CZCheng Zhang

Cheng Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Cheng Zhang has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Influence of Debinding Process on the Properties of Photopolymerization 3D Printed Cordierite Ceramics

    by Junyi Zhu, Cheng Zhang, Zhongqiang Luo, Jiwei Cao, Zhiyuan Liu, Pei Wang, Changyong Liu, Zhangwei Chen


  • Fabrication process of smooth functionally graded materials through a real-time inline control of the component ratio

    by Weiwei Guo, Zhaoliang Jiang, Cheng Zhang, Li Zhao, Zongxiang Jiang, Xinde Li, Guopeng Chen


  • Mechanical properties and tribological behaviors of yttria-zirconia ceramics with additions of graphene oxide by hot-press sintering for dental implants

    by Cheng Zhang, Zhaoliang Jiang, Li Zhao

    Yttria-zirconia (3Y-ZrO 2 ) ceramics are widely used in orthopedic implants and carbon nanotubes (CNTs) attract the public attention due to their unique properties. To investigate the effect of graphene oxide (GO) concentrations on the mechanical properties and tribological behaviors of 3Y-ZrO 2 for dental implants, 3Y-ZrO 2/ GO composites were prepared by hot-press sintering. GO was uniformly distributed in 3Y-ZrO 2 and the composites showed good mechanical properties and tribological behaviors with suitable GO concentration. A moderate content in ZG3 and ZG2 (the ceramic with 0.15 wt.% and 0.1 wt.% GO) improved the flexural strength and fracture toughness up to 200% and 40.9%, respectively, compared to 3Y-ZrO 2 . Microstructural surfaces presented crack deflection, crack bridging, and GO put-out in the composites. In addition, a lower or higher proportion of GO destroyed overall structures of ZG1 (the ceramic with 0.05 wt.% GO) and ZG4 (the ceramic with 0.2 wt.% GO). These not only reduced the mechanical performances, but also resulted to an increase in surface roughness. Besides, Worn surfaces showed micro-ploughing and plastic deformation were dominant wear mechanisms in the ZG0 (the ceramic without GO), however, the addition of GO transformed the wear from a severe state to mild owing to self-lubricating property. Thus, friction coefficient, wear rate and surface roughness of ZG3 were reduced to the least among all the composites.


  • Experimental investigation for roll-to-plate embossing of ordered micro-pyramid array on the silver sheet

    by Shuai Chen, Chengpeng Zhang, Zhaoliang Jiang, Jilai Wang, Cheng Zhang

    : Silver (Ag) micro-nano structure array is widely adopted in surface-enhanced Raman scattering (SERS) substrate for biological detection applications. The high-precision and high-efficiency construction of an ordered Ag micro-nano structure array becomes a crucial problem to be solved. In this study, the roll-to-plate (R2P) process was adopted for high-resolution and high-throughput fabrication of an ordered micro-pyramid array on the silver sheet, which could have a larger surface area to adsorb more probe molecules and possess potential to further expand the arrangement of hotspots in SERS application. The effects of main process parameters were analyzed through both single-factor and Box–Behnken design (BBD) experiments, including roller gap, temperature and speed. Based on single-factor experiments, it was found that the effect of roller speed was relatively small while the roller gap and temperature could cause significant effects on forming results. According to BBD experiments, it was known that the roller gap was the most important process parameter. A better process window for R2P embossing of the micro-pyramid array could be obtained, that was the temperature between 85 °C and 100 °C, the speed between 200 and 300 r min −1 , and the gap between 0.10 and 0.12 mm. This research could provide beneficial guidance for high-precision and high-efficiency fabrication of ordered micro-nano structure arrays.


  • Open Access

    Theoretical modeling and experimental characterization of boundary slip on aluminum surface with small-amplitude roughness

    by Chengpeng Zhang, Zhaoliang Jiang, Jilai Wang, Li Zhao, Ding Wang, Cheng Zhang

    Boundary slip has a significant influence on micro/nano-scale flow and its quantitative description has become a prerequisite for design and fabrication of micro/nano-scale fluid systems. In this research, a physical model for boundary slip on aluminum surface with small-amplitude roughness was proposed, which considered the synergistic effects of solid-liquid interface parameters such as fluid properties, wettability and roughness. Besides, the boundary slip experiments were carried out using atomic force microscope (AFM) method to verify model accuracy. According to experimental results, the roughness ( Ra ) values of different aluminum surfaces were 0.47 nm, 1.16 nm, 1.94 nm, 2.63 nm and 3.18 nm, respectively. Correspondingly, the slip lengths were 23.7 nm, 20.3 nm, 18.5 nm, 15.9 nm and 12.7 nm, respectively. It was found the proposed slip model was in good agreement with experimental results, which could describe boundary slip on rough surface more accurately. This research could provide beneficial guidance for understanding of physical mechanism and quantitative description of boundary slip on solid surface with small-amplitude roughness.

  • Review of Imprinted Polymer Microrings as Ultrasound Detectors: Design, Fabrication, and Characterization

    by Cheng Zhang, Sung-Liang Chen, Tao Ling, L. Jay Guo

    Detectors play a vital role in ultrasound sensing and imaging applications. With the rapid development of photoacoustic imaging technology in recent years, novel ultrasound detectors based on optical methods have gained increased attention, among which the imprinted polymer microring is a representative one. This review covers the device design, fabrication, and characterization, with an emphasis on how the imprinting-based fabrication methodology benefits the device performance, which further facilitates photoacoustic imaging and sensing applications. By carefully designing and fabricating the imprint mold, the imprinted polymer microring has a quality factor on the order of $10^{5}$ at 780 nm. The device has advantages such as wide acoustic bandwidth response from dc to 350 MHz at −3 dB, low noise equivalent detectable pressure, wide acceptance angle, and so on. The polymer microring has been successfully employed in applications such as photoacoustic imaging and real-time terahertz pulse detection.


  • Molecular Dynamics Simulation of Size Effect on the Mechanical Properties of Amorphous Silica

    by Fang Li Duan, Cheng Zhang, Qing Song Liu

    The frustules of diatoms have excellent elasticity and high strength, but their main composition, amorphous silica, is a kind of typical brittle material. Molecular dynamics simulations of the uniaxial tension were carried out to study the size effect on the mechanical properties of amorphous silica. Stress-strain behavior, the radius of biggest void, radial distribution functions and bond angle distribution were analyzed. Our results show the small model exhibits a better ultimate strength, ductility and toughness than the large model, and the generation and expansion of voids plays an important role in the fracture behavior of the model. For the small model, some of Si-O bonds are stretched, and the average of O-Si-O bond angle decreases from 108o to 95o, which makes the model have a capability to perform larger plastic deformation and lead to a better ductility. However, for the large model, except the change of Si-O-Si bond angle, its structure has no other significant changes. Our results demonstrate that changes of size have significant impact on the mechanical properties and deformation mechanism of intrinsically brittle materials at the nanoscale.