Ali Işiktaş
Research Subjects
Ali Işiktaş has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Fatih Balıkoğlu
Mechanical Engineering , Balikesir University , Balikesir , Türkiye
3 shared publications - Tayfur Kerem Demircioğlu
BALIKESİR ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ, MAKİNE MÜHENDİSLİĞİ PR
2 shared publications - Vedat Taskin
Trakya Universitesi
2 shared publications Ahmet Durak
Motor Vehicles and Transportation Department, Hayrabolu Vocational School Tekirdağ Namık Kemal University Tekirdağ Türkiye
1 shared publication- Mehmet Özer
BALIKESIR UNIVERSITY, BİGADİÇ VOCATIONAL SCHOOL, DEPARTMENT OF TRANSPORTATION SERVICES
1 shared publication Tayfur Kerem Demircioğlu
Mechanical Engineering Department, Engineering Faculty Balıkesir University Balıkesir Türkiye
1 shared publication
Latest Publications
- 19 June 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (17) , 16456-16467
Experimental Study and Artificial Intelligence‐Based Modeling of the Indentation Behavior of Adhesive‐Bonded Curved Composites
The aim of this research is to investigate the effect of patch layup stacking, thickness, and radius of curvature on the energy absorption and load‐carrying capacity of adhesive‐bonded curved glass fiber laminated composite specimens under indentation loads. A testing machine with a hemispherical indentation apparatus was used to evaluate the damage resistance of curved composites. The indentation resistance increased with increasing radius of curvature in both monolithic and bonded curved composite specimens. The specimens with [0/90] n orientation exhibited higher absorbed energy values and indentation resistance compared to those with [±45] n orientation. The number or thickness of fibers in the upper and lower layers used in the repair process influenced the energy absorption capacity. Applying thicker layers in the indentation direction of bonded curved composite specimens produced superior indentation resistance. The degree of delamination damage was influenced by the curvature diameter and layer configuration, with delamination dominant in bonded samples. Additionally, an artificial neural network was used to predict the indentation responses of bonded curved composite specimens. The ANN model accurately simulated the force–displacement curves and peak forces of monolithic and bonded curved laminates.
- 19 June 2025
- Published by Wiley in Polymer Composites
- Vol. 46 (17) , 16456-16467
Experimental Study and Artificial Intelligence‐Based Modeling of the Indentation Behavior of Adhesive‐Bonded Curved Composites
The aim of this research is to investigate the effect of patch layup stacking, thickness, and radius of curvature on the energy absorption and load‐carrying capacity of adhesive‐bonded curved glass fiber laminated composite specimens under indentation loads. A testing machine with a hemispherical indentation apparatus was used to evaluate the damage resistance of curved composites. The indentation resistance increased with increasing radius of curvature in both monolithic and bonded curved composite specimens. The specimens with [0/90] n orientation exhibited higher absorbed energy values and indentation resistance compared to those with [±45] n orientation. The number or thickness of fibers in the upper and lower layers used in the repair process influenced the energy absorption capacity. Applying thicker layers in the indentation direction of bonded curved composite specimens produced superior indentation resistance. The degree of delamination damage was influenced by the curvature diameter and layer configuration, with delamination dominant in bonded samples. Additionally, an artificial neural network was used to predict the indentation responses of bonded curved composite specimens. The ANN model accurately simulated the force–displacement curves and peak forces of monolithic and bonded curved laminates.
- 3 April 2024
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Effect of adhesive thickness and loading speed on adhesion strength in single-lap adhesive joints with aluminum 5754
This study provides shear test results of single-lap adhesive joints with aluminum 5754. To investigate the effect of adhesive thickness on joint strength in single-lap adhesive joints, three different thicknesses (0.2, 1, and 2 mm) were applied. Increasing the adhesive thickness from 0.2 mm to 1 mm and from 0.2 mm to 2 mm resulted in a reduction in shear load of roughly 36% and 44%, respectively. It has been observed that the joint strength decreases with increasing adhesive thickness in single-lap adhesive joints with aluminum 5754. In addition, single-lap adhesive joints were tested at various loading rates (1, 10, and 100 mm/min), and the influence of loading speed on adhesive strength was studied. The shear load increased with the loading speed in the test results of single-lap adhesive joints.
- 3 April 2024
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
Effect of adhesive thickness and loading speed on adhesion strength in single-lap adhesive joints with aluminum 5754
This study provides shear test results of single-lap adhesive joints with aluminum 5754. To investigate the effect of adhesive thickness on joint strength in single-lap adhesive joints, three different thicknesses (0.2, 1, and 2 mm) were applied. Increasing the adhesive thickness from 0.2 mm to 1 mm and from 0.2 mm to 2 mm resulted in a reduction in shear load of roughly 36% and 44%, respectively. It has been observed that the joint strength decreases with increasing adhesive thickness in single-lap adhesive joints with aluminum 5754. In addition, single-lap adhesive joints were tested at various loading rates (1, 10, and 100 mm/min), and the influence of loading speed on adhesive strength was studied. The shear load increased with the loading speed in the test results of single-lap adhesive joints.
- 8 March 2024
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Experimental study on resin pin-reinforced marine sandwich composites under quasi-static indentation load
This study aims to experimentally examine the indentation behaviour of marine sandwich composites with pin-reinforced polyvinyl chloride foam core and E-glass face sheets. The effects of indenter diameter, resin pin diameter, and arrangement on force-displacement, maximum contact force, and absorbed energy values of sandwich panels were evaluated by the indentation tests. Throughout the experiments, the contact forces increased as the pin diameter increased. The contact forces reduced as the distance between pin diameters increased. Additionally, the values of absorbed energy increased as the diameters of the resin pin and indenter increased. Placing the pins more closely together additionally allows the material to absorb more energy in the event of indentation. A visual inspection took place on the post-indentation cross-sections of the sandwich specimens to detect any damage modes. Damage modes varied depending on the size of the indenter and the hole pattern in the foam core.
- 8 March 2024
- Published by Omer Halisdemir Universitesi in Ömer Halisdemir Üniversitesi Mühendislik Bilimleri Dergisi
Experimental study on resin pin-reinforced marine sandwich composites under quasi-static indentation load
This study aims to experimentally examine the indentation behaviour of marine sandwich composites with pin-reinforced polyvinyl chloride foam core and E-glass face sheets. The effects of indenter diameter, resin pin diameter, and arrangement on force-displacement, maximum contact force, and absorbed energy values of sandwich panels were evaluated by the indentation tests. Throughout the experiments, the contact forces increased as the pin diameter increased. The contact forces reduced as the distance between pin diameters increased. Additionally, the values of absorbed energy increased as the diameters of the resin pin and indenter increased. Placing the pins more closely together additionally allows the material to absorb more energy in the event of indentation. A visual inspection took place on the post-indentation cross-sections of the sandwich specimens to detect any damage modes. Damage modes varied depending on the size of the indenter and the hole pattern in the foam core.
- Open Access
- 15 January 2024
- Published by Dicle Universitesi Muhendislik Fakultesi Muhendislik Dergisi in Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi
- Vol. 15 (1) , 169-175
Kör delik delmenin alüminyum 5754 ile oluşturulan tek bindirmeli yapıştırma bağlantıların kayma dayanımına etkisi
Bu çalışmada, Alüminyum 5754 ile oluşturulan tek bindirmeli yapıştırma bağlantıların kayma test sonuçlarına yer verilmiştir. Kapalı delik delme işleminin yapıştırıcı ile birleştirilmiş bağlantılar üzerindeki etkisini araştırmak amacıyla alüminyumların yüzeylerine delikler delinerek farklı tipte bağlantı konfigürasyonları oluşturulmuştur. Bağlantıdaki alüminyum parçalardan biri delikli olduğunda, Araldite 2015 kullanılan bağlantıların hasar yükünde, her ikisi de deliksiz alüminyumlara göre %39 artış görülmüştür. Araldite AV138 kullanılan bağlantılardaki hasar yükünde ise artış %54 olmuştur. Bağlantıdaki alüminyumlardan ikisi de delikli olduğunda, Araldite 2015 kullanılan bağlantılardaki hasar yükünde, her ikisi de deliksiz alüminyumlara göre %98 artış görülmüştür. Araldite AV138 kullanılan bağlantılardaki hasar yükünde ise artış %165 olmuştur. Ayrıca, Araldite 2015 kullanılan numunelerin kayma testlerindeki uzama miktarları Araldite AV 138 kullanılan numunelere göre daha yüksek çıkmıştır.
- 15 January 2024
- Published by Dicle Universitesi Muhendislik Fakultesi Muhendislik Dergisi in Dicle Üniversitesi Mühendislik Fakültesi Mühendislik Dergisi
- Vol. 15 (1) , 169-175
Open AccessKör delik delmenin alüminyum 5754 ile oluşturulan tek bindirmeli yapıştırma bağlantıların kayma dayanımına etkisi
Bu çalışmada, Alüminyum 5754 ile oluşturulan tek bindirmeli yapıştırma bağlantıların kayma test sonuçlarına yer verilmiştir. Kapalı delik delme işleminin yapıştırıcı ile birleştirilmiş bağlantılar üzerindeki etkisini araştırmak amacıyla alüminyumların yüzeylerine delikler delinerek farklı tipte bağlantı konfigürasyonları oluşturulmuştur. Bağlantıdaki alüminyum parçalardan biri delikli olduğunda, Araldite 2015 kullanılan bağlantıların hasar yükünde, her ikisi de deliksiz alüminyumlara göre %39 artış görülmüştür. Araldite AV138 kullanılan bağlantılardaki hasar yükünde ise artış %54 olmuştur. Bağlantıdaki alüminyumlardan ikisi de delikli olduğunda, Araldite 2015 kullanılan bağlantılardaki hasar yükünde, her ikisi de deliksiz alüminyumlara göre %98 artış görülmüştür. Araldite AV138 kullanılan bağlantılardaki hasar yükünde ise artış %165 olmuştur. Ayrıca, Araldite 2015 kullanılan numunelerin kayma testlerindeki uzama miktarları Araldite AV 138 kullanılan numunelere göre daha yüksek çıkmıştır.
- 25 December 2020
- Published by SDU Journal of Natural and Applied Sciences in SDÜ Fen Bilimleri Enstitüsü Dergisi
- Vol. 24 (3) , 696-701
Fiber Metal Laminatların Şekillendirilebilme Kabiliyetinin İncelenmesi
Bu çalışmada, havacılık sektöründe kullanılan fiber metal laminatların (FML) şekillendirilebilme kabiliyeti deneysel olarak incelenmiştir. FML numunelerin alt ve üst tabakalarında iki farklı kalınlıkta (0,6 ve 1,2 mm) Al5754-H22 sac levhalar kullanılmıştır. FML numunelerin orta tabakasında prepreg karbon elyaf kumaştan üretilen karbon elyaf plaka bulunmaktadır. FML malzemelerin şekillendirilme kabiliyetini incelemek amacıyla numuneler farklı bükme açılarında şekillendirilmiştir. Deneyler sırasında 0,6 mm Al 5754 kullanılan FML numuneler tüm bükme açılarında şekillendirilirken, 1,2 mm Al 5754 kullanılan FML numunelerin 75° ve 90° bükme testlerinde ise numunelerin dış tarafındaki alüminyum tabakasında yırtılma hasarı görülmüştür. Ayrıca FML numunelerin şekillendirilmesinde, bükme açısı ve alüminyum tabaka kalınlığının artmasıyla bükme kuvveti değerinin arttığı tespit edilmiştir.
- 25 December 2020
- Published by SDU Journal of Natural and Applied Sciences in SDÜ Fen Bilimleri Enstitüsü Dergisi
- Vol. 24 (3) , 696-701
Fiber Metal Laminatların Şekillendirilebilme Kabiliyetinin İncelenmesi
Bu çalışmada, havacılık sektöründe kullanılan fiber metal laminatların (FML) şekillendirilebilme kabiliyeti deneysel olarak incelenmiştir. FML numunelerin alt ve üst tabakalarında iki farklı kalınlıkta (0,6 ve 1,2 mm) Al5754-H22 sac levhalar kullanılmıştır. FML numunelerin orta tabakasında prepreg karbon elyaf kumaştan üretilen karbon elyaf plaka bulunmaktadır. FML malzemelerin şekillendirilme kabiliyetini incelemek amacıyla numuneler farklı bükme açılarında şekillendirilmiştir. Deneyler sırasında 0,6 mm Al 5754 kullanılan FML numuneler tüm bükme açılarında şekillendirilirken, 1,2 mm Al 5754 kullanılan FML numunelerin 75° ve 90° bükme testlerinde ise numunelerin dış tarafındaki alüminyum tabakasında yırtılma hasarı görülmüştür. Ayrıca FML numunelerin şekillendirilmesinde, bükme açısı ve alüminyum tabaka kalınlığının artmasıyla bükme kuvveti değerinin arttığı tespit edilmiştir.
- Open Access
- 10 January 2020
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 22 (1) , 281-290
Effect of bending angles and bending directions on springback in V-bending of aluminum-carbon fiber sandwich composite plates
Bu çalışmada, alüminyum-karbon elyaf sandviç levhaların V bükme operasyonu neticesinde oluşan geri esneme davranışı deneysel olarak incelenmiştir. Bükme yönünün geri esneme davranışı üzerine olan etkisini incelemek amacıyla farklı bükme yönlerindeki sandviç kompozit levhalar 15°, 30°, 45°, 60°, 75° ve 90° bükme açılarında şekillendirilmiştir. Farklı bükme yönlerinde şekillendirilen sandviç kompozit levhalarda meydana gelen geri esneme değerlerinin birbirine çok yakın olduğu tespit edilmiştir. Ayrıca, T1 (saat yönünün tersinde) bükme yönündeki sandviç kompozit levhaların 75° ve 90° bükme açılarındaki testlerinde alüminyum ve karbon elyaf plakalar arasında açılmalar görülürken, T2 (saat yönünde) bükme yönündeki sandviç kompozit levhaların 75° ve 90° bükme açılarında ise dış taraftaki alüminyum sac levhalarda yırtılmalar oluşmuştur.
- 10 January 2020
- Published by Balikesir Universitesi Fen Bilimleri Enstitusu Dergisi in Balıkesir Üniversitesi Fen Bilimleri Enstitüsü Dergisi
- Vol. 22 (1) , 281-290
Open AccessEffect of bending angles and bending directions on springback in V-bending of aluminum-carbon fiber sandwich composite plates
Bu çalışmada, alüminyum-karbon elyaf sandviç levhaların V bükme operasyonu neticesinde oluşan geri esneme davranışı deneysel olarak incelenmiştir. Bükme yönünün geri esneme davranışı üzerine olan etkisini incelemek amacıyla farklı bükme yönlerindeki sandviç kompozit levhalar 15°, 30°, 45°, 60°, 75° ve 90° bükme açılarında şekillendirilmiştir. Farklı bükme yönlerinde şekillendirilen sandviç kompozit levhalarda meydana gelen geri esneme değerlerinin birbirine çok yakın olduğu tespit edilmiştir. Ayrıca, T1 (saat yönünün tersinde) bükme yönündeki sandviç kompozit levhaların 75° ve 90° bükme açılarındaki testlerinde alüminyum ve karbon elyaf plakalar arasında açılmalar görülürken, T2 (saat yönünde) bükme yönündeki sandviç kompozit levhaların 75° ve 90° bükme açılarında ise dış taraftaki alüminyum sac levhalarda yırtılmalar oluşmuştur.