Fritz Trimpe
Research Subjects
Fritz Trimpe has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Sönke Lück
Institute of System Dynamics and Mechatronics, University of Applied Sciences Bielefeld, 33619 Bielefeld, Germany
2 shared publications - Ahmed Fathy Abouzeid
Department of Electrical Engineering, Port Said University, Port Said, Egypt
1 shared publication Corinna Salander
Chair for Railway Vehicle Technology, University of Stuttgart, Stuttgart, Germany
1 shared publication- Corinna Salander
German Centre for Rail Traffic Research, 01219 Dresden, Germany
1 shared publication - Fernando Briz
University of Oviedo
1 shared publication - Juan Manuel Guerrero
University of Oviedo
1 shared publication
Latest Publications
- Open Access
Co-Simulation-Based Verification of Torsional Vibration Protection of Electric-Driven Railway Vehicle Wheelsets
Torsional vibration is an oscillation phenomenon occurring at driven railway vehicle wheelsets. As the resulting dynamic stresses can be significantly larger than the maximum static motor torque, axle and press fit are at risk of failure. To prevent dangerous vibration events and with these, press fit and axle from failure, traction drive manufactures nowadays used to implement vibration suppression algorithms in drive controls. In this paper, the effectiveness of such suppression algorithms is analyzed. Furthermore, as a pilot survey, we analyze to what extend traction controls influence the excitation of torsional vibration.
Open AccessCo-Simulation-Based Verification of Torsional Vibration Protection of Electric-Driven Railway Vehicle Wheelsets
Torsional vibration is an oscillation phenomenon occurring at driven railway vehicle wheelsets. As the resulting dynamic stresses can be significantly larger than the maximum static motor torque, axle and press fit are at risk of failure. To prevent dangerous vibration events and with these, press fit and axle from failure, traction drive manufactures nowadays used to implement vibration suppression algorithms in drive controls. In this paper, the effectiveness of such suppression algorithms is analyzed. Furthermore, as a pilot survey, we analyze to what extend traction controls influence the excitation of torsional vibration.
- Open Access
Simulation of Torsional Vibration of Driven Railway Wheelsets Respecting the Drive Control Response on the Vibration Excitation in the Wheel-Rail Contact Point
For the stability verification of railway wheelsets in Germany, dynamic torsional stresses must be respected as they affect the axle and press fit stability of a wheelset. These dynamic stresses are applied to a wheelset by torsional vibration. However, dynamic stresses cannot be predicted by calculation, and so time-consuming and cost-intensive test runs are performed to measure the maximum dynamic stresses. Therefore, this article deals with the setup of a simulation model that shall enable the simulative prediction of maximum dynamic torsional stresses. This model respects that vibration excitation originates from the wheel-rail contact point and that the vibration energy input comes from a high-frequency drive train control. The first results show successful simulation of vibration excitation and correlations between adhesion change and maximum dynamic stresses.
Open AccessSimulation of Torsional Vibration of Driven Railway Wheelsets Respecting the Drive Control Response on the Vibration Excitation in the Wheel-Rail Contact Point
For the stability verification of railway wheelsets in Germany, dynamic torsional stresses must be respected as they affect the axle and press fit stability of a wheelset. These dynamic stresses are applied to a wheelset by torsional vibration. However, dynamic stresses cannot be predicted by calculation, and so time-consuming and cost-intensive test runs are performed to measure the maximum dynamic stresses. Therefore, this article deals with the setup of a simulation model that shall enable the simulative prediction of maximum dynamic torsional stresses. This model respects that vibration excitation originates from the wheel-rail contact point and that the vibration energy input comes from a high-frequency drive train control. The first results show successful simulation of vibration excitation and correlations between adhesion change and maximum dynamic stresses.
- 9 February 2020
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 59 (5) , 785-799
Wheel–rail adhesion during torsional vibration of driven railway wheelsets
Stability verification of railway wheelsets in Germany can currently become a process difficult to plan. Besides standardised calculations, expensive and often time-consuming test ride measurements have to be conducted. In particular, determining the maximum dynamic torsional stresses resulting from torsional vibration of wheelsets is a frequently discussed topic. Neither an analytical nor an empirical model has been found yet to predict the named stresses. Actually, they are determined experimentally and the representativeness of the recorded maximum dynamic torque is assured statistically. However, statistical evaluation only deals with axle stresses (torque and bending) itself. The origin of torsional vibration, which is the wheel–rail contact point, is not considered for evaluation. Its conditions are typically described by wheel–rail adhesion characteristics, but normally the necessary quantities describing these characteristics are not measured or not measured in sufficient precision. Therefore, this article analyses high-resolution wheel–rail adhesion data that have been recorded additionally on regular test ride measurements. The analysis of these measurement data leads to the following two correlations: (1) Torsional vibration events occur at a certain ratio of adhesion change and slippage change. (2) Dynamic torque swings up within a characteristic time span.
- 9 February 2020
- Published by Taylor & Francis in Vehicle System Dynamics
- Vol. 59 (5) , 785-799
Wheel–rail adhesion during torsional vibration of driven railway wheelsets
Stability verification of railway wheelsets in Germany can currently become a process difficult to plan. Besides standardised calculations, expensive and often time-consuming test ride measurements have to be conducted. In particular, determining the maximum dynamic torsional stresses resulting from torsional vibration of wheelsets is a frequently discussed topic. Neither an analytical nor an empirical model has been found yet to predict the named stresses. Actually, they are determined experimentally and the representativeness of the recorded maximum dynamic torque is assured statistically. However, statistical evaluation only deals with axle stresses (torque and bending) itself. The origin of torsional vibration, which is the wheel–rail contact point, is not considered for evaluation. Its conditions are typically described by wheel–rail adhesion characteristics, but normally the necessary quantities describing these characteristics are not measured or not measured in sufficient precision. Therefore, this article analyses high-resolution wheel–rail adhesion data that have been recorded additionally on regular test ride measurements. The analysis of these measurement data leads to the following two correlations: (1) Torsional vibration events occur at a certain ratio of adhesion change and slippage change. (2) Dynamic torque swings up within a characteristic time span.