Yuandong Guo
Yuandong Guo has a total of 64 co-authors. Here are the top co-authors by number of shared publications:
- DongHyun Kim
EMC Laboratory, Missouri University of Science and Technology, Rolla, MO, USA
8 shared publications - Jun Fan
Department of Electrical Engineering, Missouri University of Science and Technology, Rolla, MO, USA
6 shared publications - Xiaoning Ye
Intel Corporation, Hillsboro, OR, USA
5 shared publications - Yuanzhuo Liu
Electromagnetic Compatibility Laboratory, Missouri University of Science and Technology, Rolla, MO, USA
4 shared publications - Chaofeng Li
Electromagnetic Compatibility Laboratory, Missouri University of Science and Technology, Rolla, MO, USA
3 shared publications - David Pommerenke
Graz University of Technology
3 shared publications
Latest Publications
- 10 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 4, 185-190
De-Embedding for Coupled Three-Port Devices
De-embedding techniques have been introduced to evaluate the real electrical performances of a device under test (DUT), e.g., the traditional thru-reflect-line (TRL) and short-open-load-thru (SOLT) standards, where the transfer matrix (T-matrix) and its inverse form are adopted in the mathematical process. A DUT may have three coupled ports in the fields of radiofrequency (RF) and electromagnetic compatibility (EMC). The symmetry in the corresponding S-matrix breaks down, because the numbers of incident and reflected ports are not equal. Thus, it leads to a non-square T-matrix by definition. Given that the inverse expression of a non-square matrix does not exist, the conventional de-embedding methods are inapplicable for a coupled three-port network. In this paper, a de-embedding algorithm which is feasible for coupled three-port devices is proposed and verified through the measurement. The proposed de-embedding technique may also be applied on devices with more than three ports.
- 10 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 4, 185-190
De-Embedding for Coupled Three-Port Devices
De-embedding techniques have been introduced to evaluate the real electrical performances of a device under test (DUT), e.g., the traditional thru-reflect-line (TRL) and short-open-load-thru (SOLT) standards, where the transfer matrix (T-matrix) and its inverse form are adopted in the mathematical process. A DUT may have three coupled ports in the fields of radiofrequency (RF) and electromagnetic compatibility (EMC). The symmetry in the corresponding S-matrix breaks down, because the numbers of incident and reflected ports are not equal. Thus, it leads to a non-square T-matrix by definition. Given that the inverse expression of a non-square matrix does not exist, the conventional de-embedding methods are inapplicable for a coupled three-port network. In this paper, a de-embedding algorithm which is feasible for coupled three-port devices is proposed and verified through the measurement. The proposed de-embedding technique may also be applied on devices with more than three ports.
- 26 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 4, 149-155
Extraction of DK glass and DK resin for PCB Striplines and Analysis of Far-End Crosstalk
Far-end crosstalk (FEXT) in typical high-speed printed circuit board (PCB) striplines is primarily attributed to dielectric inhomogeneity. In this paper, the inhomogeneity problem is comprehensively addressed by a novel algorithm that characterizes the dielectric constants (DKs) of glass fibers and epoxy resin. In contrast to other methods, the proposed approach enables one to assess the impact of geometrical parameters on stripline FEXT and to estimate DKcore and DKprepreg based on DKglass and DKresin values extracted through analytical expressions. Full-wave simulations and real-board measurements are conducted to verify the proposed approach.
- 26 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 4, 149-155
Extraction of DK glass and DK resin for PCB Striplines and Analysis of Far-End Crosstalk
Far-end crosstalk (FEXT) in typical high-speed printed circuit board (PCB) striplines is primarily attributed to dielectric inhomogeneity. In this paper, the inhomogeneity problem is comprehensively addressed by a novel algorithm that characterizes the dielectric constants (DKs) of glass fibers and epoxy resin. In contrast to other methods, the proposed approach enables one to assess the impact of geometrical parameters on stripline FEXT and to estimate DKcore and DKprepreg based on DKglass and DKresin values extracted through analytical expressions. Full-wave simulations and real-board measurements are conducted to verify the proposed approach.
- 20 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 4, 81-87
Accurate and Broadband Three-Phase Motor Modeling Methodology Based on Vector Fitting
An accurate and broadband modeling methodology for a typical permanent magnet synchronous motor (PMSM) in a vehicular three-phase braking system is proposed for the first time to improve the accuracy of induced electromagnetic interference (EMI) in three-phase motor systems. The proposed model is verified by measurement from DC to 120 MHz both in common-mode and differential-mode current measurement of the three-phase motor under study. and the proposed model can be used in analysis and prediction of the electromagnetic noise of the motor-drive braking system. The model can also be incorporated into frequency- and time-domain simulations. The modeling approach is based on vector fitting technique of measured three-phase motor impedance and S-parameter, where the three-phase PMSM is modeled as a multi-port device. In addition, the proposed modeling method for the PMSM can be used for different types of three-phase motors for EMI simulations and analysis.
- 20 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 4, 81-87
Accurate and Broadband Three-Phase Motor Modeling Methodology Based on Vector Fitting
An accurate and broadband modeling methodology for a typical permanent magnet synchronous motor (PMSM) in a vehicular three-phase braking system is proposed for the first time to improve the accuracy of induced electromagnetic interference (EMI) in three-phase motor systems. The proposed model is verified by measurement from DC to 120 MHz both in common-mode and differential-mode current measurement of the three-phase motor under study. and the proposed model can be used in analysis and prediction of the electromagnetic noise of the motor-drive braking system. The model can also be incorporated into frequency- and time-domain simulations. The modeling approach is based on vector fitting technique of measured three-phase motor impedance and S-parameter, where the three-phase PMSM is modeled as a multi-port device. In addition, the proposed modeling method for the PMSM can be used for different types of three-phase motors for EMI simulations and analysis.
- 23 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Analysis and Modeling Framework of Common Mode Noise in a Three-phase Motor System
Electromagnetic interference (EMI) issue is one of the major constraints of power electronic converters, especially for variable-speed systems. In this work, the common mode noise in a three-phase motor system is analyzed and modeled. The three-phase pulse-width modulation (PWM) inverter creates high magnitudes of dv/dt and di/dt, resulting in common mode noise and disturbance power. In this paper, the common mode noise and disturbance power modeling method are proposed for three-phase motor systems. The proposed equivalent circuit model comprises detailed models for insulated gate bipolar transistors (IGBTs), EMI filters, a three-phase motor and a printed circuit board (PCB). The proposed model of a three-phase system was verified by measurement with and without additional Y-capacitors. The measured and modeled common-mode noise shows a correlation in broadband common-mode noise reduction.
- 23 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Analysis and Modeling Framework of Common Mode Noise in a Three-phase Motor System
Electromagnetic interference (EMI) issue is one of the major constraints of power electronic converters, especially for variable-speed systems. In this work, the common mode noise in a three-phase motor system is analyzed and modeled. The three-phase pulse-width modulation (PWM) inverter creates high magnitudes of dv/dt and di/dt, resulting in common mode noise and disturbance power. In this paper, the common mode noise and disturbance power modeling method are proposed for three-phase motor systems. The proposed equivalent circuit model comprises detailed models for insulated gate bipolar transistors (IGBTs), EMI filters, a three-phase motor and a printed circuit board (PCB). The proposed model of a three-phase system was verified by measurement with and without additional Y-capacitors. The measured and modeled common-mode noise shows a correlation in broadband common-mode noise reduction.
- 16 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Letters on Electromagnetic Compatibility Practice and Applications
- Vol. 5 (3) , 92-96
Surface Roughness Effect From Different Surfaces of Microstrip Lines and Reference Plane
Microstrip line structures consist of different conductors, such as trace and reference planes, which have different surface roughness levels due to the printed circuit board manufacturing process. The bottom surface of the trace is often rougher than the top surface of the trace, and the roughness levels of different reference planes vary for different foil types and manufacturing processes. To accurately model the additional conductor loss caused by such differences in microstrip lines, a new modeling method is proposed with different roughness levels on different surfaces and a reference plane, in contrast to the traditional roughness modeling approach, which considers a uniform roughness distribution for all surfaces. The effect of the different surfaces on the resistance is determined by applying additional microstrip models to analyze the effect of surface roughness from different surfaces and to improve the accuracy of insertion loss prediction based on the modeled total resistance.
- 16 May 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Letters on Electromagnetic Compatibility Practice and Applications
- Vol. 5 (3) , 92-96
Surface Roughness Effect From Different Surfaces of Microstrip Lines and Reference Plane
Microstrip line structures consist of different conductors, such as trace and reference planes, which have different surface roughness levels due to the printed circuit board manufacturing process. The bottom surface of the trace is often rougher than the top surface of the trace, and the roughness levels of different reference planes vary for different foil types and manufacturing processes. To accurately model the additional conductor loss caused by such differences in microstrip lines, a new modeling method is proposed with different roughness levels on different surfaces and a reference plane, in contrast to the traditional roughness modeling approach, which considers a uniform roughness distribution for all surfaces. The effect of the different surfaces on the resistance is determined by applying additional microstrip models to analyze the effect of surface roughness from different surfaces and to improve the accuracy of insertion loss prediction based on the modeled total resistance.
- 16 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 1, 150-159
Phase Noise Analysis of Clock Generator by Using Phase Noise Sensitivity
Phase noise represents signal instabilities in the frequency domain and is assessed through power measurements at various offsets from the carrier frequency. Herein, the phase noise of a clock generator is analyzed and modeled. Sources for the phase noise of the clock output at the resonance frequency are identified, including the power supply, the heat sink, and the external crystal. Low-frequency resonance is detected and validated to be caused by the external crystal grounding design. Solutions to decrease crystal-related noise are proposed and validated. In addition, the sensitivity based on the signal-to-noise ratio is proposed and verified with measurements, to numerically analyze the effects of power supply noise on clock phase noise. The proposed phase noise sensitivity is extracted from the measured phase noise results and can be used to estimate the phase noise and jitter of different power supply noises. The extraction and prediction method are validated with different buffer types including LVDS, HCSL, LVPECL, and LVCMOS in a device under test with the given design.
- 16 November 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 1, 150-159
Phase Noise Analysis of Clock Generator by Using Phase Noise Sensitivity
Phase noise represents signal instabilities in the frequency domain and is assessed through power measurements at various offsets from the carrier frequency. Herein, the phase noise of a clock generator is analyzed and modeled. Sources for the phase noise of the clock output at the resonance frequency are identified, including the power supply, the heat sink, and the external crystal. Low-frequency resonance is detected and validated to be caused by the external crystal grounding design. Solutions to decrease crystal-related noise are proposed and validated. In addition, the sensitivity based on the signal-to-noise ratio is proposed and verified with measurements, to numerically analyze the effects of power supply noise on clock phase noise. The proposed phase noise sensitivity is extracted from the measured phase noise results and can be used to estimate the phase noise and jitter of different power supply noises. The extraction and prediction method are validated with different buffer types including LVDS, HCSL, LVPECL, and LVCMOS in a device under test with the given design.
- 12 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 1, 130-139
An Empirical Modeling of Far-End Crosstalk and Insertion Loss in Microstrip Lines
The difference in the dielectric permittivity of the different dielectric layers (including air) surrounding the microstrip is one of the major contributors to the far-end crosstalk (FEXT) in microstrip lines. The dielectric of the microstrip in printed circuit boards (PCBs) fabrication usually consists of two layers: the solder mask layer and the substrate layer. The characterization of the relative permittivity ( $\varepsilon_{r}$ ), dielectric dissipation factor (tanδ) for the dielectric layers of the microstrip are important parameters for board-level electronic system designs. In addition, the foil surface roughness cannot be ignored for the conductor loss modeling. In this work, an extraction method with high accuracy is proposed to characterize the dielectric material and foil surface roughness properties from the measured S-parameters with known cross-sectional geometry up to 20GHz. With the extracted properties, the FEXT and insertion loss of the microstrip can be estimated more accurately, providing design guidelines for PCB design and the material selection of the microstrip.
- 12 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 1, 130-139
An Empirical Modeling of Far-End Crosstalk and Insertion Loss in Microstrip Lines
The difference in the dielectric permittivity of the different dielectric layers (including air) surrounding the microstrip is one of the major contributors to the far-end crosstalk (FEXT) in microstrip lines. The dielectric of the microstrip in printed circuit boards (PCBs) fabrication usually consists of two layers: the solder mask layer and the substrate layer. The characterization of the relative permittivity ( $\varepsilon_{r}$ ), dielectric dissipation factor (tanδ) for the dielectric layers of the microstrip are important parameters for board-level electronic system designs. In addition, the foil surface roughness cannot be ignored for the conductor loss modeling. In this work, an extraction method with high accuracy is proposed to characterize the dielectric material and foil surface roughness properties from the measured S-parameters with known cross-sectional geometry up to 20GHz. With the extracted properties, the FEXT and insertion loss of the microstrip can be estimated more accurately, providing design guidelines for PCB design and the material selection of the microstrip.
- 31 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 1, 93-103
Far-End Crosstalk Modeling and Prediction for Stripline With Inhomogeneous Dielectric Layers (IDLs)
Far-end crosstalk (FEXT) is a critical factor that limits signal integrity performance in high-speed systems. The FEXT level is sensitive to the dielectric inhomogeneity of the stripline in fabricated printed circuit boards (PCBs). The dielectric of the stripline is manufactured with multiple inhomogeneous dielectric layers (IDLs) of various resin and glass fiber bundles. A marginal difference in the dielectric permittivity of the IDLs can lead to a significant change FEXT level. In this article, a practical FEXT modeling methodology for striplines is proposed by introducing the extraction method for ${{\boldsymbol{\varepsilon }}}_{\boldsymbol{r}}$ of IDLs. The new stripline model is constructed with three IDLs comprised of core, prepreg, and resin pocket, to improve the model accuracy. With the cross-sectional geometry and measured S-parameters of the coupled striplines, ${{\boldsymbol{\varepsilon }}}_{\boldsymbol{r}}$ of IDLs can be extracted. In addition, an analytical model to predict the FEXT polarity and magnitude of the stripline caused by the inhomogeneity is proposed targeted for prelayout application. The proposed models have been verified using measurement. The proposed models can provide useful analysis methodology and design guidelines to mitigate the FEXT level in high-speed systems, especially for high-volume PCB tests in the prelayout and postlayout stages.
- 31 August 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Signal and Power Integrity
- Vol. 1, 93-103
Far-End Crosstalk Modeling and Prediction for Stripline With Inhomogeneous Dielectric Layers (IDLs)
Far-end crosstalk (FEXT) is a critical factor that limits signal integrity performance in high-speed systems. The FEXT level is sensitive to the dielectric inhomogeneity of the stripline in fabricated printed circuit boards (PCBs). The dielectric of the stripline is manufactured with multiple inhomogeneous dielectric layers (IDLs) of various resin and glass fiber bundles. A marginal difference in the dielectric permittivity of the IDLs can lead to a significant change FEXT level. In this article, a practical FEXT modeling methodology for striplines is proposed by introducing the extraction method for ${{\boldsymbol{\varepsilon }}}_{\boldsymbol{r}}$ of IDLs. The new stripline model is constructed with three IDLs comprised of core, prepreg, and resin pocket, to improve the model accuracy. With the cross-sectional geometry and measured S-parameters of the coupled striplines, ${{\boldsymbol{\varepsilon }}}_{\boldsymbol{r}}$ of IDLs can be extracted. In addition, an analytical model to predict the FEXT polarity and magnitude of the stripline caused by the inhomogeneity is proposed targeted for prelayout application. The proposed models have been verified using measurement. The proposed models can provide useful analysis methodology and design guidelines to mitigate the FEXT level in high-speed systems, especially for high-volume PCB tests in the prelayout and postlayout stages.
- 27 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (4) , 4713-4722
Systematic Characterization of Dual Probes for Electromagnetic Near-Field Measurement
In this paper, systematic characterization of the dual probe, which is designed for the near field simultaneous measurement of both electric and magnetic field, is investigated rgb0,0,0with a microstrip line as the device under test (DUT). The characterization includes frequency response, transmission performance, symmetry, reflection, the intrusion of probe to the DUT, isolation of electric and magnetic field responses, field profile and spatial resolution, and differential electric field suppression. The dual probes with different design are adopted to demonstrate the systematic characterization.
- 27 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 21 (4) , 4713-4722
Systematic Characterization of Dual Probes for Electromagnetic Near-Field Measurement
In this paper, systematic characterization of the dual probe, which is designed for the near field simultaneous measurement of both electric and magnetic field, is investigated rgb0,0,0with a microstrip line as the device under test (DUT). The characterization includes frequency response, transmission performance, symmetry, reflection, the intrusion of probe to the DUT, isolation of electric and magnetic field responses, field profile and spatial resolution, and differential electric field suppression. The dual probes with different design are adopted to demonstrate the systematic characterization.
- 7 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 62 (4) , 1007-1016
Measurement Techniques to Identify Soft Failure Sensitivity to ESD
Electrostatic discharge (ESD)-induced soft failures are a critical issue for electronic systems as the failures are mostly found after the hardware design is completed. Any changes applied to the hardware may delay the project. Diagnostic tools capable of identifying soft failure-induced malfunctions in an early stage of product design help to reduce the risk of late stage ESD-induced project delays. In many cases, soft failures can be directly observed by the user interface, system crash, or other obvious indicators. However, in an early product design stage the operation system may be marginal and applications may not be available. To improve the ability to detect soft failure critical design choices, this paper presents several methods to identify ESD-induced changes which may not be observable via direct observation. These methods include the observation of ac or dc currents, monitoring dc voltages, capturing near fields and processing them via short-term fast fourier transform (FFT), wavelet transformation, down mixing to audible range, and monitoring for latch-up via thermal imaging. The paper introduces the basis of each method, shows examples, and compares them for their detection ability.
- 7 August 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 62 (4) , 1007-1016
Measurement Techniques to Identify Soft Failure Sensitivity to ESD
Electrostatic discharge (ESD)-induced soft failures are a critical issue for electronic systems as the failures are mostly found after the hardware design is completed. Any changes applied to the hardware may delay the project. Diagnostic tools capable of identifying soft failure-induced malfunctions in an early stage of product design help to reduce the risk of late stage ESD-induced project delays. In many cases, soft failures can be directly observed by the user interface, system crash, or other obvious indicators. However, in an early product design stage the operation system may be marginal and applications may not be available. To improve the ability to detect soft failure critical design choices, this paper presents several methods to identify ESD-induced changes which may not be observable via direct observation. These methods include the observation of ac or dc currents, monitoring dc voltages, capturing near fields and processing them via short-term fast fourier transform (FFT), wavelet transformation, down mixing to audible range, and monitoring for latch-up via thermal imaging. The paper introduces the basis of each method, shows examples, and compares them for their detection ability.