Liyuan Dong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Liyuan Dong has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Xiao Zhao
School of Geophysics and Information Technology, China University of Geosciences (Beijing), Beijing 100083, China
4 shared publications - Lanya Yu
School of Geophysics and Information Technology, China University of Geosciences, Beijing, China
2 shared publications - Shuoyang Li
School of Geophysics and Information Technology, China University of Geosciences, Beijing, China
2 shared publications - Boran Wen
School of Geophysics and Information Technology, China University of Geosciences (Beijing), Beijing 100083, China
1 shared publication - Qisheng Zhang
School of Geophysics and Information Technology, China University of Geosciences (Beijing), Beijing, China
1 shared publication - Xiaolong Lv
School of Geophysics and Information Technology, China University of Geosciences (Beijing), Beijing 100083, China
1 shared publication
Latest Publications
- 4 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (4) , 4039-4049
Multiple Adaptive Current Feedback Technique for Small-Gain Stages in Adaptively Biased Low-Dropout Regulator
Adaptive bias scheme, which can be used to provide a current proportional to the current flowing through the power transistor under high current load, avoiding the need for providing additional large fixed bias current to the circuit, has been adopted in many low-dropout regulators (LDO). When an adaptive bias scheme is applied to an LDO with a current mirror buffer, although a low chip area consumption and a better transient response can be achieved, the loop gain of LDO at high-load current and loop bandwidth at low load are still low. In previous works, multiple small-gain stages can effectively improve the gain and bandwidth but may lead to stability problems or even need to consume large currents to ensure stability, thus affecting current efficiency. This article proposes the multiple adaptive current feedbacks technique for small-gain stages in adaptively biased low dropout regulator (AB-LDO) with a current mirror buffer, improving the loop gain and bandwidth and eliminating the need for frequency compensation to meet stability requirements. Moreover, in the case that multiple adaptive bias loops can be introduced after the proposed technique is applied to this design, an intuitive and simple method is adopted to analyze the whole circuit. The designed AB-LDO was fabricated in Semiconductor Manufacturing International Corp (SMIC) 0.18- $\mu$ m process. The measured results show that the designed LDO realizes 30.75-mV transient performances with a step of 10 ns.
- 4 November 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 37 (4) , 4039-4049
Multiple Adaptive Current Feedback Technique for Small-Gain Stages in Adaptively Biased Low-Dropout Regulator
Adaptive bias scheme, which can be used to provide a current proportional to the current flowing through the power transistor under high current load, avoiding the need for providing additional large fixed bias current to the circuit, has been adopted in many low-dropout regulators (LDO). When an adaptive bias scheme is applied to an LDO with a current mirror buffer, although a low chip area consumption and a better transient response can be achieved, the loop gain of LDO at high-load current and loop bandwidth at low load are still low. In previous works, multiple small-gain stages can effectively improve the gain and bandwidth but may lead to stability problems or even need to consume large currents to ensure stability, thus affecting current efficiency. This article proposes the multiple adaptive current feedbacks technique for small-gain stages in adaptively biased low dropout regulator (AB-LDO) with a current mirror buffer, improving the loop gain and bandwidth and eliminating the need for frequency compensation to meet stability requirements. Moreover, in the case that multiple adaptive bias loops can be introduced after the proposed technique is applied to this design, an intuitive and simple method is adopted to analyze the whole circuit. The designed AB-LDO was fabricated in Semiconductor Manufacturing International Corp (SMIC) 0.18- $\mu$ m process. The measured results show that the designed LDO realizes 30.75-mV transient performances with a step of 10 ns.
- 1 May 2021
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 134, 153643
A 101 dB SNR fourth-order ΣΔ modulator for MEMS digital geophones
- 1 May 2021
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 134, 153643
A 101 dB SNR fourth-order ΣΔ modulator for MEMS digital geophones
- 24 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (10) , 10477-10488
Design of an Adaptively Biased Low-Dropout Regulator With a Current Reusing Current-Mode OTA Using an Intuitive Analysis Method
An adaptively biased low dropout regulator (ABLDO) with current mirror buffer has been proposed in previous literatures, which only solves a few of specific problems of AB-LDO without additional synthetical analysis of the various performances. Based on the analysis, it is found that enhancing the current efficiency of operational transconductance amplifier (OTA) is a key factor to improve the performances of ABLDO. And a current reusing current-mode OTA (CRCM-OTA) with high current efficiency is proposed to apply to AB-LDO. Compared with the traditional AB-LDO, it can achieve an obvious improvement of AB-LDO performances including the current efficiency of AB-LDO, loop gain and loop bandwidth without increasing the area and power consumption. This paper also adopts an intuitive method different from the previous works to analyze the whole loop. The AB-LDO using an advanced CRCM-OTA was fabricated in SMIC 0.18μm CMOS process, which has a transient undershoot of 26.25mV with an output capacitor of 1μF for a load step of 0-50mA with edge time of 10ns and realizes a performance figure of merit (F oM) value of 13.65ps.
- 24 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 35 (10) , 10477-10488
Design of an Adaptively Biased Low-Dropout Regulator With a Current Reusing Current-Mode OTA Using an Intuitive Analysis Method
An adaptively biased low dropout regulator (ABLDO) with current mirror buffer has been proposed in previous literatures, which only solves a few of specific problems of AB-LDO without additional synthetical analysis of the various performances. Based on the analysis, it is found that enhancing the current efficiency of operational transconductance amplifier (OTA) is a key factor to improve the performances of ABLDO. And a current reusing current-mode OTA (CRCM-OTA) with high current efficiency is proposed to apply to AB-LDO. Compared with the traditional AB-LDO, it can achieve an obvious improvement of AB-LDO performances including the current efficiency of AB-LDO, loop gain and loop bandwidth without increasing the area and power consumption. This paper also adopts an intuitive method different from the previous works to analyze the whole loop. The AB-LDO using an advanced CRCM-OTA was fabricated in SMIC 0.18μm CMOS process, which has a transient undershoot of 26.25mV with an output capacitor of 1μF for a load step of 0-50mA with edge time of 10ns and realizes a performance figure of merit (F oM) value of 13.65ps.
- Open Access
- 20 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 22664-22671
A High Current Efficiency Two-Stage Amplifier With Inner Feedforward Path Compensation Technique
A high current efficiency two-stage amplifier with inner feedforward path compensation (IFPC) technique is proposed in this paper. To improve the current utilization of the whole structure, the recycling folded cascode amplifier (RFC) is adopted as the first stage, and the inner feedforward path which is used to eliminate the non-dominant pole is composed of the input stage of RFC and the tail current transistor of the second stage amplifier. By using the IFPC technique, the proposed amplifier achieves an extended gain-bandwidth (GBW) and sufficient phase margin (PM) compared to that of the two-stage amplifier using single Miller compensation (SMC). Moreover, this compensation technique avoids extra power consumption since it does not require additional circuits. The proposed two-stage IFPC amplifier was fabricated in a 0.18 μm CMOS technology and the chip area of it is about 0.076mm2. The simulated open loop AC response shows the DC gain, GBW, and PM are 130dB, 2.01MHz, and 58.3∘, respectively. Measured results of transient response show when driving a 120pF load capacitance, the proposed amplifier achieves 368ns average 1% settling time, and about 1.56V/μs average slew rate (SR). Note that under the condition of 1.8V power supply, the power consumption is only 108μW, proving the proposed two-stage IFPC amplifier can achieve high current efficiency while maintaining stability.
- 20 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 22664-22671
Open AccessA High Current Efficiency Two-Stage Amplifier With Inner Feedforward Path Compensation Technique
A high current efficiency two-stage amplifier with inner feedforward path compensation (IFPC) technique is proposed in this paper. To improve the current utilization of the whole structure, the recycling folded cascode amplifier (RFC) is adopted as the first stage, and the inner feedforward path which is used to eliminate the non-dominant pole is composed of the input stage of RFC and the tail current transistor of the second stage amplifier. By using the IFPC technique, the proposed amplifier achieves an extended gain-bandwidth (GBW) and sufficient phase margin (PM) compared to that of the two-stage amplifier using single Miller compensation (SMC). Moreover, this compensation technique avoids extra power consumption since it does not require additional circuits. The proposed two-stage IFPC amplifier was fabricated in a 0.18 μm CMOS technology and the chip area of it is about 0.076mm2. The simulated open loop AC response shows the DC gain, GBW, and PM are 130dB, 2.01MHz, and 58.3∘, respectively. Measured results of transient response show when driving a 120pF load capacitance, the proposed amplifier achieves 368ns average 1% settling time, and about 1.56V/μs average slew rate (SR). Note that under the condition of 1.8V power supply, the power consumption is only 108μW, proving the proposed two-stage IFPC amplifier can achieve high current efficiency while maintaining stability.