Peidong Xu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Peidong Xu has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Mingyong Liu
Hubei Agricultural Machinery Engineering Research and Design Institute Hubei University of Technology Wuhan China
2 shared publications - Chenhui Wu
Hubei Agricultural Machinery Engineering Research and Design Institute, Hubei University of Technology, Wuhan 430068, China
1 shared publication - Chunai Yan
Intelligent Manufacturing Institute, Wuchang Institute of Technology Wuhan China
1 shared publication - Haofeng Ku
Hubei Agricultural Machinery Engineering Research and Design Institute, Hubei University of Technology, Wuhan 430068, China
1 shared publication - Jinxi Zhang
Hubei Agricultural Machinery Engineering Research and Design Institute, Hubei University of Technology, Wuhan 430068, China
1 shared publication
Latest Publications
- Open Access
- 22 January 2020
- Published by Hindawi Limited in Mathematical Problems in Engineering
- Vol. 2020, 1-14
Predicting Fatigue Life for Finite Line Contact under Starved Elastohydrodynamic Lubrication Condition
Surface contact fatigue is the main failure mode in many mechanical components, such as gears, bearings, and cam-followers. A fatigue life prediction model is proposed for finite line contact under starved thermal elastohydrodynamic lubrication (TEHL) condition in this paper. Then, the effects of inlet oil-supply thickness, slide-to-roll ratio (SRR), and operating conditions on the lubrication performance and fatigue life are investigated. The results show that the lubrication characteristics and fatigue life of finite line contact are obviously different from those of fully flooded situation by introducing the starved lubrication condition. For example, the severe starved conditions lead to a significant increase in friction coefficient and decreased fatigue life. The variation of SRR has an important influence on the fatigue life. With the increase of SRR, the fatigue life decreases firstly and then increases. The stress concentration occurs near the surface when speed is low. In addition, under the low-speed situation, rotation speed variation has little effect on the fatigue life.
- 22 January 2020
- Published by Hindawi Limited in Mathematical Problems in Engineering
- Vol. 2020, 1-14
Open AccessPredicting Fatigue Life for Finite Line Contact under Starved Elastohydrodynamic Lubrication Condition
Surface contact fatigue is the main failure mode in many mechanical components, such as gears, bearings, and cam-followers. A fatigue life prediction model is proposed for finite line contact under starved thermal elastohydrodynamic lubrication (TEHL) condition in this paper. Then, the effects of inlet oil-supply thickness, slide-to-roll ratio (SRR), and operating conditions on the lubrication performance and fatigue life are investigated. The results show that the lubrication characteristics and fatigue life of finite line contact are obviously different from those of fully flooded situation by introducing the starved lubrication condition. For example, the severe starved conditions lead to a significant increase in friction coefficient and decreased fatigue life. The variation of SRR has an important influence on the fatigue life. With the increase of SRR, the fatigue life decreases firstly and then increases. The stress concentration occurs near the surface when speed is low. In addition, under the low-speed situation, rotation speed variation has little effect on the fatigue life.
- 20 August 2018
- Published by ASME International in Journal of Tribology
- Vol. 141 (1)
Parametric Studies of Mechanical Power Loss for Helical Gear Pair Using a Thermal Elastohydrodynamic Lubrication Model
In this study, a comprehensive mechanical efficiency model based on the thermal elastohydrodynamic lubrication (TEHL) is developed for a helical gear pair. The tribological performance of the helical gear pair is evaluated in terms of the average film thickness, friction coefficient, mechanical power loss, mechanical efficiency, etc. The influence of basic design parameters, working conditions, thermal effect, and surface roughness are studied under various transmission ratios. Results show that the contribution of thermal effect on the tribological performance is remarkable. Meanwhile, the rolling power loss constitutes an important portion of the total mechanical power loss, especially around the meshing position where the pitch point is located in the middle of contact line and the full elastohydrodynamic lubrication (EHL) state with the friction coefficient less than 0.005. The proper increase of normal pressure angle and number of tooth can improve the tribological performance. The influence of helix angle on the mechanical efficiency is less significant. A positive addendum modification coefficient for pinion and a negative addendum modification coefficient for wheel are good for improving the mechanical efficiency. The results provide the tribological guidance for design of a helical gear pair in engineering.
- 20 August 2018
- Published by ASME International in Journal of Tribology
- Vol. 141 (1)
Parametric Studies of Mechanical Power Loss for Helical Gear Pair Using a Thermal Elastohydrodynamic Lubrication Model
In this study, a comprehensive mechanical efficiency model based on the thermal elastohydrodynamic lubrication (TEHL) is developed for a helical gear pair. The tribological performance of the helical gear pair is evaluated in terms of the average film thickness, friction coefficient, mechanical power loss, mechanical efficiency, etc. The influence of basic design parameters, working conditions, thermal effect, and surface roughness are studied under various transmission ratios. Results show that the contribution of thermal effect on the tribological performance is remarkable. Meanwhile, the rolling power loss constitutes an important portion of the total mechanical power loss, especially around the meshing position where the pitch point is located in the middle of contact line and the full elastohydrodynamic lubrication (EHL) state with the friction coefficient less than 0.005. The proper increase of normal pressure angle and number of tooth can improve the tribological performance. The influence of helix angle on the mechanical efficiency is less significant. A positive addendum modification coefficient for pinion and a negative addendum modification coefficient for wheel are good for improving the mechanical efficiency. The results provide the tribological guidance for design of a helical gear pair in engineering.