Wonjin Choi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wonjin Choi has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- EunMi Choi
Ulsan National Institute of Science and Technology
5 shared publications Hong Eun Choi
Department of Electrical Engineering, Ulsan National Institute of Science and Technology, Ulsan, South Korea
2 shared publications- Ingeun Lee
Department of Electrical Engineering, Ulsan National Institute of Science and Technology, Ulsan, South Korea
2 shared publications - Jinwoo Shin
Quantum Physics Technology Directorate, Agency for Defense Development, Daejeon 34186, Korea
2 shared publications Anna Alexnader
Los Alamos National Laboratory
1 shared publicationApril Smith
Los Alamos National Laboratory
1 shared publication
Latest Publications
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Space Charge Neutralization Studies for H+ Beamline
- 1 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1
Space Charge Neutralization Studies for H+ Beamline
- 18 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 459-466
Advanced Bragg Resonator Integration for Enhanced Bandwidth and Stability in G-Band TWT With Staggered Double Vane Structure
This article presents the design and analysis of a wideband staggered double vane (SDV) sheet-beam-based traveling-wave tube (TWT) for stable amplification in the G-band. Unlike conventional SDV structures, which often suffer from oscillations within the interaction region due to upper and lower cutoff regions, our design employs several key innovations to overcome these limitations. First, the newly designed filter configuration effectively eliminates oscillations within the interaction region. Second, the shape of the Bragg resonator is modified to a diamond configuration, which significantly enhanced impedance matching around 200 GHz, ensuring broader bandwidth and improved transmission characteristics. Finally, we discuss the advantages of E -plane fabrication compared to H -plane fabrication and presents a study on the design of an E -plane filter structure that is feasible for manufacturing. Particle-in-cell (PIC) simulations and experimental validations confirm that our proposed design achieves a 40 GHz 3 dB bandwidth and stable operation without oscillations, demonstrating its potential for high-performance millimeter-wave (mmWave) applications.
- 18 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 459-466
Advanced Bragg Resonator Integration for Enhanced Bandwidth and Stability in G-Band TWT With Staggered Double Vane Structure
This article presents the design and analysis of a wideband staggered double vane (SDV) sheet-beam-based traveling-wave tube (TWT) for stable amplification in the G-band. Unlike conventional SDV structures, which often suffer from oscillations within the interaction region due to upper and lower cutoff regions, our design employs several key innovations to overcome these limitations. First, the newly designed filter configuration effectively eliminates oscillations within the interaction region. Second, the shape of the Bragg resonator is modified to a diamond configuration, which significantly enhanced impedance matching around 200 GHz, ensuring broader bandwidth and improved transmission characteristics. Finally, we discuss the advantages of E -plane fabrication compared to H -plane fabrication and presents a study on the design of an E -plane filter structure that is feasible for manufacturing. Particle-in-cell (PIC) simulations and experimental validations confirm that our proposed design achieves a 40 GHz 3 dB bandwidth and stable operation without oscillations, demonstrating its potential for high-performance millimeter-wave (mmWave) applications.
- 23 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (3) , 1121-1127
Stability Analysis of 300-GHz Sheet Electron Beam Transport in a Periodic Rectangular Quadrupole
A novel periodic magnetic focusing system is proposed. The stability of elliptical sheet beam transport in the magnetic field of a periodic rectangular quadrupole (PRQ) is studied and compared with that in the magnetic field of periodically cusped magnets (PCMs). Theoretically predicted matching conditions are verified by numerical simulations. An 11.7- kV, 35-mA, 0.32 mm x 0.06 mm elliptical sheet beam is confined in a 0.53 mm x 0.08 mm beam tunnel and transported over a distance of 30 mm. Both the PCM and PRQ have similar characteristics of electron beam distribution change, beam emittance, and beam transmission. The results of the initial stability analysis indicate that PCMs are preferable to PRQs because of their ability to confine the beam with a long magnet period.
- 23 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 49 (3) , 1121-1127
Stability Analysis of 300-GHz Sheet Electron Beam Transport in a Periodic Rectangular Quadrupole
A novel periodic magnetic focusing system is proposed. The stability of elliptical sheet beam transport in the magnetic field of a periodic rectangular quadrupole (PRQ) is studied and compared with that in the magnetic field of periodically cusped magnets (PCMs). Theoretically predicted matching conditions are verified by numerical simulations. An 11.7- kV, 35-mA, 0.32 mm x 0.06 mm elliptical sheet beam is confined in a 0.53 mm x 0.08 mm beam tunnel and transported over a distance of 30 mm. Both the PCM and PRQ have similar characteristics of electron beam distribution change, beam emittance, and beam transmission. The results of the initial stability analysis indicate that PCMs are preferable to PRQs because of their ability to confine the beam with a long magnet period.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 8 (6) , 710-718
Microscopic Analyses of Electrical Conductivity of Micromachined-Folded Waveguides Based on Surface Roughness Measurement for Terahertz Vacuum Electron Devices
Manufacturing slow wave vacuum electron device (VED) components operating in a terahertz (THz) region required the use of proper techniques and detailed plans. Moreover, how to fabricate components and evaluate manufactured ones are essential in identifying defects, checking their performance, and finding what needs to be improved. This study introduces estimated conductivity based on the surface roughness and evaluations of fabricated folded waveguides (FWGs), which is one of the THz slow wave VED components, using nanoscale precision computer numerical control (nano-CNC) machining. Produced circuits operating in the G- (0.11-0.3 THz) and Y-bands (0.325-0.5 THz) were diagnosed in terms of the RF transmission loss, achievable surface roughness, tolerance, and flatness. During testing, our devices exhibited the highest reported Ra (arithmetic mean surface roughness) at less than 11.17 nm in the Y-band. The conductivities based on the measured surface roughness were estimated in the G-band and the Y-band. Through a simulation and an experiment, we analyzed the reasons for the losses caused by the reduced electrical conductivity. The main contribution of this work is the demonstration of an achievable conductivity of the THz FWGs fabricated with nano-CNC machining and an improved surface finishing capability of the fabrication technique using lubricants.
- 1 October 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 8 (6) , 710-718
Microscopic Analyses of Electrical Conductivity of Micromachined-Folded Waveguides Based on Surface Roughness Measurement for Terahertz Vacuum Electron Devices
Manufacturing slow wave vacuum electron device (VED) components operating in a terahertz (THz) region required the use of proper techniques and detailed plans. Moreover, how to fabricate components and evaluate manufactured ones are essential in identifying defects, checking their performance, and finding what needs to be improved. This study introduces estimated conductivity based on the surface roughness and evaluations of fabricated folded waveguides (FWGs), which is one of the THz slow wave VED components, using nanoscale precision computer numerical control (nano-CNC) machining. Produced circuits operating in the G- (0.11-0.3 THz) and Y-bands (0.325-0.5 THz) were diagnosed in terms of the RF transmission loss, achievable surface roughness, tolerance, and flatness. During testing, our devices exhibited the highest reported Ra (arithmetic mean surface roughness) at less than 11.17 nm in the Y-band. The conductivities based on the measured surface roughness were estimated in the G-band and the Y-band. Through a simulation and an experiment, we analyzed the reasons for the losses caused by the reduced electrical conductivity. The main contribution of this work is the demonstration of an achievable conductivity of the THz FWGs fabricated with nano-CNC machining and an improved surface finishing capability of the fabrication technique using lubricants.
- 29 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 64 (7) , 2955-2962
Design and Fabrication of a 300 GHz Modified Sine Waveguide Traveling-Wave Tube Using a Nanocomputer Numerical Control Machine
The sine waveguide slow-wave structure is a promising interaction circuit for traveling-wave tubes in the terahertz region because it possesses advantageous properties such as high transmission, easy fabrication, and elimination of the electron beam tunnel. These waveguides could be fabricated by nanocomputer numerical control (CNC) machining, a fabrication method capable of fabricating microscale components. In our study, we evaluate the practical feasibility of manufacturing 300-GHz sine waveguides with the ideal design, using nano-CNC machining. It is found that the ideal sine waveguide circuit must be modified, because of the limitations imposed by the actual tool size of the nano-CNC machine. Simulations of cold- and hot-tests of the circuit-including the electron beam effect-were conducted for both the ideal and the modified sine waveguide circuits. A modified sine waveguide was successfully machined using a nano-CNC machine with a 0.12-mm diameter tool tip. The S-parameters of the fabricated circuit were measured and compared to simulation data. A detailed analysis of the measured transmission loss was performed, and this loss was found to be attributable to a gap left by the assembly process between the two copper plates.
- 29 May 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 64 (7) , 2955-2962
Design and Fabrication of a 300 GHz Modified Sine Waveguide Traveling-Wave Tube Using a Nanocomputer Numerical Control Machine
The sine waveguide slow-wave structure is a promising interaction circuit for traveling-wave tubes in the terahertz region because it possesses advantageous properties such as high transmission, easy fabrication, and elimination of the electron beam tunnel. These waveguides could be fabricated by nanocomputer numerical control (CNC) machining, a fabrication method capable of fabricating microscale components. In our study, we evaluate the practical feasibility of manufacturing 300-GHz sine waveguides with the ideal design, using nano-CNC machining. It is found that the ideal sine waveguide circuit must be modified, because of the limitations imposed by the actual tool size of the nano-CNC machine. Simulations of cold- and hot-tests of the circuit-including the electron beam effect-were conducted for both the ideal and the modified sine waveguide circuits. A modified sine waveguide was successfully machined using a nano-CNC machine with a 0.12-mm diameter tool tip. The S-parameters of the fabricated circuit were measured and compared to simulation data. A detailed analysis of the measured transmission loss was performed, and this loss was found to be attributable to a gap left by the assembly process between the two copper plates.