems' performance, where the Stainless Steel tube collector reached a maximum efficiency of 71.58%, the Copper Tubing Collector a maximum value of 76.31% and for the Vacuum Tube Heater Collector a maximum efficiency of 72.33%. The collector with copper coil was the system more efficient. So, taking into account the Performance and Temperature Curves, along with the weather conditions at the time of the testing we determined that the most efficient Solar Heating System is the one using a Vacuum Tube Heater Collector. Reaching a maximum efficiency of 72.33% and a maximum temperature of 62.6°C.